Page 1
Product reference : 90-60-244 white / 90-60-256 black USER GUIDE INSTALLATION GUIDE REV : 1 – marine electronics Z.I. Kerandré – Rue Gutenberg – 56700 HENNEBONT- FRANCE http://www.nke.fr – After sale service n° 0 892 680 656.
3.6 C NMEA ....24 ONNECTION TO THE OPLINE BUS AND TO THE BUS OF THE INSTALLATION 3.7 I ................... 24 DENTIFICATION OF THE CABLE WIRES 3.8 TL25 ................. 25 AND REMOTE CONTROL INITIALIZATION - 2 – TL25 User guide–- 33-60-021-000...
Alarm signal Unit installation and displays all the channels available on the bus. The TL25 is controlled using either a cable remote control or a radio remote control (not included with the product). - 3 – TL25 User guide–- 33-60-021-000...
Page 4
KNOTS APP WIND A 105- DEGRES DEPTH 10.50 METERS input NMEA NMEA + NMEA - log depth interface 90-60-450 Cable TOPLINE 20-61-001 DATA black 12VDC white connecting box 90-60-417 depth speedomètre Figure 1 - 4 – TL25 User guide–- 33-60-021-000...
Cross-track error Please note that the channels MAX SPD and AVERAGE SPD can be accessed when the TL25 is master. In this case, these channels are displayed alternatively on one single screen. By default, this channel is calculated using the surface speed, and in the absence of the latter it will be calculated using the bottom speed.
1.3 Keypad functions of the remote control Press this key to select one of the three display screens of the TL25. The selected screen flickers. Low key and High key These keys allow to select a different channel to the one already displayed. They also allow to increment or decrement a data which is in the process of being modified.
1.4.2 List of channels displayed The master display, whether it is the TL25 or any other TOPLINE display, and each TOPLINE sensor, automatically create their respective channels when they are connected to the TOPLINE bus. You will find the list of created channels in annex 1.
CAUTION : if your installation is equipped with several TOPLINE displays, make sure that the remote control controls the display which you wish to operate. Press the repeatedly, until the intended display flickers. - 8 – TL25 User guide–- 33-60-021-000...
Page 9
Release. Using the keys select YES VALID ALARME Validate by maintaining pressure on the key After 5 s, the TL25 automatically exits the setting mode Figure 4 - 9 – TL25 User guide–- 33-60-021-000...
Using the key set the new filtering value 10 TL 25 Validate and exits the menu by maintaining a pressure un key BOAT SPEED 16.85 The new filtering value is saved in memory Figure 5 - 10 – TL25 User guide–- 33-60-021-000...
0 = no lighting, 1 corresponds to the minimum level of lighting and 4 to the maximum level. You have the option to set the level of lighting, either on the TL25 only, or on every TOPLINE display of your installation : 1.8.1 TL25 setting procedure...
Validate and exit the setting by maintaining the pressure on BOAT SPEED 31.20 The new unit is saved to the memory. In approximataly 5 or 6 km/h seconds, display will revert to value. Figure 7 - 12 – TL25 User guide–- 33-60-021-000...
TL 25 TRIP LOG Press the key and hold (approx 1805 6 sec) to set " 0" MILES TL 25 TRIP LOG The trip log is set to " 0" MILES Figure 9 - 13 – TL25 User guide–- 33-60-021-000...
1.11 Choice of languages You can configure the TL25 in one of these six available languages : French, English, Italian, Spanish, German and Dutch. TL 25 BOAT SPEED 16.85 NOEUDS APP WIND A Using the keys DEGREES COMPAS HEAD 274°...
− the message T2 setting appears, − change the value of T2 using the arrow keys, then confirm with the − after 5 seconds, the TL25 will automatically leave the setting mode. - 15 – TL25 User guide–- 33-60-021-000...
The other dimensions are rounded to the nearest unit (ex : degrees for angles). A frame can be partially empty between commas. The TL25 will take the missing data in another frame (ex : speedometer in VWH and compass in HDG).
Page 17
1.13.4 Frames identified by the TL25 NMEA Description TOPLINE channels created Frame LAT_DEGMIN, LAT_MILMIN, LON_DEGMIN, $xxGLL Latitude, longitude, time and quality index LON_MILMIN. LAT_DEGMIN, LAT_MILMIN, LON_DEGMIN, $xxGGA Latitude, longitude and time LON_MILMIN. $xx-ZDA ANNMOIS, HEUJOUR, MINSEC. Date and time Latitude, longitude, date, time, SOG, COG $xxRMC ANNMOIS, HEUJOUR, MINSEC.
The address of the remote control is lower than that of the TL25 : reinitialise the remote control, see chapter 17. The TL25 is set at the address « 0 » : perform its initialization, see chapter 17. The TL25 displays the message « data wire error »...
2 SENSOR CALIBRATION Every nke sensor is adjusted at the factory. However, a calibration is required to adapt the sensor to the specificities of your boat and to obtain an optimum measurement accuracy. Follow the calibration procedure below, by visualising the settings on a display.
* For the previous generation of compass, referenced as 90-60-005, at least three circles must be executed. In case of problem during autocompensation, the TL25 displays the PAN message , plus one code : Code 1 : cancellation at user request.
− more than 1 meter away from a VHF radio transmitter. The best readability of the TL25 is generally obtained by mounting it on a bracket. You can also wall mount it on any flat surface of the boat. Four M4x30mm fixing screws are provided with the TL25.
3.4.2 Mounting procedure of the TL 25 on the bracket introduce the cable in the ∅18 drilled hole, position the TL25 so that it faces the four ∅4 holes, place the four screws (provided with the product) in the holes, from the back of the partition, tighten the four fixing screws moderately.
Lay a very thin silicone sealing joint around the mounting perimeter, introduce the cable in the ∅18 drilled hole, position the TL25 so that it faces the four ∅5 holes, place the four screws (provided with the product) in the holes, from the back of the partition, tighten the four fixing screws moderately.
3.6 Connecting the Topline bus and the NMEA connection Make the bus cable run from the TL25 to the TOPLINE terminal box of your installation. Connect the bus cable inside the terminal box. TL 25 BOAT SPEED 16.85 NOEUDS APP WIND A...
3.8 TL25 and remote control initialization At first power-up, you must initialize the TL25 so that an address is assigned to it. The display is delivered with the address set as 0. During the initialization, it will automatically insert itself in the list of instruments and displays of the TOPLINE bus of your installation : −...