1. Manuals
  2. Brands
  3. Motion Impossible Manuals
  4. Robotics
  5. AGITO
  6. User manual

Motion Impossible AGITO User Manual

Hide thumbs Also See for AGITO:
Table of Contents

Advertisement

Quick Links

Download this manual
AGITO
User Manual
AGITO OS Nova (5.00)
April 2021

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AGITO and is the answer not in the manual?

Questions and answers

Related Manuals for Motion Impossible AGITO

Summary of Contents for Motion Impossible AGITO

  • Page 1 AGITO User Manual AGITO OS Nova (5.00) April 2021...

  • Page 2: Document Revision History

    REVISION: DATE: DESCRIPTION: July 2019 Initial Document Release – Firmware Release r3.0 September 2019 Updated for AGITO Tower – Firmware Release r3.2 Minor revisions and corrections October 2019 Updated for AGITO Trax – Firmware Release r4.0.4 1.2rev1 October 2019 Updated for AGITO Trax – Firmware Release r4.0.4...
  • Page 3 Batteries, Charging & Storage Throttle Input Warranty & Service Sports & Trax Mode General Specifications Menu Navigation AGITO Core v1.1 (Diode Board enabled) Speed Limit AGITO Master v1.0 Sports & Trax Mode AGITO Tower v1.0 Menu Navigation AGITO Mains PSU v2.0...
  • Page 4 RF MODULE & COMMUNICATIONS SETTINGS Y-cord pedal splitter: Tower only control (Sports) Attaching Camera Mounts Changing Settings V-Con PRO: Attaching to AGITO RF Power V-Con PRO: Adjustment and Tuning RF Forward Error Correction (FEC) AGITO User Manual OS 5.0 Nova IV - Index www.Motion-Impossible.com...
  • Page 5 MAINS POWER SUPPLY UNIT (PSU) Overview Required before use I/O Ports and Current limits Battery attachment Attaching PSU to Trax Drive-end FIRMWARE UPDATES How to update Firmware: MAINTENANCE Sports Drive-end Sports Drive-end: Steering Linkage www.Motion-Impossible.com V - Index AGITO User Manual OS 5.0 Nova...
  • Page 6 Motion Impossible Limited reserves the right to revise this User Manual and make changes from time to time without obligation to notify any persons of such revisions or changes. In no event shall Motion Impossible Limited, its employees or authorised agents be liable for any damages or losses, direct or indirect, arising from the use of any technical or operational information contained in this document.

  • Page 7: General Safety

    • It is your responsibility to perform a full system check of AGITO prior to every use. • The operator must have control of all people, animals, vehicles, vessels and structures in close proximity of the AGITO when in use.

  • Page 8: General Specifications

    AGITO uses RF modules that can be user configured. It is the owner’s responsibility to ensure that the correct settings are used for the territory that the RF system is being used in. By using AGITO, you acknowledge that you have read, understand, and agree to this disclaimer. You agree that you are solely responsible for your conduct while using AGITO and for any direct or indirect consequences that may result from its use.
  • Page 9 TRAINING AND FURTHER ASSISTANCE » AGITO Academy offers a full range of training for the AGITO Modular Dolly System, online through video guides and our support website as well as face-to-face training, see “AGITO Academy” on page 52. Throughout this manual, web links to online training, our support website and knowledge base are show as follows: ��...
  • Page 10 32 Kg Sports Drive-ends 21.5 x 32 x 17 inches 70.5 lbs Item: Part Name: 2x AGITO Sports Drive-ends 4x Wheel Nuts Wheel Nut Spanner 4x Suspension Lock-out Bars www.Motion-Impossible.com 5 - Case Contents AGITO User Manual OS 5.0 Nova...
  • Page 11 Power Pass-through Cable Set / Fibre Optic Tails* Pedals* Gas-Struts (under tower) TOWER MUST BE FULLY LOWERED AND THE GAS- STRUT REMOVED PRIOR TO PACKING. * exact case content subject to ordered specification AGITO User Manual OS 5.0 Nova 6 - Case Contents www.Motion-Impossible.com...
  • Page 12 Case ID: Dimension (HxWxD) Shipped Weight: 170x460x350mm / 7x18x14 inches 10.5Kg / 23lbs Item: Part Name: AGITO PSU Battery Module Battery Module - PSU Cable (under PSU in case) www.Motion-Impossible.com 7 - Case Contents AGITO User Manual OS 5.0 Nova...

