Regulatory Marking - stayer CS85 Operating Instructions Manual

Advance or set back the arm such that the disk
accurately attacks the cutting edge of the tooth. Once
adjusted, tighten the screw t finish the adjustment.
4. Adjust the cutting depth stop. Act on button 3 to release
the rod that establishes the stop up to which the cutting
disk may descend. Use the chain to check that the disk
descends sufficiently but without cutting excessively
damaging the link.
4.2 General instructions for use
Starting and stopping the machine
Press button 1 in position "I" to start the machine. Press
button "O" for stopping it. As an additional safety measure,
the machine will not start in case that, when in operation,
electric power supply is cut and then reestablished. In this
case first the stop button "0" and thereafter the start button
"I" must be pushed to start the machine.
Sharpening
Once the equipment has been adjusted in accordance with
the chain to be sharpened (cf. operations for adjustment),
start sharpening all teeth of one side so that you will
be sharpening one tooth but not the next. After having
finished all teeth cut on one side, change the cutting angle
to the symmetric value (+/- 30o – cf. adjustments) and
start sharpening all teeth that cut on the other side.
Before lowering the disk for sharpening the tooth, make
sure that the pawl positions the link of the chain accurately
such that the disk attacks the cutting edge correctly.
In the moment when the disk lowers the lever mechanism,
it presses the rail such that the chain link becomes safely
fastened.
Proceed to sharpening by making the disk descend
several times and delicately onto the link. Do not do it by
one single descent as this might overheat and damage
the temper of the cutting steel making it fragile and thus
spoiling the chain.
5. Maintenance and service instructions
Disk exchange
Disconnect the power plug. Remove the lid that covers
the disk by removing the three screws. Remove the
threaded washer with one hand while immobilizing
the disk with the other one. Remove the old disk and
place the new one making sure that it fits perfectly on
the projection of the spindle. Secure the disk by strongly
tightening the threaded washer with one hand while
immobilizing the disk with your other one. Put the guard
by fixing its three screws. Before starting to sharpen,
check that the disk does not vibrate or oscillate making it
turn without working.
5.1 Maintenance
Clean with a dry cloth and lubricate movable parts with
light oil (3 IN 1, WD-40, etc.). Regarding any activity not
explained here, address our technical service.
ENGLISH
11
5. 2 Repair service
The technical service will advise you in respect of any
questions you may have on repair and maintenance of
your product and on spare parts.
You may also obtain detail drawings and information
in respect of spare parts over the internet under:
info@grupostayer.com
Our team of technical advisors will be pleased to advise
regarding the acquisition, application and adjustment of
the products and accessories.
5.3 Guarantee
Guarantee card
Among the documents forming part of the electric tool you
will find the guarantee card. You must fill in the guarantee
card complete and attach thereto the purchase ticket or
invoice, and hand them over to your retailer in exchange
for the corresponding acknowledgement of receipt.
NOTICE! Should this card be lacking, ask your retailer
for it immediately.
The guarantee is limited solely to manufacturing or
processing failures and ceases when the parts have been
dismounted, manipulated or repaired outside the factory.
5.4 Removal
We recommend that the electric tools, accessories and
packagings be subjected to a recovery process which
respects the environment.
Only for EU countries:
Do not throw away electric tools!
In accordance
2002/96/EC on unserviceable electric and
electronic apparatus, after its transposition into
national law, they must be collected separately
to subject them to ecologic recycling.
The right to amendment is reserved.

6.1 Regulatory Marking

WARNING: The grinding wheel must support a
rotation speed of 50 m/s.
** Short-time operation: Do not make the
apparatus work continuously for more than 15
minutes.
The vibration emission index as stated has been measured
according to a standardized process, and it may be used
to compare electrical tools with each other.
The vibration emission index as stated may also be used
to estimate exposition in advance.
NOTICE: The vibration emission index as
stated may differ from the described on when
that electric tool is effectively used and
depending on how it is being used.
11
with European Directive