Motorline MLB2 User Manual
  1. Manuals
  2. Brands
  3. Motorline Manuals
  4. Controller
  5. MLB2
  6. User manual

Motorline MLB2 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EN
MLB2
MLB2
INSTALLER AND USER'S MANUAL
v2.0
REV. 07/2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MLB2 and is the answer not in the manual?

Questions and answers

Related Manuals for Motorline MLB2

Summary of Contents for Motorline MLB2

  • Page 1 MLB2 MLB2 INSTALLER AND USER’S MANUAL v2.0 REV. 07/2019...

  • Page 2: Table Of Contents

    CONNECTION SCHEME - POWER SUPPLY indirect contact with electricity. Be cautious when handling CONNECTION SCHEME - CONTROLLER the product and observe all safety procedures in this manual. CONNECTION SCHEME - MLB2 FOR ANOTHER MLB2 07. TROUBLESHOOTING...

  • Page 3: Safety Instructions

    01. SAFETY INSTRUCTIONS GENERAL WARNINGS the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. WARNINGS FOR TECHNICIANS very important. Read all instructions carefully before beginning the installation/usage procedures and keep this manual in a safe place •...
  • Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY • Attach the permanent label for the manual release as close as possible to the release mechanism. • Supplier disclaims any liability if: • Disconnect means, such as a switch or circuit breaker on the electrical •...

  • Page 5: Mlb2

    02. MLB2 PRODUCT DESCRIPTION PACKAGE The MLB2 is suitable for access control of commercial and industrial surfaces, as it can 01• 01 MLB2 02• 01 Remote Control function as a stand-alone access controller, wiegand output keyboard or card reader. It is 03•...

  • Page 6: Installation

    FIX THE REAR COVER Insert the bushings, position the cover in the holes and secure it with the screws. Insert the cable into the hole. ENCLOSURE THE MLB2 Attach the MLB2 to the rear cover, and tighten the set screws.

  • Page 7: Acoustic-Optical Instructions

    04. ACOUSTIC-OPTICAL INSTRUCTIONS 05. PROGRAMMING SOUNDS AND LIGHTS INITIAL SETTING Read card OPERATION STATUS BELL 04• Add card Standby 05• Exit Programming Mode Enter Programming Mode Red flashing light Success Green light on Master Code Fail Di Di Di This code gives you access to the Programming Mode. To be programmed Orange light on Without it, you will not be able to do any user programming or device changes.

  • Page 8: Door Opening 7A

    05. PROGRAMMING 05. PROGRAMMING DOOR OPENING OPERATIONS To unlock the door you can use the Fingerprint or Card or both (depends on the Operating Mode). These operations can only be done in Programming Mode. OPERATIONS INSTRUCTIONS OPERATIONS INSTRUCTIONS Fingerprint Repeat Fingerprint With Auto ID •...

  • Page 9: Delete All Users 8A

    05. PROGRAMMING 05. PROGRAMMING DELETE ALL USERS DOOR WARNING OPEN TOO LONG TIME (DOTL) These operations can only be done in Programming Mode. These operations can only be done in Programming Mode. OPERATIONS INSTRUCTIONS OPERATIONS INSTRUCTIONS • Disable open door detection Master Code (default).

  • Page 10: Alarm Output Options 9A

    If there are 10 invalid cards or 10 incorrect PINs within 10 minutes, the keypad will lock for 10 minutes If you use an MLB2 as a Wiegand reader, you can set the ID of your device for recognition. When you insert or the alarm and internal bell will be active for 10 minutes depending on the option selected.By default,...

  • Page 11: Connections

    06. CONNECTIONS DESCRIPTION OF THE MAIN CABLE Line Sequence Marks Color Function description Blue NO Relay Orange NC Relay Purple Common Relay Power Input 12Vdc (Input + DC) One end of the output button (Output button of the other OPEN Yellow end connected GND) D_IN...

  • Page 12: Connection Scheme - Power Supply 11A

    12Vdc 3A 12Vdc 3A máx Blue PUSH Orange Purple 12Vdc + Yellow OPEN Power Supply 12Vdc 5A Brown D_IN Gray ALARM Green White Black EF30 MLB2 12Vdc 5A máx EF380 12Vdc 5A máx Controller Bell Magnetic 24Vdc 20A máx Exit Switch...

  • Page 13: Connection Scheme - Mlb2 For Another Mlb2 13A

    06. CONNECTIONS CONNECTION SCHEME - MLB2 FOR ANOTHER MLB2 EF30 EF30 12Vdc 3A max 12Vdc 3A max EF380 Power Supply EF380 12Vdc 3A max 12Vdc 5A 12Vdc 3A max Blue Blue Orange Orange Purple Purple 12Vdc + 12Vdc + 12Vdc +...

  • Page 14: Troubleshooting

    06. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS / SPECIALIZED INSTALLERS 1. Check whether a finger or fingerprint sensor is stained with sweat, water, or dust 2. Retry after wiping off finger and fingerprint sensor with dry paper tissue or a mildly wet FINGERPRINT CAN NOT BE READ OR IT TAKES TOO LONG cloth.

Table of Contents