  • Page 13: Main Power Switch

    AGITO » SYSTEM OVERVIEW: AGITO CORE » INTRODUCTION The Core is the heart of your AGITO Modular Dolly System, within this module is contained all of the power management, RF / Communications and Steering drivers. » DIMENSIONS See “Technical Drawings” on page 66 »...
  • Page 14 AGITO Sports Drive-ends are our free-roaming drive module, with multiple wheel-type options. Designed for speeds of upto 32mph with additional hardware and future firmware update. AGITO Sports will operate at 5.8 m/s (12.1mph) with Dolly Wheels in Standard Operator Mode (SOM). See “Specifications” on page 64 »...

  • Page 15: Key Features

    AGITO TRAX DRIVE-ENDS » AGITO Trax Drive-ends are designed to enable the use of 300-409mm (12 – 16 inch) dolly track with the AGITO system. AGITO Trax will operate at 3.1m/s (7mph), see “Specifications” on page 64 » DIMENSIONS See “Technical Drawings” on page 66 »...
  • Page 16 (ARRI SRH-3, Shotover G1, Newton, Freefly Movi, DJI Ronin) The device is powered via a V-lock battery plate located on the base plate. It is also possible to operate AGITO Tower as a stand-alone unit, when paired with the AGITO Hub using an optional upgrade.

  • Page 17: Control Functions

    AGITO » SYSTEM OVERVIEW: MASTER CONTROLLER » INTRODUCTION The Master Controller is the manual input device for your AGITO Modular Dolly System. » OPERATIONAL LAYOUT Speed Dial Steering Mode Switch Steer Limit Acceleration Dial Steering Input Throttle Input Function Switch...

  • Page 18: Function Switch

    SPORTS MODE This switch is set to Emergency Brake, switching this during operation will command the AGITO to stop as quickly as possible and hold the AGITO in position. There are two modes of operation, UP & DOWN, these are explained later in the manual, see “E-Stop” on page 51.

  • Page 19: Mode Switch

    • AUX 2: Reserved for Firmware Updates only (see Firmware update section of this manual) • ETHERNET PORT: For Future Use » POWER Turns the Master Controller On and Off AGITO User Manual OS 5.0 Nova 14 - System Overview www.Motion-Impossible.com...

  • Page 20: Menu Navigation

    RECOMMENDED. ALWAYS RESOLVE THE ISSUE BEFORE CONTINUING WITH THE USE OF AGITO. OVERVIEW » Navigation of the AGITO OS is based on a simple menu structure: Top-Level Menu, Connection Screen, Home Screen, and Settings, as outlined below. As new features become available, additional screens will be activated. Splash Screen...

  • Page 21: Top Level Menu

    After the splash screen, which displays OS version number and the Master Controller serial number, the Top-level menu will be displayed. This screen enables the user to select the operational mode that the AGITO should start up in, at this time the three modes are: SPORTS - see “Sports Mode”...

  • Page 22: System Settings

    This features enables the user to manually offset the tower height display to account for the remote head. Tower Lens Height +/- units Restore Defaults Resets this menu page to default settings www.Motion-Impossible.com 17 - Operating System AGITO User Manual OS 5.0 Nova...

  • Page 23: Display Settings

    Restore Defaults Resets this menu page to default settings RADIO COMMUNICATIONS (RF) SETTINGS This menu enables the configuration of the AGITO RF modules and other data communications settings ITEM DESCRIPTION (*denotes default setting) This setting enables a mode called Forward Error Correction which can improve signal quality in “congested RF environments”.
  • Page 24 Master Product Code Master Controller Hardware ID Core Serial Number AGITO Core Serial Number Core OS Build AGITO Core current OS build number Core Product Code AGITO Core Hardware ID UPDATE FIRMWARE This menu allows the operator to perform Firmware updates...
  • Page 25 Unlock Duration 3 Hours* 6 Hours 12 Hours Time Remaining Displays the remaining run-time duration Extends the run-time by the default duration without re-entering the PIN Restore Time code AGITO User Manual OS 5.0 Nova 20 - Operating System www.Motion-Impossible.com...

