Advertisement
Install the Device/ 设备安装
G Connect Cables/ 连接线缆
3
Connect the audio cable.
连接音频线。
4
Connect the alarm cable. It is recommended that twisted pair cables be used as alarm cables. The diameter of
the cable core ranges from 22 AWG to 28 AWG. The impedance of the entire cable is less than or equal to 100
ohms.
连接告警线缆。告警线缆建议使用双绞线，线芯的线径为 22AWG ～ 28AWG，整条线路的阻抗≤ 100Ω。
5
Use the insulation tape to insulate the connection part of each cable. Then use the waterproof tape and
insulation tape to wrap the cables together into a bundle. Wrap a layer of PVC insulation tape and three layers
of waterproof tape. Then wrap three layers of PVC insulation tape. Ensure that the connection parts of the
cables do not overlap with each other; otherwise, the cable bundle may not pass through the holes because it
is too thick.
先用绝缘胶带对每条线缆对接处做好绝缘防护，然后将所有电缆进行整体绝缘防水处理。绝缘防水处理先缠绕一层 PVC
绝缘胶带， 再缠绕三层防水胶带， 然后再缠绕三层 PVC 绝缘胶带。 对单根线缆做整体缠绕处理时， 不同线缆接口处要错开，
避免某处缠绕后过大而影响穿线。
NOTE/ 说明
• Stretch the waterproof tape evenly until the tape turns twice as long as before. Then use the stretched
waterproof tape to wrap the cable bundle from the insulation sheath to the protection leather hose (for
example, the PVC conduit).
均匀拉伸防水胶带，使其长度为原长度的 2 倍后再缠绕。防水胶带务必从线缆束绝缘外皮开始缠绕至防护皮管（如
PVC 管）。
• When wrapping the tape, ensure that the upper layer covers more than 50% of the lower layer. Each layer
of tape must be tightened and compacted firmly.
缠绕绝缘胶带和防水胶带时需保证上一层胶带覆盖下一层的 50% 以上，每一层都要拉紧压实。
Web Operations/Web 操作
1
Open Internet Explorer, enter an IPC IP address,IP address can be set automatically via DHCP, or a static IP
address can be set manually (192.168.0.120 by default) and press Enter.
当通过PC机直连访问IPC时，请保证PC机IP地址和摄像机IP地址在同一网段 。在Internet Explorer地址栏里输入摄像
机的IP地址，IP地址可以手动进行设置（默认为192.168.0.120），按"Enter"键。当网络中有DHCP服务器时,IPC
可以通过DHCP服务器自动获取IP地址。
NOTE/ 说明
• If a Dynamic Host Configuration Protocol (DHCP) server is configured for the current network and
the IPC automatically obtains its IP address from the DHCP server, the system will automatically set
the IP address.
当网络配备DHCP（Dynamic Host Configuration Protocol）服务器时，系统将自动配置IP地址。
• PC minimum configuration:Intel fou-generation Core i7,with a clock speed of 3.3G，Video RAM
1.0GB，Memory 8.0GB DDR3 1600MHz .It is recommended that only one channel of 4K video be
enabled to prevent frame freezing or artifacts due to insufficient PC performance.
PC机最低配置：CPU，Intel第六代酷睿i7处理器，主频3.3G及以上，显存1.0GB及以上，内存8.0GB DDR3
1600MHz及以上，建议请求一路4K视频，以免因PC机性能不足造成卡顿或花屏。
• Supported browsers (on a 32-bit operating system): Internet Explorer 8 and Google Chrome 32 or
their later versions; Mozilla Firefox 35 to Mozilla Firefox 51; Google Chrome 45 or later versions need
to install the Internet Explorer tab plug-in.
支持的浏览器（32位）：Internet Explorer 8、Google Chrome 32及以上版本；Mozilla Firefox 35~51版
本。Google Chrome 45及版本以上需要安装Internet Explorer tab插件。
• To avoid security risks, change the password when logging in to the system as the admin user for the
first time.
首次使用admin用户登录时，请务必修改密码，以免造成安全隐患。
2
Enter the user name and password. The default user name and password are admin and HuaWei123
respectively.
输入用户名和密码。默认用户名为管理员用户"admin"，默认密码为"HuaWei123"。
3
Click Login.
单击"登录"。
Setting IPC Basic Parameters/ 配置摄像机基本参数
1
Log in to the web client as the administrator.
以管理员用户登录 Web 客户端。
2
Choose Preview > Common , you can set ISP , Video and OSD parameters.
选择"预览配置 > 常用参数"，可以配置摄像机基本的图像参数、视频流参数和 OSD 参数。
3
Choose Preview> IP/Time , you can set IP address and time parameters
选择"预览配置 > IP/ 时间"，可以配置摄像机的 IP 地址和时间信息。
For detail about how to set basic parameters, see
详细配置方法请参见《配置指南》。
Setting Basic Network Parameters/ 配置基本网络参数
1
Log in to the web client as the administrator.
以管理员用户登录 Web 客户端。
2
Choose Settings > Network , you can set basic network parameters.
选择"高级配置 > 网络"，可以配置网络的基本参数。
3
Set the network parameters as planned.
根据规划的数据配置基本网络参数。
For detail about how to set basic network parameters, see
基本网络参数的具体配置方式请参见《配置指南》。
Configuration
Guide.
Configuration
Guide.
Advertisement
