Page 2
® Identifikation System OBID deutsche Version ab Seite 3 english version from page 12 Seite 2 von 20 FEIG ELECTRONIC GmbH...
Page 3
Da sich Fehler, trotz aller Bemühungen nie vollständig vermeiden lassen, sind wir für Hinweise jederzeit dankbar. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung dafür, dass die in diesem Dokument enthaltenden Infor- mationen frei von fremden Schutzrechten sind. FEIG ELECTRONIC GmbH erteilt mit diesem Dokument keine Lizenzen auf eigene oder fremde Patente oder andere Schutzrechte.
Nachmessen sicherzustellen, dass das Gerät spannungslos ist. • Das Verlöschen einer Betriebsanzeige ist kein Indikator dafür, dass das Gerät vom Netz getrennt und spannungslos ist. Bei Arbeiten am geöffneten Gerät ist zu beachten, dass evtl. spannungsführende Teile freiliegen. FEIG ELECTRONIC GmbH Seite 5 von 20...
Leser der ID RW-Familie“) der Stromsparmodus des Lesers aktiviert werden. Zum Aktivieren des Stromsparmodus ist der Eingang IN1 auf GND (X1 Pin 1) des Lesers zu legen. Eine Beschaltung mit Fremdspannung kann zur Zerstörung des Lesers führen. Seite 6 von 20 FEIG ELECTRONIC GmbH...
Für den Selbstbau einer Antenne gelten folgende Grenzwerte: Größe max. 200 x 200 mm Material für Antennenspule Kupferlackdraht Drahtstärke der Antennenspule 0,2 ... 0,4 mm 490 µH ± 2% Induktivität 3...8 Ω Widerstand Zuleitungslänge max. 2 m (verdrillte Leitung) FEIG ELECTRONIC GmbH Seite 7 von 20...
Vor Einbauten in Metallwänden oder -gehäuse halten Sie unbedingt Rücksprache mit dem Hersteller. 4. Inbetriebnahme Der Leser verfügt über keine Bedien- und Anzeigeelemente. Der Leser kann zur Anpassung an die individuellen Einsatzbedingungen über die RS232 Schnittstelle konfiguriert werden (siehe: „System-Handbuch Standard-Leser der ID RW-Familie“) Seite 8 von 20 FEIG ELECTRONIC GmbH...
RS232-TTL RS232 (V24) RS232-TTL Tabelle 4-1: Funktion der Brücken zur Schnittstellenkonfiguration Funktion RS232 V24 22Ω 0Ω 0Ω RS232-TTL 0Ω 0Ω Tabelle 4-2: Brückenstellung für Schnittstellenkonfiguration Bild 4-1: Lage der Brücken auf der Lötseite FEIG ELECTRONIC GmbH Seite 9 von 20...
• EEPROM 10.000 Schreibzyklen ID RW01-A • Serielle Schnittstellen 1 x RS232 (V24) 1 x Daten-/Takt (Wiegand- oder Omron-Emulation) ID RW01-B • Serielle Schnittstellen 1 x RS232-TTL 1 x Daten-/Takt (Wiegand- oder Omron-Emulation) Seite 10 von 20 FEIG ELECTRONIC GmbH...
Montageanleitung ID RW01...-A / -B 6.1 Anhang B: Abmessungen 90,0 mm 87,5 mm 45,0 mm 2,5 mm Befestigungsbohrungen d=3.0mm Antennenspule bestückter Bereich 14,0 mm 77,0 mm bestückter Bereich FEIG ELECTRONIC GmbH Seite 11 von 20...
Page 12
Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information.
Page 13
2.3 Connection of an external antenna: ................16 3. Installation: ........................17 4. Operation: ........................17 5. Configuration of the RS232 Interface (from PCB-version FE 437): .......18 6. Annex A: Technical data ...................19 6.1 Annex B: Dimensions....................... 20 FEIG ELECTRONIC GmbH Page 13 of 20...
Please switch off the power supply before opening the device and make sure that it is idle. The fact that an operational display goes out does not necessarily mean that the device is disconnected from the power supply and idle. Page 14 of 20 FEIG ELECTRONIC GmbH...
Readers" the power saving mode of the reader can be activated. To activate the power saving mode input IN1 must be connected to GND (X1 Pin 1) of the reader. The connection of extraneous voltage might damage the reader. FEIG ELECTRONIC GmbH Page 15 of 20...
Before installing the reader in metal-walls or metal casings please discuss the procedure with the manufacturer. 4. Operation: The reader has no operating or indicating elements. It can be configured according to the individ- ual conditions by the RS232 interface (see: "System Manual - Standard-Reader ID RW-Family"). FEIG ELECTRONIC GmbH Page 17 of 20...
10.000 write-cycles ID RW01-A • serial interfaces 1 x RS232 (V24) 1 x data/clock (Wiegand- or Omron emulation) ID RW01-B • serial interfaces 1 x RS232-TTL 1 x data/clock (Wiegand- or Omron emulation) FEIG ELECTRONIC GmbH Page 19 of 20...