Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Orcomm ORC-E3
Summary of Contents for Orcomm ORC-E3
- Page 1 ORC-E3 Version 1.0 - Installation and User Manual...
-
Page 2: Table Of Contents
Please follow this user manual for the correct installation and testing, if there is any doubt please call our tech-support and customer centre. The illustrations shown here are only used for reference, if there is any difference please take the actual product as standard product. - Page 3 LAN setting: ............................12 Access setting: ........................... 14 VOIP: ..............................15 Forward: (Call transfer): ........................16 ExModule: ............................17 Advanced: ............................17 Default: ............................. 18 Logout: .............................. 18 Maintenance of devices ........................19 Please Note ............................19...
-
Page 4: Basic Operation
Basic Operation: When programmed as outdoor panel, input floor and room number (the digit is 3 at least), then press “✓” to confirm. If you forget to press “✓” to confirm the input, it will call after 2 seconds automatically. When the room number is ＜2 digits, you should press ““✓””... -
Page 5: Basic Settings
Basic Settings: Press (“✓”) key twice, the LCD screen will show as following: Enter the system password (Factory default one is 123456) to enter the main menu In Set menu, you can set following items. Application Press “✓” key to enter the following setting screen: Press “2”... -
Page 6: Reg. Card
Reg. card Press “✓” key to enter the following setting screen: When in this mode enter the room number that you want to assign access card to. Touch ID card to the panel reader. Press to confirm. “✓” Unlock Press “✓” key to enter the following setting screen: Input the value (1-9 corresponding 1-9 seconds). -
Page 7: Password
Input the value (0-9 corresponding 0-9 seconds). Then press “✓” key to confirm. it will show you “Success” on the display. For example, if press 5, it indicates that the delay unlocking time is 5 seconds. When the user unlocks the door, it will be unlocked after the 5 second delay has lapsed. Password Press “✓”... -
Page 8: Language
Input digit from 1-4 to select different ring tone. Then press “✓” button to confirm the, it will show you “Success” on the display. Language Press “✓” key to enter the following setting screen: Input digit “1” for simplified Chinese, “2” for English, “3” for Russian, “4” for Traditional Chinese, “5” for Turkish, “6”... -
Page 9: System Setup
System Setup In System Setting menu, you can do the following settings: Device No You can install 99 outdoor panels in one building. If you want to install more than one outdoor panel in one building, you need to set your outdoor panel into two type: main & sub outdoor panel. Press “✓”... -
Page 10: Mask
Press “✓” key to enter the following setting screen: The IP address is unique in the same LAN network. If the total quantity of the IP address in one community or project is ≤255, you only need to revise last 3 digits (0～255); if the total quantity of the IP address is ＞255, you need to revise last 6 digits (0～255;... -
Page 11: Server
The default is 192.168.68.1. The setting of gateway address should be accessible to the IP address given to the device. Just to confirm the Gateway address is also in the same network segment. Server Press “✓” key to enter the following setting screen: Enter the address of management server if one is being used on the system. -
Page 12: System Information
System Information Press “✓” key to enter the following setting screen: Press “2”up or “8” down key to check the relevant information of system. NET: network connectivity status. When the system display “ERR”, the network is disconnected; when it displays “Ok”, the network is connected. SIP: registration status of SIP server. -
Page 13: Lan Setting
Connect outdoor panel and PC in the network switch and make them in the same LAN. Input IP address of outdoor panel in the web browser of PC (For best results please use Internet explorer), then input the user name and password (the default name is admin, the password is 123456) to enter into the following interface: LAN setting: Click “LAN”... - Page 14 Mask: the default Mask is 255.255.255.0. Gateway: it depends on IP address. DNS: it depends on LAN. Server IP: it is the same as the IP address of management PC. NTP: it refers to network time protocol source address. Usually, the communication among management centre, indoor monitor and outdoor panel will be available in the same LAN;...
-
Page 15: Access Setting
Click “Submit” icon to confirm settings. Access setting: Click “Access” icon on the interface to enter into the following interface: Unlock timeout: After 1-9 seconds, the door is closed. Unlock delay: The door lock is unlocked after 0~9 seconds. Elev refer: It is reserved. Security ON/OFF: It is reserved. -
Page 16: Voip
VOIP: Click “VOIP” icon on the interface to enter into the following interface: Input the relevant information if you have a SIP server or network/system engineer. Proxy: Enter the IP address of the SIP register server. Realm: Enter the Realm name or IP address. If unknown use same as proxy server. Outbound: If an outbound SIP server is being used enter the address hear. -
Page 17: Forward: (Call Transfer)
Forward: (Call transfer): Click “Forward” icon on the interface to enter into the following interface: 1. Make the call to another SIP extension (with SIP server) For example, you want to call SIP extension 100, you can set it like this: So, when you press 100 on the outdoor panel, it will call extension 100 via the SIP server. -
Page 18: Exmodule
2. Make the SIP call to another SIP device (Without SIP server, Direct SIP calling) For example, you want to call a SIP device with IP address 192.168.15.100, you can set it like this: SIP:1@192.168.15.100 (Note: “1” has no indication of the number being called. “1” can be any factious number) When you press 100 on the outdoor panel, it will call the SIP device with IP address 192.168.15.100. -
Page 19: Default
Default: Click “Default” icon on the interface to enter into the following interface: Click “Submit” icon, now all the registered cards are deleted (admin card cannot be deleted). To back up all the setting on the outdoor panel; Click “Click to backup settings” icon, the system will back up the current settings. Save the downloaded file for future restores or changes. -
Page 20: Maintenance Of Devices
Maintenance of devices Keep the surface of the screen clean using a soft dry cloth only. • • Do not use benzene, thinner or organic solvents such as gasoline to clean, these solvents may cause damage to product. Please Note •...