Related Manuals for enz Cutting Ball CB
Summary of Contents for enz Cutting Ball CB
- Page 1 Cutting Ball CB Operating Manual English June 20 fkr June 4, 2020 ©2020 enz® technik ag...
- Page 2 Schwerzbachstrasse 10 CH-6074 Giswil / Switzerland Tel. +41 41 676 77 66 Version Revision: Date Initials Created Oct 16 Tel. +41 41 676 77 67 Conformed Jun 18 info@enz.com Conformed Jun 20 www.enz.com ©2020 enz® technik ag June 4, 2020...
-
Page 3: Table Of Contents
Accessories ............16 Important warning information in this operating manual ..............6 Warning signs according to DIN EN ISO 7010 ..7 Cutting Ball CB .............. 9 (420.0X0A / 420.0X0AS) .......... 9 Area of application ..........9 Part Names ..............9 Technical Data ............ -
Page 4: Introduction
Only qualified technicians are permitted to perform Copyright maintenance and repair work. Without the prior written permission of enz® technik ag, this manual shall not be duplicated partially or in its entirety. It shall not be photocopied, reproduced, translated, or Please refer to the "MAINTENANCE"... -
Page 5: Address
• The cutting ball may be used on the following types of pipes: Plastic, steel and concrete piping • The cutting ball may only be used in enclosed pipes. June 4, 2020 ©2020 enz® technik ag... -
Page 6: Explanation Of General Safety Instructions
The manufacturer cannot be held responsible for any damages resulting from noncompliance with these Proper use and efficient application of the instructions. product ©2020 enz® technik ag June 4, 2020... -
Page 7: Warning Signs According To Din En Iso 7010
Noncompliance can lead to severe injury if present a trip hazard for personnel and skin comes in contact with hot surface(s). pedestrians. Use warning triangles or ropes to block off the working area. June 4, 2020 ©2020 enz® technik ag... - Page 8 Personal protective equipment includes safety goggles, hard hats, safety gloves, hard-toed boots, safety vests as well as tight-fitting overalls. Compliance with in-house regulations is mandatory to prevent accidents in the workplace. ©2020 enz® technik ag June 4, 2020...
-
Page 9: Cutting Ball Cb
Area of application Cutting Ball CB Removal of: • Limescale (42X.0X0A / 42X.0X0AS) • Roots For use in: • Plastic, steel and concrete pipes and drainage lines WARNING Working pressure max. 100 bar at the nozzle (1450 psi) Higher wear of the cutting ball in concrete pipes 425.090A Crushed Carbide... -
Page 10: Technical Data
89 x 96 425.090A 2.26 ½” 100 – 200 2900 89 x 96 425.090AS 89 x 96 2.26 ½” 100 - 200 2900 Installation Safety instructions WARNING DANGER High-pressure water jets! Risk of cutting injury! ©2020 enz® technik ag June 4, 2020... -
Page 11: Assembling The Cutting Ball
• The necessary information on the wastewater flowing through the shaft must be obtained (chemicals, gas, vapors, etc.) • Measuring instruments such as explosive gas meters, oxygen meters, gas warning devices, etc. must be readily available. June 4, 2020 ©2020 enz® technik ag... -
Page 12: Operation
This may damage the ball and the pipe. WARNING Pay attention to the warning signs that inform you of the necessary personal protective Trip hazard! equipment to be worn! ©2020 enz® technik ag June 4, 2020... -
Page 13: Operating The Cutting Ball
Pay special attention to ensure that exiting fluids do not drain into environmentally-sensitive • Pull the tool back at regular intervals to avoid areas. blockages After completing the pipe cleaning process, reseal all shafts. June 4, 2020 ©2020 enz® technik ag... -
Page 14: Adding Vibration
Eccentric weight After use, put the eccentric weight and the lock screw back in place. This will prevent parts from getting lost. Locking screw ©2020 enz® technik ag June 4, 2020... -
Page 15: Maintenance
Loctite No. 243 adhesive. Both threads must be cleaned before applying the adhesive! • Immediately screw the nozzle inserts into the tool body up to the mechanical stop, then use a socket wrench to slightly tighten each insert. June 4, 2020 ©2020 enz® technik ag... -
Page 16: Appendix
Appendix Accessories Item no. Open-end wrench 420.0906 Cleaning set Item no. C202 Socket wrench 5mm Item no. C101 Storage case Item no. 09.006 Bio oil spray Item no. C191 ©2020 enz® technik ag June 4, 2020... - Page 17 June 4, 2020 ©2020 enz® technik ag...
- Page 18 ©2020 enz® technik ag June 4, 2020...
- Page 19 June 4, 2020 ©2020 enz® technik ag...
- Page 20 ©2020 enz® technik ag June 4, 2020...
Need help?
Do you have a question about the Cutting Ball CB and is the answer not in the manual?
Questions and answers