Aerohive AP350 Installation Manual

Aerohive AP350 Installation Manual

Directional antenna
Hide thumbs Also See for AP350:

Advertisement

AP350 5-GH
I
NSTALLATION
This guide explains how to install an Aerohive AP350 5-GHz directional point-to-point antenna and connect it
to an AP350 access point. The AH-ACC-350-ANT-5 is an indoor dual-band lightweight antenna that is well
suited for applications where a 120° H-plane and a 70° E-plane are optimal. These antennas are typically
corner-mounted in pairs, facing each other and with no obstructions between them. This antenna can also
be used as a point-to-multi-point expansion device with a wide azimuth.
For the latest product documentation, compliance information, and software updates, visit
www.aerohive.com/support.
K
C
, R
IT
ONTENTS
EQUIRED
The AP350 5-GHz directional antenna kit includes the following items:
AP350 5-GHz 5-dBi antenna (Aerohive part number AH-ACC-350-ANT-5)
(4)1.25" x 1/8" (32 mm x 3 mm) cross-head screws
(4) 1.25"" (32mm) drywall and concrete wall anchors
To install this antenna, you will need the following accessories and tools:
Cross-head screwdriver, drill with a 1/8" (32mm) bit, and hammer
RF test meter for 5-GHz devices
S
I
AFETY
NSTRUCTIONS AND
Read and follow these safety instructions and hazard warnings before installing this antenna. Keep these
instructions for future reference.
To comply with radio frequency exposure limits, do not place this antenna within 26" (65 cm) of people.
To install this antenna, you must be a qualified installation professional, licensed or certified in
accordance with local regulations.
Use only attachments and accessories specified by Aerohive.
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. During installation, exercise extreme care not to
come into contact with these circuits, which can cause serious injury or death. For proper installation
of the product, refer to national and local electrical codes: NFPA (National Fire Protection
Association) 70, National Electrical Code Article 810 (U.S.); Canadian Electrical Code, Part I, CSA 22.1
and Section 54 (Canada); and if local or national electrical codes are not available, refer to IEC
(International Electrotechnical Commission) 364, Part 1 through 7 (other countries).
Do not connect or disconnect antennas or cables from the AP350 during periods of lightning activity.
© 2012 Aerohive Networks, Inc.
All rights reserved.
P/N 330077-01
D
Z
IRECTIONAL
G
UIDE
A
CCESSORIES
S
H
ITE
AZARD
A
NTENNA
,
T
AND
OOLS
W
ARNINGS
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AP350 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aerohive AP350

  • Page 1 NSTALLATION UIDE This guide explains how to install an Aerohive AP350 5-GHz directional point-to-point antenna and connect it to an AP350 access point. The AH-ACC-350-ANT-5 is an indoor dual-band lightweight antenna that is well suited for applications where a 120° H-plane and a 70° E-plane are optimal. These antennas are typically corner-mounted in pairs, facing each other and with no obstructions between them.
  • Page 2 IRECTIONAL NTENNA To provide unobstructed RF coverage, mount the AP350 antenna so that it has at least a three-foot (one-meter) clearance from any nearby obstructions. For best coverage, these antennas are typically installed in pairs, directly facing each other, and with no obstructions between them.
  • Page 3 Connecting the Antenna to the AP350 Connect each of the three antenna cables to a 5-GHz jack on the AP350, as shown in the illustration below. You can use 2.4 GHz antennas in addition to the 5-GHz directional antenna. Always install a 50-Ohm load terminator on any unused antenna connector.
  • Page 4 AP350 5-GHz Directional Antenna Installation Guide...

Table of Contents