  • Page 26: Sports Mode

    CONNECT / CALIBRATION SCREEN (SPORTS MODE) The purpose of this screen is to ensure that the AGITO system is correctly configured for Sports Mode operation. The system status window (centre of display) will display battery telemetry and confirm serial number of the core you are connecting to. It will also confirm the application mode, i.e.
  • Page 27 Change the function of the Free/Film switch. Free/Film Switch (Sp) Standard* switches between settings memories Steering Lock, see “Steering Hold” on page 42 Steering Calibrate Request a steering calibration. AGITO User Manual OS 5.0 Nova 22 - Operating System www.Motion-Impossible.com...

  • Page 28: Tower Controls

    OFF* stops the steering from switching ends. Maintaining the front end at Swap Ends - Reverse all times. ON enables the steering end of the AGITO to swap depending to the direction of movement Control the steering direction behaviours when the chassis is reversing.
  • Page 29 CONNECT / CALIBRATION SCREEN (TRAX MODE) The purpose of this screen is to ensure that the AGITO system is correctly configured for Trax Mode operation. The system status window (centre of display) will display battery telemetry and confirm serial number of the core you are connecting to. It will also confirm the application mode, i.e.
  • Page 30 OFF* the chassis will continue to function with I/O panel at rear. ON the chassis will behave with the I/O panel as the front. Fully disable MAG-Stop function MAG-Stop Override Disabled* MAG-Stop is active Enabled override is active (use caution) www.Motion-Impossible.com 25 - Operating System AGITO User Manual OS 5.0 Nova...
  • Page 31 This menu allows the operator to adjust controls related to the operation of the Tower when in sports mode ITEM DESCRIPTION (*denotes default setting) Tower Enabled Force the system to enable or disable and attached AGITO Tower Input Expo Adjusts the response curve of the input signal Invert Input...
  • Page 32 When calibrated, and a clip has been created the screen will switch to the application Home Screen. This screen is the normal standby and recording display for the AGITO system, it is divided in to three distinct zones to help the operator quickly navigate information when in use, this screen will also display system warnings as it does in Sports and Trax modes.
  • Page 33 Selected Clip Displays the name of the currently selected clip Drive Mode Displays the Drive-end associated with the currently selected clip Rename Clip Option to rename the current clip AGITO User Manual OS 5.0 Nova 28 - Operating System www.Motion-Impossible.com...
  • Page 34 » SETTING UP AGITO AGITO is supplied with a tool kit which includes all of the necessary tools to perform all of the set-up’s and basic maintenance as outlined in this manual. Should any of these tools need replacing please see our recommendations below: Metric Hex Keys: 2.5mm, 3mm, 4mm, 5mm;...
  • Page 35 Push the battery firmly into the slot. You will hear an audible CLICK from the locking mechanism on the back of the battery when it is in place. ALWAYS RUN AGITO WITH TWO BATTERIES THAT ARE OF EQUAL CHARGE TO ENSURE OPTIMUM RUN-TIMES »...
  • Page 36 Slide the wheel onto the shaft Align the hexagons on the wheel and the shaft and slide in Using the supplied AGITO Wheel Nut Tool to screw on the wheel nut. Make sure it is tight (but take care not to damage the thread or nut) to prevent it coming loose whilst in motion.
  • Page 37 Rotate the rod until the wheels align. Do this to all four wheels, remember to re-tighten the locking nuts. ALWAYS ENSURE WHEELS AND TRACKING RODS ARE PROPERLY AND SECURELY LOCKED AND FIXED TO THE AGITO DRIVE-ENDS. » SPORTS DRIVE-END: ADJUSTING SUSPENSION ��...
  • Page 38 Release the four M screw heads on both Trax Drive-ends, 1 turn Place the AGITO with Trax Drive-ends on to your choice of Track, run the system a short distance to align the wheels with the Track Gauge Tighten the M10 screw head on both Trax Drive-ends, 1 turn or until tight »...
  • Page 39 Y-CORD PEDAL SPLITTER: TOWER ONLY CONTROL (SPORTS) ALWAYS ENSURE MASTER CONTROLLER IS POWERED DOWN WHEN ATTACHING ACCESSORIES. Attach the Y-Cord Pedal splitter box to AUX 2 of the MASTER Controller Plug in the two pedals AGITO User Manual OS 5.0 Nova 34 - Setting up www.Motion-Impossible.com...
  • Page 40 Make sure these are tight and do not come loose ALWAYS ENSURE THE PAYLOAD IS PROPERLY AND SECURELY FIXED TO THE AGITO CORE, USE A MINIMUM OF FOUR FIXTURE POINTS. ALWAYS TRY TO KEEP THE PAYLOAD OVER THE CENTRE OF THE CHASSIS, ESPECIALLY WHEN OPERATING AT HIGH SPEEDS.
  • Page 41 Mount or another set of Risers to the top mounting points with four 3/8th inch bolts ALWAYS ENSURE THE PAYLOAD IS PROPERLY AND SECURELY FIXED TO THE AGITO CORE, USE A MINIMUM OF FOUR FIXTURE POINTS » TOWER: INSERTING GAS-STRUTS Remove AGITO Tower from Case.
  • Page 42 Using the manual adjustment buttons, carefully fully contract the tower, now replace the dust cover. The Tower is now ready to mount to the AGITO. DO NOT RUN THE TOWER WITHOUT A PAYLOAD, AS THIS MAY DAMAGE THE INTERNAL MECHANISM.
  • Page 43 TOWER: ATTACHING CAMERA SYSTEM ALWAYS ENSURE THE PAYLOAD IS PROPERLY AND SECURELY FIXED TO THE AGITO TOWER, USE A MINIMUM OF FOUR FIXTURE POINTS. Remove the Quick Release Plate from the Tower Loosen the 3/8th inch lock and lift out plate...

