Related Manuals for Basalte Auro Cresnet
Summary of Contents for Basalte Auro Cresnet
- Page 1 Auro Cresnet Manual Auro Cresnet Manual basalte bvba hundelgemsesteenweg 1a 9820 merelbeke belgium 1 / 13 v1.0 © 2017 basalte...
-
Page 2: Table Of Contents
Introduction ..........................3 Installation ..........................4 Identifying the parts ......................4 General functions ........................5 Changing the Basalte Auro Cresnet ID ..................6 Programming in SIMPL Windows .................... 7 Adding a Basalte Auro motion sensor ................. 7 Basalte Auro symbol ......................9 Basalte Auro Configuration module .................. -
Page 3: Introduction
Auro Cresnet Manual Introduction Auro is everything a motion sensor should be: small, fast and almost invisible. When mounted in the ceiling, the innovative flat design makes Auro completely blend in. Only requiring an opening of 1.7”, it is very easy to install. -
Page 4: Installation
Auro Cresnet Manual Installation The Basalte Auro motion sensor is intended for ceiling mounting. To install Auro, an opening should be made with a diameter of 43 mm (1.7 in). Connect the Cresnet bus according the Crestron installation guidelines. The minimal depth required for Auro is 39 mm (1.5 in). Additional depth should be reserved to connect the device. -
Page 5: General Functions
The temperature value can be reported cyclically or on a minimal value change, both in degrees Celsius or Fahrenheit. In SIMPL Windows, a ‘Basalte Auro Configuration’ module is used for every Auro motion sensor in the project, to define the functionality of the sensor. -
Page 6: Changing The Basalte Auro Cresnet Id
Basalte Auro again. A new pop-up-window gives an overview of all Cresnet devices in identification mode. A request is then sent on the Cresnet bus to the selected Basalte Auro. The Polling Mode Status says, ‘Start requested, Start in progress’. -
Page 7: Programming In Simpl Windows
Programming in SIMPL Windows Adding a Basalte Auro motion sensor A Basalte Auro motion sensor is added to the Cresnet Bus like any other Cresnet device, using the Configure System window. You can select the Basalte Auro from the ‘Cresnet Control Modules / Cresnet Sensing Modules’... - Page 8 Auro Cresnet Manual 8 / 13 v1.0 © 2017 basalte...
-
Page 9: Basalte Auro Symbol
After adding a Basalte Auro motion sensor to the SIMPL Windows project, the Program System window can be used to start programming the sensor. All Basalte Auro motion sensors will be shown in the processor’s Cresnet Slot (on the Program View pane). - Page 10 Auro Cresnet Manual An overview of all available signals on the Basalte Auro motion sensor symbol: Signal Name and Type Description Digital input: The Auro’s internal Led can be controlled by this digital input. <LED> When the ‘Led Mode’ is set to ‘Follow Motion’, this digital input will be overruled by the motion feedback.
-
Page 11: Basalte Auro Configuration Module
Be sure to include the ‘Basalte Auro Configuration.umc’ file in the same SIMPL Windows project folder. The module should be visible in the Symbol Library Pane. Add as many of these modules to the project as there are Basalte Auro on the Cresnet Bus. 11 / 13 v1.0... - Page 12 Auro Cresnet Manual An overview of all available signals and parameters on the Basalte Auro Configuration symbol: Signal Name and Type Description Digital input: When a High pulse is sent on this input, all configured <Initialize> parameters are sent in 1 configuration string to the corresponding Basalte Auro device.
- Page 13 Auro Cresnet Manual Parameter: Defines how the Basalte Auro’s temperature is updated. <Temperature Sensor> If enabled, the temperature can be sent every 60 seconds, or on a 0.5° Celsius change. (equal to 0.9° Fahrenheit) Available settings: Disabled Cyclic Delta Parameter: Defines in which format the temperature will be reported.