Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Blue Diamond Multi-Purpose Cutter
Summary of Contents for Blue Diamond Multi-Purpose Cutter
- Page 1 Multi-Purpose Cutter Operation and Parts manual...
- Page 3 I have read, understand, and take responsibility for the use of this attachment. I understand and accept responsibility for the proper use of this cutter. I acknowledge this cutter is dangerous if not used correctly or if the safety information is not followed. Date__________________ Owner’s Signature_________________________________________ Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
-
Page 4: Table Of Contents
Operation Checklist ..... 26 Right of Way (Roadway) Mowing ..26 Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 5: Introduction
1.3 Intended Usage stationary object is contacted. A shear key in the input shaft protects the motor from damage. Do not use this Multi-Purpose Cutter for any other purpose than its intended use; cutting grass, weeds, WARNING and light brush and an in-line or offset application. -
Page 6: Owner/Operator Manual Storage
1.6 Serial Number Location The Multi-Purpose Cutter can also be used in a vertical configuration for mowing along hedge rows The serial number decal is located on the top left and tree lines. of the mounting plate. This unit WILL NOT work on a skid steer Model Number ______________________________ machine. -
Page 7: Safety
As you hazards. assemble, operate, or maintain the Multi-Purpose Cutter Hazards are identified by the “Safety Alert Symbol” (unit), you must be alert to potential hazards. You and followed by a signal word such as “DANGER”,... -
Page 8: Safety Icon Nomenclature
Stop engine Crush hazard STOP Crush hazard (chock Think safety THINK SAFETY! wheels) Transmission in park Crush hazard (foot) Use proper support Defective or broken part Use proper tools Entanglement hazard Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 9: General Safety Instruction
To prevent personal injury or even death, be sure you read and understand If the Multi-Purpose Cutter has been altered in any all of the instructions in this manual and other way from the original design, Trailblazer does not related OEM equipment manuals! The accept any liability for injury or warranty. -
Page 10: Training
If you do not understand any information in this hearing loss. manual, see your dealer or contact Blue Diamond Attachments, LLC before proceeding. Hearing loss from loud noise is cumulative over a lifetime without hope of natural recovery. -
Page 11: Federal Laws And Regulations
Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102). Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 12: Sign-Off Form
2.8 Sign-Off Form Blue Diamond Attachments, LLC follows the Make periodic reviews of SAFETY and OPERATION of the cutter a standard practice. An untrained operator is general Safety Standards specified by the Farm Equipment Manufacturers Association (FEMA), and not qualified to use this cutter. -
Page 13: Operation Safety
Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 14: Safety Signs And Instructional
5. Replacement parts must have replacement labels attached during installation and/or before the cutter is used. 6. Labels are available from your authorized dealer or from Trailblazer at no charge. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 15: Safety Signs
3.3 Safety Signs Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... - Page 16 Stop engine, set brake and wait for all moving parts to stop before dismounting. • Support mower securely before working beneath unit. • Transport with clean reflectors, SMV and working lights as required by federal, state, and local laws. TI-00005 Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 17 Do not operate with bystanders in mowing area. WITH U.S. & IMPORTED PARTS • Do not operate with deflectors/guards removed. TI-00008 • Do not place hands or feet under deck. TI-00007 WARNING NO RIDERS TI-00074 Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
-
Page 18: Operation
Burning material, sparks, and coals could be thrown from the cutter to areas of vegetation that might ignite. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 19: Tractor Requirements
Operating the cutter with a tractor that does not meet the following requirements may cause tractor or cutter damage and be a potential danger to the operator and passersby. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 20: Mowing Configuration