  • Page 44: Operation And Configuration

    CORE. Once the desired operation mode has been selected on the MASTER Controller, the start-up initialisation sequence will begin. For more details see “AGITO OS Menu Structure” on page 15. The CORE Power button will flash if it is unable to connect.

  • Page 45: Throttle Mode

    Throttle Mode • ‘Forward – Brake – Reverse’: When changing direction, the AGITO must come to a complete stop. The throttle must then be released (left in neutral) briefly and reapplied to change direction. This allows the logic in the control system to differentiate between a brake command and a change of direction.
  • Page 46 This means that the chassis will essentially drive like a regular car and maintains the “front end” Driving the AGITO along a 5-meter line will confirm that the alignment is correct, if the system does not follow the line check the mechanical tracking of the “front end”.
  • Page 47 AGITO run better over bumps, it also reduces steering response, calming the AGITO, and making its movement smoother. The AGITO will transfer more weight, as the front will rise when accelerating and lower under braking. Less kick-up makes the AGITO more responsive, good for smooth hard surfaces and lower intensity turns, due to less weight transfer.
  • Page 48 Make sure the MAG-STOP module is correctly fitted to the Trax Drive-End, we normally place this as shown below at the Front / Left side of the AGITO. Positioned on the far side from the Operator for continuity. Ensure the AGITO is positioned in the CENTRE of the Track.
  • Page 49 Until Dynamic Breaking is introduced this will limit the amount of track available for use at slower speeds. WHEN POSITIONING THE MAG-STOP MAGNETS REMEMBER TO COMPENSATE FOR THE LENGTH OF THE AGITO SYSTEM, I.E. QUOTED STOPPING DISTANCES WILL BE +1M FROM THE NON-MAG-SENSE END OF THE AGITO. »...
  • Page 50 OTHER THAN THE POWER SWITCH, SPECIFICALLY THE THROTTLE INPUT / PEDALS. Setting up the AGITO to best suit your driving style and the requirements of the shot is essential. There are many user configurable software options, that when combined with the hardware set-up will vary the drive dynamics / responsiveness. “Mode Settings (Trax Mode)” on page 25 »...
  • Page 51 REPEATABLE MOVES MODE: TURNING ON Repeatable Moves is a hybrid mode that provides basic record and playback of AGITO movement. It is recommended that initial setup is done within either Sports or Trax mode dependant upon the drive-ends in use. Once configured / calibrated, the user can then access Repeatable Moves.
  • Page 52 RECORDING Once Record has been selected, the AGITO Master Controller will begin recording the clip, the display will display “RECORDING” in the mode status. Pressing the MENU or REAR OPTION Button will stop the recording, and put the system in a “paused” state.

