Table of Contents
Advertisement
Quick Links
EDS - TECHNICAL INSTRUCTIONS
REFLECTIVE TYPE OPTICAL
BEAM
SMOKE DETECTOR
RK100 - R
RK100 - RS
with Laser Pointer
BLP-100
TECHNICAL MANUAL
TECHNICAL INSTRUCTIONS FOR
INSTALLATION, SETUP AND
MAINTENANCE
1
EDS - V. Ca' Nova Zampieri 6 - 37057 S. G. Lupatoto - VERONA - Tel. +39045547529 - Fax. +390458750065 - eds@eds.eu -www.eds.eu
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for EDS RK90R
Summary of Contents for EDS RK90R
- Page 1 RK100 - R RK100 - RS with Laser Pointer BLP-100 TECHNICAL MANUAL TECHNICAL INSTRUCTIONS FOR INSTALLATION, SETUP AND MAINTENANCE EDS - V. Ca' Nova Zampieri 6 - 37057 S. G. Lupatoto - VERONA - Tel. +39045547529 - Fax. +390458750065 - eds@eds.eu -www.eds.eu...
-
Page 2: Table Of Contents
EDS - TECHNICAL INSTRUCTIONS NOTE - the version RK100-RS is not equipped with the detection circuit of Turbulence. Therefore no items related to this function are included . Keep in mind this indication while reading and using these instructions. CHAPTER INDEX... - Page 3 The procedure below is intended for trained personell with previous experience in installing EDS Beam Smoke Detectors RK100R(S). If you don’t have the needed experience please refer to the standard installation procedure of this manual. On our site www.eds.eu is available a video with instructions for installing the RK100R-S.
-
Page 4: Qualified Personell
• 1 - 7mm “C” Key • 1 - multimeter (we recommend an analog hand Tester or EDS analog STS-01 meter (optional) to be plugged on the special connector positioned on detector’s circuit. 3.2 - Unscrew the 4 fixing screws (fig. 2) and remove the cover 3.3 - Install the detector at a distance from the ceiling within the 10% of the height of the room to protect. -
Page 5: Cable Connections
EDS - TECHNICAL INSTRUCTIONS 3.5 - Install the FX reflector on the opposite wall at the same distance from the ceiling as the detector. It is not necessary that the device is perfectly in front of the optical reflector or perpendicular to it (small angle shift are possible in all directions). -
Page 6: Operation
7.1.1 - The pointer is installed on board of the RK detector in order to speed the optical alignment operation between the detector and the reflector 7.1.2 - The BLP Laser pointer is an accessory that makes the installation faster EDS detectors. It allows a fast primary alignment. But it is always useful to make the electrical alignment (fine adjustment). - Page 7 8.7 - To get the best results in the following operations, we recommend the use a measuring instrument (Multimeter), preferably an analog hand type, for better control of the variations of the signal during the setup. Good results are also obtained using EDS analog meter STS01 (optional), designed for this application, that must be inserted on the special connector CN4, set on the printed circuit of the detector (v.
- Page 8 EDS - TECHNICAL INSTRUCTIONS 8.11 - If the alignment with the Laser pointer was well executed, normally the operation listed below is unnecessary and you can go directly to step 8.13. Search for the maximum output signal optimizing the optical alignment of the Transmitter acting slowly and in sequence on the 3 regulation screws V1-V2-V3 of the optic crew.
