Kenwood TK-3207G Service Manual page 7

TK-3207G
9. When the cloning is successful, the Target unit's "Scan"
and "Key lock" functions will return to their default values
(Scan = OFF, Key lock = OFF).
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
the transceiver cannot enter Clone mode.
• The table shown below will cover the frequency tables used
for wireless cloning.
• Clone mode cannot be entered in battery low state.
• A unit cannot be a "Source Unit" if it is unprogrammed. If
[PTT] is pressed, an "error" tone will sound.
• The language used in cloning depends on the "Model type"
setting, not the FPU setting. C type TK-2207G transceiver
and C, C2, C5 and C6 type TK-3207/3207G transceivers
will use Chinese. Other types English.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the data
in the Source unit.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personal.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the source
transceiver and the target transceiver with a dummy load.
• The transmit output power is automatically set to Low
in Clone mode.
Clone Frequency Table
Type C
Operating
Clone Frequency
440~480
Frequency (MHz)
Table
1 440.000
2 442.000
3 446.000
4 448.000
5 450.000
6 452.000
7 454.000
8 456.000
9 458.000
10 460.000
11 462.000
12 464.000
13 466.000
14 468.000
15 470.000
16 472.000
17 474.000
18 476.000
19 478.000
6
20 480.000
REALIGNMENT /
C2 C5 C6
400~430 370~390 350~370
400.000 370.000 350.000
401.000 371.000 351.000
402.000 372.000 352.000
403.000 373.000 353.000
404.000 374.000 354.000
405.000 375.000 355.000
406.000 376.000 356.000
407.000 377.000 357.000
408.000 378.000 358.000
409.000 379.000 359.000
410.000 380.000 360.000
411.000 381.000 361.000
412.000 382.000 362.000
413.000 383.000 363.000
414.000 384.000 364.000
415.000 385.000 365.000
416.000 386.000 366.000
417.000 387.000 367.000
418.000 388.000 368.000
419.000 389.000 369.000
模式组合
9. 当复制成功时，子机的 " 扫描 " 和 " 键锁定 " 功能将回到它们
的初始值 (扫描 =OFF, 键锁定 =OFF)
注意：
• 经销商可以反复上述过程复制数据到 2 个或更多的对讲机。
• 如果对讲机复制模式被设置为"无效" ，则对讲机不能进入
复制模式。
• 下表包含了无线复制用的频率表。
• 当电池处于低电压状态时不能进入复制模式。
• 如果对讲机是非编程的它将不能成为主机。 如果按[PTT]， 将
发出一个 " 错误 " 音。
• 复制时所用的语言是根据 " 样机类别 " 设置，而不是 FPU 设
置， TK-2207G 的 C 类型的对讲机和 TK-3207/3207G 的 C，C2，
C5 和 C6 类型的对讲机用中文，其它类别用英文。
• 对讲机一旦被设置为主机， 数据传送以后， 它就不能成为子
机。这是为了保护主机里的数据。
• 在无线复制的数据传输过程中， 例如在工作台产生的电波或
电磁干扰有可能引起传输失败。
• 复制模式可以仅被批准的服务人员使用。
• 在交付给最终用户之前，复制模式设置必须被设置为"无
效" 。
• 为了复制，将模拟负载代替主对讲机和子对讲机的天线。
• 在复制模式，发射功率自动设定为低。
复制频率表
类型 C
操作频率
(MHz)
440~480
复制频率表
1 440.000
2 442.000
3 446.000
4 448.000
5 450.000
6 452.000
7 454.000
8 456.000
9 458.000
10 460.000
11 462.000
12 464.000
13 466.000
14 468.000
15 470.000
16 472.000
17 474.000
18 476.000
19 478.000
20 480.000
C2 C5 C6
400~430 370~390 350~370
400.000 370.000 350.000
401.000 371.000 351.000
402.000 372.000 352.000
403.000 373.000 353.000
404.000 374.000 354.000
405.000 375.000 355.000
406.000 376.000 356.000
407.000 377.000 357.000
408.000 378.000 358.000
409.000 379.000 359.000
410.000 380.000 360.000
411.000 381.000 361.000
412.000 382.000 362.000
413.000 383.000 363.000
414.000 384.000 364.000
415.000 385.000 365.000
416.000 386.000 366.000
417.000 387.000 367.000
418.000 388.000 368.000
419.000 389.000 369.000