  • Page 53: Playing Back A Clip

    REWINDING A CLIP AFTER PLAYBACK After the clip has been played. The AGITO will need to be reset to its start position. This can be done manually in a Sports Mode clip or by using the Rewind feature in a Trax Mode clip. Once the rewind has been completed the system will return to the Standby state, it can be manually adjusted or playback can be selected.

  • Page 54: Deleting A Clip

    To delete a clip, access the Select a Clip screen, highlight the clip that will be deleted. Use the MENU or REAR OPTION button to enter the Repeatable Moves drop-down menu and select Clear Clip. www.Motion-Impossible.com 49 - Operation AGITO User Manual OS 5.0 Nova...

  • Page 55: Changing Settings

    REQUIRE THE RF MODULES BEING RETURNED TO A SERVICE CENTRE TO BE RESET. To change the settings of the AGITO RF modules, navigate to the Top Level Menu by turning on the MASTER Controller or applying a long press to the MENU button. Scroll down and select SYSTEM MENU, then navigate to the RF COMMS menu, see “” on page 18.
  • Page 56 Generally braking is activated whenever the throttle is applied in the opposite direction to your direction of movement. Alternatively using the DEC rate control dial, you can also adjust the behaviour of how the AGITO drifts to a stop when the throttle is released entirely.
  • Page 57 » OPERATOR MODES AGITO Sports, as standard is provided to all new customers with a firmware limited speed of 1400rpm (15mph, 24km/h), this is the limit for all operators who have completed “Standard Operator Training”. More experienced operators will be able to attend “Advanced Operator Training”...
  • Page 58 AGITO » TOWER: MASTER CONTROLLER ADD-ON » OVERVIEW The AGITO Tower Master Controller Add-on unit is designed to enable wireless control of the Tower, specifically when in Sports Mode, without the need for pedals. » CONNECTION TO MASTER The Add-on unit mounts directly to the rear of the Master Controller.
  • Page 59 » TOWER: STANDALONE OPERATION » TOWER SPREADER BASE We highly recommend the use of our Tower Spreader Base when using the AGITO Tower in a standalone application. The plate includes access to the 12v Power input via 4-pin XLR. »...

  • Page 60: Display And Controls

    AGITO » TOWER: HAND CONTROLLER » OVERVIEW The AGITO Tower Hand Controller is a stand alone unit designed to enable wired control of the Tower without the need of an AGITO Core and Master Controller. » CONNECTION TO TOWER The AGITO Tower Hand Controller plugs directly to the “Tower CTL” connection on the Tower I/O panel. By default the system is supplied with a 12m / 40ft cable.

  • Page 61: Battery Attachment

    OVERVIEW The AGITO Mains Power Supply unit is designed specifically for the AGITO Modular Dolly System. It comes primarily as a 48Vdc power supply, providing two unregulated outputs. The 24Vdc and 12Vdc step-down circuits have a combined sub-limit of 12 Amps peak load when used at 240Vac.

  • Page 62: How To Update Firmware

    �� https://motion-impossible.com/how-to-videos/ To update your AGITO CORE and MASTER Controller you will need to download the latest ‘MI Programmer’ Windows PC application from www.motion-impossible.com/downloads Before you run the MI-Programmer.exe file make sure you have plugged in the USB update cable as that will install all the necessary drivers, the program may not run without this step.

  • Page 63: Maintenance

    SPORTS DRIVE-END: SHOCK SERVICE The AGITO Shocks can become dirty over time, getting sand & grit on the main shaft, damaging the O-Rings causing them to leak. We recommend servicing the shocks regularly and replacing the O-Rings at first sign of any leakage.

  • Page 64: Disassembly And Cleaning

    9. Get a piece of packing foam or something that you can use to hold the shock upright. www.Motion-Impossible.com 59 - Maintinance AGITO User Manual OS 5.0 Nova...
  • Page 65 18. Take the Shock Cap and remove the O-Ring seated inside with a pick or small screwdriver. 19. Give everything a clean with a rag and brake cleaner to remove any oil residue. Make sure to also clean all the small components. AGITO User Manual OS 5.0 Nova 60 - Maintinance www.Motion-Impossible.com...
  • Page 66 7. Place the small black washer on the top and fasten with the nylock nut. 8. Take the shock cap and insert the largest O-Ring. 9. Wrap some PTFE thread/tape onto the top thread of the shock body. www.Motion-Impossible.com 61 - Maintinance AGITO User Manual OS 5.0 Nova...
  • Page 67 8. Then replace the bleed screw and repeat steps 6 & 7. If its not feeling springy and there’s no free movement you can proceed to reassembling the shock. 9. Make sure the shock cap is fully tightened 10. Then replace the two grub screws. AGITO User Manual OS 5.0 Nova 62 - Maintinance www.Motion-Impossible.com...

