Siemens VS Z5 Instruction Manual page 29

!
After continuous use of more than 30 minutes,
completely disconnect the power cord from the
power supply.
=> Risk of overheating and subsequent damage.
8
Figu e Switchi g o a d off
To switch the vacuum cleaner on or off, press the
ON/OFF button.
9
Figu e Co t olli g the suctio level
The required suction level can be set to the level
required by turning the control knob in the direction
of the arrow.
Low power range
For vacuuming delicate materials,
such as upholstery, curtains, etc.
Medium power range
For the daily vacuuming of light dirt deposits.
High power range
For vacuuming durable floor coverings,
hard floors and heavily soiled surfaces.
Vacuumi g
! Please ote:
Floor tools are subject to a certain amount of
wear,depending on the type of hard floor you have
(e.g. rough, rustic tiles). Therefore, you must check
the underside of the floor tool at regular intervals.
Worn undersides of floor tools may have sharp edges
that can damage sensitive hard floors, such as
parquet or linoleum. The manufacturer does not
accept any responsibility for damage caused by worn
floor tools.
10
Figu e
Adjusting the floor tool:
Rugs and carpets
hard floors
11
Figu e
Remove the crevice nozzle or upholstery nozzle from
the accessories compartment in the appliance lid.
12
Figu e Vacuumi g with accesso ies
Attach the nozzles to the suction pipe or handle as
required:
a)Crevice nozzle for vacuuming crevices and corners,
etc.
b)Upholstery nozzle for vacuuming upholstered
furniture, curtains, etc.
c) Hard-floor nozzle*
- with clip-in edge cleaning bristles:
For gentle but effective cleaning of hard floor
coverings (tiles, parquet, etc.)
- without edge cleaning bristles:
For cleaning dirt in gaps and cracks
The edge cleaning bristles can be removed by
pushing the two catches in the direction of the
arrows.
Figu e
After use, place the crevice or upholstery nozzle back
into the accessories compartment in the appliance
lid.
Figu e
You can use the nozzle parking aid on the back of the
appliance if you wish to stop vacuuming for a short
time.
Once you have switched off the appliance, slide the
hook on the floor tool into the recess on the rear of
the appliance.
Figu e
=>
To overcome obstacles, e.g. steps, the appliance can
also be carried by the handle on the appliance body.
=>
Whe you have fi ished vacuumi g
=>
Figu e
Pull out the mains plug.
Briefly pull the power cord and release
(The power cord rewinds automatically).
Figu e
To store or transport the appliance, you can use the
storage aid on the underside of the appliance.
Stand the appliance upright. Slide the catch on the
floor tool into the groove on the underside of the
vacuum cleaner.
Cha gi g the filte
! Please note: Always switch off the appliance before
changing the filter.
Replaci g the bag
18*
Figu e
=>
If the dust bag change indicator lights up red
continuously when the floor tool is lifted from the
=>
floor and the highest power setting has been
selected, the dust bag must be changed, even
though it may not yet be full. Even if the dust bag is
not full, it may still need changing, due to the type of
dust which has been vacuumed.
First check that the nozzle, suction pipe and flexible
hose are not blocked, as this would also lead to the
dust bag change indicator being triggered.
Figu e
Open the lid by moving the locking lever in the
direction of the arrow.
* depending on model
13
14
15
16
17
19
Ope i g the lid
27