Emist EPIX360 Technical Manual
Electrostatic sprayer
Hide thumbs
Also See for EPIX360:
- Manual (45 pages) ,
- User manual (12 pages) ,
- Quick start manual (2 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Emist EPIX360
Summary of Contents for Emist EPIX360
- Page 1 E P I X 3 6 0 T E C H N I C A L M A N U A L V E R . 0 1 0 6 2 1...
- Page 2 Each component has been inspected prior to your purchase. However, in the event that there is a problem, please contact our customer care center at Emist.com. EPIX360™ Electrostatic Sprayer Technical Manual ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621...
- Page 3 E. NO RESELLER WARRANTY: The reseller makes no warranty of its own and the reseller has no authority to make any representation or promise on behalf of EMist, or to modify the terms or limitations of this warranty in any way.
-
Page 4: Table Of Contents
Section 4 - Tank Liner Procedures Page 13 Section 5 - Before Reassembly Page 13-14 Section 6 - System Reassembly Page 14-15 ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... -
Page 5: Section A - Internal Mechanics Schematics Illustration
EPIX360 - Technical Manual Section EPIX360 Internal Mechanics Technical Schematic System Pieces and Part Numbers Itemized list on next sheet ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... -
Page 6: Section B - Schematics Itemized Parts List
MD.03.056 Left & Right Handle Conductive Grips MD.03.055 Left & Right Wand Halves MD.03.057 Wedge Cap Fan Cover MD.03.058 Silicone Protective Cover ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... -
Page 7: Section 1 - Battery
2. If “RED” Indicator light stays on, this means the battery is fully charged. If the “RED” indicator light blinks fast, this indicates the battery is not secure to the charger. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... -
Page 8: Section 2 - Disassembly Procedures
To remove battery: Press down on release tab, then slide battery out from unit. Section Disassembly Procedures Removal of EPIX360 Frame Silicone Sleeve (Pt. #MD.03.058). ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... - Page 9 2 halves of the pastic body Remove (2) T8 Torx meet. Star Screws (Pt. #HW.00.253) from main EPIX360 unit front nozzle assembly. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621...
-
Page 10: Section 3 - Main Customer Quality Issues
2.) The tank check valve release (female valve release-tank cap - (Pt. #SA.2011.1) & (male valve) Female check valve release-tank cap Pt. #SA.2011.1 Male check valve release ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... - Page 11 EPIX360 unit back together again. Locate far left Disconnect connector of trigger connector of trigger switch, remove suspect trigger switch. switch, replace with new part. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621...
- Page 12 Female check valve release-tank cap Pt. #SA.2011.1 Remove tank cap by gently pulling component away from tank cap cover. Replace with new ordered tank cap assembly. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621...
-
Page 13: Section 4 - Tank Liner Procedures
Check all connectors are secure to plugs and to main control board and HVPS board. b.) Check connections of ground wires and wiring to main battery terminals. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... -
Page 14: Section 5 - Before Reassembly
4.) Replace tank back clip and tank lock on top of EPIX360 unit. 5.) Make sure the fan cover (Pt. #MD.03.057) bevel is in the downward position before installation. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621... - Page 15 The Nozzle Assembly (Pt. #MD.03.047). Take a ½” deep socket wrench, place over the nozzle and adjust mist to one’s desired flow. ©2021 EMist® is a registered trademark of SanoTech 360, LLC. All rights reserved. EMist-00135-20-EPIX360 Technical Manual - 010621...