  • Page 68: Final Reassembly

    Using a clean cloth simply wipe the strut clean, removing any residue Make sure that the seal is also clean and clear of residue If you notice any leaks, please contact the Support Team www.Motion-Impossible.com 63 - Maintinance AGITO User Manual OS 5.0 Nova...

  • Page 69: Specifications

    47.5Kg / 104.7lbs 48.8Kg / 107.5lbs Max Payload (Medium Shocks) 22Kg / 48.5lbs * The operator will need to have completed Advanced Operator Mode training to enable access to this mode AGITO User Manual OS 5.0 Nova 64 - Specifications www.Motion-Impossible.com...
  • Page 70 45 + 45Kg 45 + 22Kg 22 + 22Kg Max Payload (per mount) 99lbs + 99lbs 99lbs + 48.5lbs 48.5 + 48.5lbs * Max Speed figures quoted for Trax Drive-end v1.1 www.Motion-Impossible.com 65 - Specifications AGITO User Manual OS 5.0 Nova...

  • Page 71: Technical Drawings

    » AGITO SPORTS BUMPER MOUNTING DETAIL © MOTION IMPOSSIBLE LTD 2016. ALL COPYRIGHTS AND DESIGN RIGHTS RESERVED. THIS DOCUMENT AND THE INFORMATION HEREIN IS CONFIDENTIAL NO PART OF WHICH MAY BE COPIED OR TRANSMITTED WITHOUT THE PRIOR WRITTEN PERMISSION OF S.A.N.D. LTD. IT IS SUPPLIED WITHOUT LIABILITY FOR OMISSIONS OR ERRORS.
  • Page 72 AGITO » AGITO CORE © MOTION IMPOSSIBLE LTD 2016. ALL COPYRIGHTS AND DESIGN RIGHTS RESERVED. THIS DOCUMENT AND THE INFORMATION HEREIN IS CONFIDENTIAL NO PART OF WHICH MAY BE COPIED OR TRANSMITTED WITHOUT THE PRIOR WRITTEN PERMISSION OF MOTION IMPOSSIBLE LTD.
  • Page 73 V-CON PRO 73.00 6.00 © MOTION IMPOSSIBLE LTD 2016. ALL COPYRIGHTS AND DESIGN RIGHTS RESERVED. THIS DOCUMENT AND THE INFORMATION HEREIN IS CONFIDENTIAL NO PART OF WHICH MAY BE COPIED OR TRANSMITTED WITHOUT THE PRIOR WRITTEN PERMISSION OF MOTION IMPOSSIBLE LTD.
  • Page 74 AGITO » MITCHELL MOUNT / TOWER MOUNT © MOTION IMPOSSIBLE LTD 2016. ALL COPYRIGHTS AND DESIGN RIGHTS RESERVED. THIS DOCUMENT AND THE INFORMATION HEREIN IS CONFIDENTIAL NO PART OF WHICH MAY BE COPIED OR TRANSMITTED WITHOUT THE PRIOR WRITTEN PERMISSION OF S.A.N.D. LTD. IT IS SUPPLIED WITHOUT LIABILITY FOR OMISSIONS OR ERRORS.
  • Page 75 - V-LOCK LOCATION HOLE CHANGE - FRONT CHAMFERS VISUALLY MATCHED IN WITH SUSPENSION ANGLES © MOTION IMPOSSIBLE LTD 2016. ALL COPYRIGHTS AND DESIGN RIGHTS RESERVED. THIS DOCUMENT AND THE INFORMATION HEREIN IS CONFIDENTIAL NO PART OF WHICH MAY BE COPIED OR TRANSMITTED WITHOUT THE PRIOR WRITTEN PERMISSION OF S.A.N.D.
  • Page 76 AGITO » PSU (MAINS POWER SUPPLY) © MOTION IMPOSSIBLE LTD 2016. ALL COPYRIGHTS AND DESIGN RIGHTS RESERVED. THIS DOCUMENT AND THE INFORMATION HEREIN IS CONFIDENTIAL NO PART OF WHICH MAY BE COPIED OR TRANSMITTED WITHOUT THE PRIOR WRITTEN PERMISSION OF S.A.N.D. LTD. IT IS SUPPLIED WITHOUT LIABILITY FOR OMISSIONS OR ERRORS.
