Related Manuals for Happ Happ25
Summary of Contents for Happ Happ25
- Page 1 Four post lift ...
-
Page 2: Table Of Contents
Four post lift Happ25 4 post hoist Contents 1 Safety instruction and attentions ... - Page 3 Anchor bolt selection he HAPP 25 can be moved, this hoist is shipped with anchor bolts to fix the hoist in position. Customers can purchase Loxon bolts from HAPP or other suppliers to present a flat surface to the hoist legs.
-
Page 4: Safety Instruction And Attentions
Four post lift Happ25 4 post hoist 1 Safety instruction and attentions ... -
Page 5: S Afety Caution Signal
Four post lift Happ25 4 post hoist 1.2 ... - Page 6 Four post lift Happ25 4 post hoist Only authorized personnel in lift vicinity ...
-
Page 7: E Xpected Rated Lifted Assignment
Four post lift Happ25 4 post hoist serious personal injury and even death.) ... - Page 8 This hoist is able to be operated in workplaces within Australia and New Zealand AFTER REGISTRATION by HAPP. Operation of a hoist in accordance with WH&S is the responsibility of the ...
-
Page 9: O Perating I Nstructions
To use this hoist in a workplace contact HAPP for the WH&S registration kit, you will need your serial number of the hoist. Only hoist owners that have the official HAPP company signed and sealed ... -
Page 10: Pre O Peration C Hecks
Four post lift Happ25 4 post hoist Pre ... -
Page 11: Operation
V ehicle h oists i nstalled i n s uch e nvironments a re n ot c overed b y H APP w arranty. Only HAPP hoists that are registered with HAPP and Workplace Health and Safety are to be used in ... -
Page 12: Defects --- M Alfunctions
Four post lift Happ25 4 post hoist Defects ... -
Page 13: Lift Parameter Chart
Four post lift Happ25 4 post hoist 3.2 Lift parameter chart ... -
Page 14: B Rief I Nstallation S Teps
4.1 B rief I nstallation S teps The following represents the basic steps for installation of the HAPP 25, these steps may vary depending on your installation environment. We have provided multiple descriptions of installation to ensure you are able to review the steps and learn what is required before attempting the installation. -
Page 15: Unpack A Ll L Oose F Itting I Tems
Four post parking lift ... -
Page 16: Construct A Nd A Ttach E Nd F Rames
100mm angle grinder to avoid contact with the safety release mechanism. There are two forms of safety latch available for the HAPP 25, internal and external latches. The internal latch mechanism is typically used in workshop focused environments, the external in storage focused environments. -
Page 17: Connect T He C Ables
Four post parking lift ... -
Page 18: Install T He P Ump A Ssembly
Four post parking lift ... -
Page 19: Securing W Ith A Nchor B Olts
a 24mm hole. If you have one type of bolt and wish to switch to the other style HAPP will exchange this at the cost of shipping. A lso longer, bolts and 18 / 19 mmm tru bolts are available for exchange ... -
Page 20: Initial T Esting O F T He L Ift
evenly, adjust with the two nuts on each column. If your cable adjustment runs out of thread use spacers to allow for this. Spacers are available from HAPP to assist if this is the case. Do not operate the lift with uneven cable adjustment. ... -
Page 21: Final T Esting O F T He L Ift
Four post parking lift ... -
Page 22: C Heck Points Before Using
Four post parking lift ... -
Page 23: P Acking, Transport And Storage
Four post parking lift ... -
Page 24: T Rouble S Hooting
Four post parking lift ... - Page 25 Four post parking lift ...
- Page 26 Four post parking lift ...
-
Page 27: E Lectrical S Ystem
Four post parking lift ... -
Page 28: Limit S Witch W Iring
Four post parking lift ... -
Page 29: Electrical W Iring - A S3000
Four post parking lift ... -
Page 30: P Ower U Nit - P Ump A Ssembly
Four post parking lift ... -
Page 31: Exploded V Iew O F P Ump A Ssembly
Four post parking lift ... -
Page 32: Column L Ocation
Four post parking lift ... -
Page 33: Column A Ssembly
Four post parking lift ... - Page 34 Four post parking lift ...
- Page 35 Four post parking lift ...
- Page 36 Four post parking lift ...
- Page 37 Confirm fittings are tight prior to operation. Install the rods for the safety release mechanism. The HAPP 25 has extra bracing under the runway which makes this step harder than usual. You will have installed some of rods earlier in readiness for this step.
- Page 38 Four post parking lift ...
- Page 39 Four post parking lift ...
-
Page 40: Final T Esting
Four post parking lift ... -
Page 41: Entrance R Amp I Nstallation
Four post parking lift ... - Page 42 Four post parking lift ...
Need help?
Do you have a question about the Happ25 and is the answer not in the manual?
Questions and answers