-
Page 9: Autocompensation
EDS - TECHNICAL INSTRUCTIONS If this signal adjustment is critical or, if turning the trimmer with small movements, you notice big changes on the signal level, review as described in cap. 8.10. 8.14 - It must be checked out that, since the detector founds its operation on the reflection of the projected beam, this reflection is effected by the FX reflector only and not from other elements. -
Page 10: Fault Output
EDS - TECHNICAL INSTRUCTIONS 11 - FAULT OUTPUT 11.1 - On the terminal block of the detector is available the contact of fault/anomaly relay. This relay is normally excited and will turn not- excited if the followings conditions are verified: •... -
Page 11: Frontal Leds Operation
EDS - TECHNICAL INSTRUCTIONS must be restored and the red Led restarts to flash every 10 seconds. If the function of memorization is activated (cap.14) for the restoration, it is necessary to remove the eletric power from the detector for 5 seconds. -
Page 12: Technical Data
• Model: RK100-R, RK100-RS • Type: Reflective Type Optical Beam Linear Smoke Detector • Manufacture: EDS srl - V. Cà Nova Zampieri 6 - 37057 S.G. Lupatoto - Verona - Italy • Power supply range: 11- 30 Vcc • Optical path lenght: 100m (depends on the type of reflector used - fig.7) •... - Page 13 EDS - TECHNICAL INSTRUCTIONS disco bianco white disc rivelatore riflettore foro hole diodo fotoemittente fig.1 photoemitting diode fig.4 fig.5 fig.2 diametro del raggio [cm] distanza [m] fig.3 fig.6...
- Page 14 EDS - TECHNICAL INSTRUCTIONS ° ° < > fig.7 fig.8 REFLECTOR TABLE...
- Page 15 EDS - TECHNICAL INSTRUCTIONS...
- Page 16 EDS - TECHNICAL INSTRUCTIONS DS1649A LED di Allineamento LED di Allarme Relè Guasto fault Fehlerrelais relay Turbo Relè turbo Turborelais relay TURBO SENS POWER Relè Allarme alarm Alarmrelais relay fig.9...
- Page 17 EDS - TECHNICAL INSTRUCTIONS INTERNAL PARTS P1 - Trimmer for the signal level regulation Normally regulated to 50-60% that corresponds to a signal of 5V at the maximum distance. SW1 - Selector for the regulation of the sensitivity of the circuit sensible to Turbulence (heat). Sensitivity increases from 1 to 4.
- Page 18 EDS - TECHNICAL INSTRUCTIONS DS1650A LED di Allineamento LED di Allarme Relè Guasto fault Fehlerrelais relay Turbo Relè turbo Turborelais relay TURBO SENS POWER Relè Allarme alarm Alarmrelais relay fig.10 INTERNAL PARTS WITH STS-01 METER INSERTED segnale analogico 0-5V analog signal output 0-5V contatto relè...
- Page 19 EDS - TECHNICAL INSTRUCTIONS Example of RK100R connection with a zones Control Unit CENTRALE DI CONTROLLO alimentazione connessione zona1 segnale analogico 0-5V schermo contatto relè GUASTO resistenza di Allarme contatto relè TURBOLENZA contatto relè d'ALLARME resistenza di fine linea alimentazione 11-30 Vcc fig.12...
- Page 20 RK90R/S - RK100R/S - RK100/200B/S SUP - 90 Adjustable bracket for RK90R detector. It allows the installation of the detector in angular positions. It is very useful for installations in museum halls, picture galleries, churches, etc. This bracket allows angle shift of + /- 90° in all the directions.
- Page 21 4 - Name, registered trade name or registered trademark and contact address of the manufacturer as required pursuant to article 11(5) : EDS srl , Via Cà Nova Zampieri 6, San Giovanni Lupatoto (Verona) , 37057, Italy 5 - Where applicable, name and contract address of the authorised representative whose mandate covers the tasks specified in article 12(2) : Not applicable.
- Page 22 EDS - TECHNICAL INSTRUCTIONS 9 - Declared Performance. All requirements including all essential characteristics and the corresponding performances for the intended use or uses indicated in 3 have been determined as described in the hEN mentioned in the following. Essential Characteristics...
- Page 23 The performance of any warranty service under this Agreement is not an admission or EDS S.r.l. - Via Cà Nova Zampieri 6, 37057 S. G. Lupatoto - Verona, Italy (hereinafter “EDS”), guarantees its products to be free from agreement that the design or manufacture of a product is defective.
- Page 24 EDS - TECHNICAL INSTRUCTIONS The information contained in this document have been carefully checked and are reliable. By the way EDS company is not responsable in any way for possible inaccurancies or errors and it reserves the right to perform changes in any part of this document and/or product, to improve the quality, reliability or the design.
Need help?
Do you have a question about the RK90R and is the answer not in the manual?
Questions and answers