  • Page 77 X.XX = X.XXX = ANGLES = THIRD ANGL DIMENSION DRAWN BY DATE SCALE:1:10 SELF LEVELLING FEET POWER INPUT TITLE: STAN DWG NO. SHEET 1 OF » AGITO TOWER STANDALONE HAND CONTROLLER AGITO User Manual OS 5.0 Nova 72 - Specifications www.Motion-Impossible.com...
  • Page 78 GPIO GPIO GPIO +3Vdc (Reserved) I2C_CLK I2C_DAT 10 GND Connector Label Connector P/N Pin Description Mating Connector P/N RS 862-1573 Future Use - not connected USB 2.0 Type B Plug www.Motion-Impossible.com 73 - Specifications AGITO User Manual OS 5.0 Nova...
  • Page 79 Connector Label Connector P/N Pin Description Mating Connector P/N Data LEMO-EGG.0B.304.CLL LEMO-FGG.0B.304.CLAD52 TX RS-232 Data RX RS-232 Data Connector Connector P/N Pin Description Mating Connector P/N Label Power LEMO-EGG.0B.302.CLL LEMO-FGG.0B.302.CLAD52 +12Vdc (1A max) AGITO User Manual OS 5.0 Nova 74 - Specifications www.Motion-Impossible.com...
  • Page 80 Mating Connector P/N Fibre Optic 1 Single Mode Fibre Channel Fibre Optic 2 » TOWER HAND CONTROLLER Connector Connector P/N Pin Description Mating Connector P/N Label FGA.1B.304.CLAD CAN - CAN + +7-37VDC www.Motion-Impossible.com 75 - Specifications AGITO User Manual OS 5.0 Nova...
  • Page 81 Neutrik NAC3FCB Neutrik NAC3MPB-1 (GREY) Live Neutral Power-in (blue) and power-out (grey) versions with different keying to avoid the possibility of inter-mating. �� For assembly instructions please visit: http://www.neutrik.co.uk/media/10217/download/ BDA%20452%20V4%20-%20powerCON%20-%20NAC3FCA%20%2B%20NAC3FCB.pdf?v=5 AGITO User Manual OS 5.0 Nova 76 - Specifications www.Motion-Impossible.com...
  • Page 82 Label 48Vdc ECJ.2B.302.CYC +48Vdc FGJ.2B.302.CYMD72 UNLIKE OTHER CABLES WITHIN THE AGITO SYSTEM PIN 1 IS POSITIVE ALWAYS USE THE CORRECTLY SPECIFIED CABLE, THE OUTPUT OF THIS PSU DELIBERATELY MATCHES THE 2-PIN LEMO USED WITH SHOTOVER SYSTEMS Connector Connector P/N Pin Description...

  • Page 83: Troubleshooting

    (black line is visible). The E-STOP on the MASTER must also be deactivated. (AGITO Trax, via AGITO Hub) Check that the AGITO Hub is plugged in the correct AUX port on the Master (AUX 1) and that the Hb icon is green...
  • Page 84 Check that all E-STOP’s are in the deactivated position. Track Distance feedback is wrong There are two versions of AGITO Trax Drive-ends which have different encoder capabilities. If your readout is more than the distance actually travelled, then you are likely to have a v1.0 generation drive-end but are running the v1.1 conversion.

  • Page 85: Further Support

    Email: US.support@Motion-Impossible.com (Monitored 7 days a week) ABELCINE, New York Industry City 88 35th St, 4th Fl Brooklyn NY 1 1232 ABELCINE, Los Angeles 801 South Main St. Burbank CA 91506 AGITO User Manual OS 5.0 Nova 80 - Support www.Motion-Impossible.com...

This manual is also suitable for:

Agito nova 5.0Agito core v 1.1Agito master v1.0Agito tower v1.0Agito mains psu v2.0

Table of Contents