The return hose must have free-flow back into the pump reservoir and not be ported through the tractor’s manifold valve. DO NOT connect into the tractor’s rear remote return valve. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... - Page 21 5. Remove the left-side clip and t-handle retaining pin. 2. Disconnect both the supply and return hoses to the cutter. 3. Place the ends of the hoses in a place they will not be contaminated by dirt. Continued... Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 22 7. Push the left side of the cutter deck back towards the tractor. 10. Replace the right-side t-handle retaining pin and clip. 8. Pull the cutter deck to the side of the tractor. Continued... Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 23 11. Replace the left-side t-handle retaining pin and clip. 12. Reconnect the hydraulic hoses. 13. Position the cutter deck on the ground. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
-
Page 24: Mowing Configuration
5. The cutter deck can be positioned in four slanted configurations depending on the mowing application. 3. Replace both t-handle retaining pins and clips. Reconnect the hydraulic hoses. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 25: Detaching From Tractor
After 1/2 hour of operation: Tighten all fasteners if necessary. Lubricate all grease fittings. b. After 10 hours of operation: Go to the normal servicing and maintenance schedule, as defined in the Maintenance Section. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 26: Operation Checklist
2. Cutter sections or wings are adjusted to be close and parallel to the ground without exposing the blades. 3. Mowing area has been inspected and foreign materials and debris have been removed. 4. Passersby are inside an enclosed vehicle. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 27: Transporting
When traveling below the posted speed limit, The tractor should be equipped with a keep to the right and yield the right-of-way to Roll Over Protective Structure (ROPS) allow faster traffic to pass. and a seat belt. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 28: Storage
4. Lubricate all grease points. Make sure all grease cavities have been filled with grease to remove any water residue from washing. 5. Touch up all paint nicks and scratches to prevent rusting. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 29: Service And Maintenance
Trailblazer will not accept responsibility for damages as a result of the use of unapproved parts. Safety Shields and Devices When completing a maintenance or service function, make sure all safety shields and devices are installed before placing the cutter in service. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 30: Greasing
Use care not to strike the nut or the end of the shaft. 4. Retighten the nut to 700 ft. lbs. Install the cotter pin and spread the tangs. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 31: Service Record
Repairs or modifications to the cutter can result in serious injury or death should these repairs fail. NOTICE Anyone performing a welding repair should be certified in accordance with the American Welding Society (AWS) standards. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... -
Page 32: Parts
8. Parts Breakdown Replacement parts are available from your authorized Dealer Parts Department. Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020... - Page 33 44" 32" 503820 503821 503202 Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 34 8. Parts breakdown (Continued) Replacement parts are available from your authorized Dealer Parts Department. 44" Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 35 44" Skid steer mount (shown) John Deere 400/500 mount (not shown) Euro-Ag/Global mount (not shown) Euro-Ag/Global mount (not shown) Swing arm Brush Cutters Blue Diamond Attachments, 888-376-7027 LLC September 2020...
- Page 36 8. Parts breakdown(Continued) Replacement parts are available from your authorized Dealer Parts Department. 32" Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 37 32" Skid steer mount (shown) John Deere 400/500 mount (not shown) Swing arm Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
-
Page 38: Warranty
Nothing herein shall limit the right of Purchaser or Blue Diamond Attachments, LLC (or the right of any permitted successor or assign of either) to bring proceedings against the other in the courts of any other jurisdiction wherein any assets of such other party may be located. - Page 39 WARRANTY REGISTRATION FORM Multi-Purpose Cutters THIS REGISTRATION FORM MUST BE ON FILE WITH BLUE DIAMOND ATTACHMENTS, LLC WITHIN 30 DAYS OF DELIVERY TO PURCHASER, OR WARRANTY CLAIM WILL NOT BE HONORED. PLEASE RETURN COMPLETED FORM BY E-MAIL, FAX, OR MAIL: E-MAIL: warranty@bdattachments.com...
- Page 40 NOTES Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
- Page 41 NOTES Brush Cutters Blue Diamond Attachments, LLC 888-376-7027 September 2020...
Need help?
Do you have a question about the Multi-Purpose Cutter and is the answer not in the manual?
Questions and answers