Advertisement
5. OPERATION
5.1.
Coupling
5.1.1. .
Ensure the air valve is in the "off" position before connecting to the air supply.
5.1.2.
An air pressure of no more than 8bar (115psi) and an air volume of 10cfm will be required.
WARNING! Ensure the air supply does not exceed 8bar (115psi). Too high a pressure will shorten the product life and may
‰
be dangerous, causing damage and/or personal injury.
5.1.3.
Drain the air supply tank daily. Water in the air line will damage the gun.
5.1.4.
Clean the air inlet filter screen weekly.
5.1.5.
For recommended hook-up, see fig.1.
5.1.6.
Line pressure should be increased to compensate for unusually long air hoses (over 8 meters). The minimum hose diameter should
be 1/4" internal diameter and fittings must have compatible dimensions.
5.1.7.
Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.
fig.1
WARNING! Ensure you read, understand and apply
‰
the safety instructions in Section 1 and follow the
manufacturer's instructions on the underseal/wax
container.
5.2.
Preparing the gun for use.
5.2.1.
Pour the underseal/wax into the SG16.V4 canister,
screw the canister onto the gun, (fig.2.A).
5.2.2.
Attach nozzle (fig.2.C) to the gun. Ensure that the
nozzle is not screwed too far into the gun as this will affect the efficiency of the delivery. Tighten the nozzle lock nut.
5.2.3.
Ensure the air supply is regulated to no more than 8bar (115psi) and then attach the air hose to the gun.
5.2.4.
Adjust the air control valve to achieve the desired flow of material being applied.
5.2.5.
Aim the nozzle of the gun into a safe area and depress the gun trigger to check for correct operation. It may be necessary to adjust
the position of the nozzle in the gun to achieve the most effective delivery.
5.3.
Using the injection probe
5.3.1.
The SG16.V4 is supplied with an injection probe (fig.2.D) for use with wax. The flexible injection probe enables wax to be sprayed
into cavities, between panels and inside doors etc.
5.3.2.
The injection probe (fig.2.D) is interchangeable with the nozzle (fig.2.C) on the gun. Remove the lock nut from the nozzle and attach
it to the injection probe. Ensure that the injection probe is not screwed too far into the gun as this will affect the efficiency of the
delivery. Tighten the lock nut to hold the injection probe in position and attach the canister (fig.2.A) to the gun.
5.3.3.
Ensure the air supply is regulated to no more than 8bar (115psi) and then attach the air hose to the gun.
5.3.4.
Adjust the air control valve to achieve the desired flow of material being applied.
5.3.5.
Aim the injection probe into a safe area and depress the gun trigger to check for correct operation. It may be necessary to adjust the
position of the injection probe in the gun to achieve the most effective delivery.
6. MAINTENANCE
WARNING! Ensure the gun is disconnected from the air supply before attempting any maintenance. It is very important to keep the
‰
gun and components clean to ensure free passage for the underseal/wax.
6.1.
After use clean all items thoroughly, especially the probe, with a suitable cleaning agent and allow to dry before storage.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
fig.2
Environmental Protection
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
Original Language Version
01284 757500
01284 703534
SG16.V4| Issue 1 15/09/16
www.sealey.co.uk
Web
sales@sealey.co.uk
Advertisement
