Cooper HALO ALB2A40GY Instruction Manual

ALB2A40GY
ALB4A40GY
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Adjustable wrench or ratchet wrench with 10mm socket
• Drill with 3/16 in. drill bit
• 1/2 in. diameter conduit (if applicable, length depends on application)
• 1/2 in. watertight conduit connectors (if applicable)
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the follow-
ing:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Edges may cut. Handle with care.
• Connect fixture to a 120 Volt, 60 Hz power source. Any other connection voids the
warranty.
• Fixture should be installed by persons with experience in household wiring or by
a qualified electrician. The electrical system, and the method of electrically con-
necting the fixture to it, must be in accordance with the National Electrical Code
and local building codes.
• Upside down installation can result in overheating or accumulation of water in
fixture. Install right side up.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following
2 conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
Questions? / Des questions? / ¿Preguntas ? 1-800-334-6871 ConsumerProducts@cooperlighting.com
PACKAGING CONTENTS/ CONTENU DE L'EMBALLAGE / CONTENIDO DEL PAQUETE
A. Light fixture
Appareil d'éclairage
Accesorio
D. Pole Mounting Clamp
(2) Pince de montage de poteau
(2) Abrazadera de montaje en
Instruction Manual / Manuel d'instructions/ Instrucciones
B. Access Cover
Support de montage encliquetable
Couvercle d'accès
E. (3) Wire Connectors
(2) Connecteurs de fils
(2) Conectores de alambre
communications. However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void the user's
authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
MOUNTING & WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect power at fuse or circuit breaker before
installing or servicing.
NOTE: This fixture is intended to be conduit connected to a properly installed and prop-
erly grounded metal weatherproof junction box (not included). All conduit connectors,
conduit, and junction boxes (sold separately) should be cULus Listed suitable for wet
locations.
1. Turn off the power at the main fuse/breaker box
2. Using the pattern on the box, mark and drill holes
for mounting.
NOTE: Mount this fixture in an upright and level
position.
3. Install the two bottom mounting screws (C) first,
leaving enough room between the mounting
screws and the mounting surface to accommo-
date mounting the fixture.
4. Screw the top mounting screw (C) into the
predrilled hole and back the screw out. This will
leave the hole threaded and make installation of
the fixture easier.
5. Remove the cover plate by loosening the two mounting screws (F) inside the cover
plate.
6. Remove access cover (B) from fixture (A). Install the first conduit connector and
conduit (sold separately) into the access cover (B) (Fig. 1).
7. Feed supply wires into conduit. Attach ground wire that is attached to fixture housing
(A) to the junction box earth ground wire.
8. Connect the black fixture wire to the black supply wire (hot) with UL-approved wire
connector (E). Connect the white fixture wire to the white supply wire (neutral) with
UL-approved wire connector (E).
NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire
extend from the wire nut or other approved wire connectors (E).
1
C. (3) Mounting Screws
(2) Vis de montage
(2) Tornillos de montaje
F. (2) Access Cover & Pole Mounting Clamp Mounting Screws
(2) Couvercle d'accès et vis de montage du collier de montage
(2) Tornillos de montaje de abrazadera de montaje de
cubierta y poste de acceso
1
CONDUIT
CONDUIT
CONNECTOR
Lighting Solutions