Summary of Contents for Feig Electronic OBID ID RW02.ABCD-A
Page 1
Montageanleitung / Mounting Instruction ID RW02.ABCD Version: -A / -B Version: -AL / -BL (Leser mit Gehäuse) (Leser ohne Gehäuse) (Reader with Case) (Reader without Case) (deutsch / english) M60491-8de-ID.DOC...
Page 2
Identifikation System OBID deutsche Version ab Seite 3 english version from page 13 Seite 2 von 22 FEIG ELECTRONIC GmbH...
Page 3
Da sich Fehler, trotz aller Bemühungen nie vollständig vermeiden lassen, sind wir für Hinweise jederzeit dankbar. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung dafür, dass die in diesem Dokument enthaltenden Informa- tionen frei von fremden Schutzrechten sind. FEIG ELECTRONIC GmbH erteilt mit diesem Dokument keine Lizenzen auf eigene oder fremde Patente oder andere Schutzrechte.
Nachmessen sicherzustellen, dass das Gerät spannungslos ist. • Das Verlöschen einer Betriebsanzeige ist kein Indikator dafür, dass das Gerät vom Netz getrennt und spannungslos ist. Bei Arbeiten am geöffneten Gerät ist zu beachten, dass evtl. spannungsführende Teile freiliegen. FEIG ELECTRONIC GmbH Seite 5 von 22...
2.2 ID RW02.ABCD-AL / -BL 1 x ID RW02.ABCD -AL oder -BL 1 x Montageanleitung 3. Reihenfolge der Montage Anschluß nach Tabelle 1 und Bild 1, 2, 3 Wandmontage Inbetriebnahme Klarsichtdeckel montieren Aufkleber montieren Seite 6 von 22 FEIG ELECTRONIC GmbH...
Leser mit RS232 Schnittstelle werden nach dem in Bild-3 dargestellten Schema mit dem Leitrech- ner verbunden. Leitrechner gelb / 8 grün / 7 ID RS02 blau / 4 Bild 3: RS232 Anschluß ID RW02.ABCD-A / -AL Seite 8 von 22 FEIG ELECTRONIC GmbH...
Schrauben direkt auf eine solche Schalterdose geschraubt werden. Ist eine Montage auf einer Metalloberfläche notwendig, kann zur Einhaltung des Mindesabstandes der Gehäuserahmen ID APG-A von FEIG ELECTRONIC bezogen werden. Hinweis; Nach Abschluß der Klemm- und Montagearbeiten und noch vor der Befestigung des Auf- klebers sollte die Funktion getestet werden! 5.2 ID RW02.ABCD-AL/ -BL:...
Alle Leser zeigen mit der gelben Farbe der LED ihre Funktionsbereitschaft an. Voraussetzung ist, daß die Anzeige der Signalgeber in der Werkseinstellung bleibt und die Eingänge geöffnet sind. Eine vollständige Funktionskontrolle ist nur mit einem Terminal bzw. einem Leitrechner möglich. Seite 10 von 22 FEIG ELECTRONIC GmbH...
60,0 mm 13,5 mm 3,5 mm 3,5 mm Gehäuseöffnung für LED und DIP 47,0 mm 80,0 mm 18,0 mm 15,5 mm Bild 5: Abmessungen ID RW02.ABCD-A /-B Bild 6: Abmessungen ID RW02.ABCD-AL /-BL FEIG ELECTRONIC GmbH Seite 11 von 22...
• Adresse des DIP-Schalters 0 (wird priorisiert, wenn Adresse im EEPROM = 0) • Eingang 1 aktiviert LED rot und das Relais • Eingang 2 aktiviert LED grün und den Summer • LED-Betriebsanzeige gelb Seite 12 von 22 FEIG ELECTRONIC GmbH...
Page 13
Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information.
Page 14
5. Installation: ........................19 5.1 ID RW02.ABCD-A / -B:......................19 5.2 ID RW02.ABCD-AL/ -BL: .....................19 6. Operation: ........................20 6.1 Setting the Addresses ......................20 6.2 Function Control .........................20 7. Dimensions........................ 21 8. Technical Data......................22 Page 14 of 22 FEIG ELECTRONIC GmbH...
Please switch off the power supply before opening the device and make sure that it is idle. The fact that an operational display goes out does not necessarily mean that the device is disconnected from the power supply and idle. FEIG ELECTRONIC GmbH Page 15 of 22...
1 x installation instructions 3. Respect the order of the installation: 1. connection according to table 1 and figure 1, 2 2. wall-installation 3. operation test 4. attaching the transparent top 5. fixing the adhesive label Page 16 of 22 FEIG ELECTRONIC GmbH...
Readers with RS232 interface have to be connected to the host according to fig 3: connection of the RS232-interface". Host yellow / 8 green / 7 Reader blue / 4 fig 3: connection of the RS232-interface Page 18 of 22 FEIG ELECTRONIC GmbH...
- the transponder should be hold area-parallel to the antenna. The distance between the reader antenna to conducting materials should be of minimum 3 cm. Otherwise, the reading range will be decreased. FEIG ELECTRONIC GmbH Page 19 of 22...
An orange coloured LED (all readers) indicates : ready to operate / waiting. A requirement for this is that the indicator-configuration has not been modified and that all inputs are open. A complete function control can only be carried out with a terminal res. central PC. Page 20 of 22 FEIG ELECTRONIC GmbH...
0 (preferred if EEPROM address > 0) • DIP-switch address: 0 (preferred if EEPROM address = 0) • input 1 activates LED red and relay • input 2 activates LED green and buzzer • LED operation control orange Page 22 of 22 FEIG ELECTRONIC GmbH...