Related Manuals for Basalte BO.sensor
Summary of Contents for Basalte BO.sensor
- Page 1 BO.sensor Manual BO.sensor Manual basalte bvba hundelgemsesteenweg 1a 9820 merelbeke belgium 1 / 39 v.1.7 © 2014 basalte...
-
Page 2: Table Of Contents
Table of Content General ........................3 Introduction ....................... 3 Beo4 – getting started ..................4 Sources ......................5 BO.sensor ......................7 Beo commands ....................8 KNX control object ....................9 KNX transport and preset object ................10 Configuration of parameters ..................11 General ...................... -
Page 3: General
BO.sensor integrates Bang & Olufsen infrared remote controls with KNX systems and allows controlling KNX lights, screens and scenes with the Beo 4 and Beo 6 remotes. The BO.sensor also supports the BeoRemote One if configured to support Beo4 products. -
Page 4: Beo4 - Getting Started
The standby button (●) has a short and long press function. Short press will switch the currently operated source to standby, long press will switch all sources to standby. 4 / 39 v.1.7 © 2014 basalte... -
Page 5: Sources
Presets are used to determine which audio content will be played from the Asano music server. A preset can be a predefined playlist, an internet radio station or a music genre. The BO.sensor supports up to 18 presets (number 0-9; colored buttons short & long press) to be linked with the presets defined in a MMS-link. - Page 6 Two 1-bit motor control objects (57,58) for controlling screens using the UP and DOWN • navigation arrows; Two 1-bit motor control objects (59,60) for controlling screens using the LEFT and RIGHT • navigation arrows. 6 / 39 v.1.7 © 2014 basalte...
-
Page 7: Bo.sensor
(B) of the BO.sensor are screwed in the Beolink connector (D) on the infrared sensor. The BO.sensor includes an IR output (C) that connects to Bang & Olufsen device with an IR input socket. This output allows you to send IR commands, either send by the remote or from KNX by using a 14 byte command object (object 182: BO command in). -
Page 8: Beo Commands
BO.sensor Manual 1.5 Beo commands The Beo remote control generates IR commands that are received by the BO.sensor. The BO.sensor will translate each Beo command into a KNX command. Using the BO.sensor Beolink output, you can control B&O devices from KNX using a 14-byte object. -
Page 9: Knx Control Object
When enabling audio or video function, 1-byte control objects are used for transmitting KNX commands. These objects are TV control, DVD control, RADIO control, CD control,… depending on the sources enabled in ETS. Combined with a Basalte B.link, other A/V devices can be controlled by the Beo 4 or Beo 6 remote control. -
Page 10: Knx Transport And Preset Object
The PRESET object can be used to select a preset from the MMS.link. A preset can be a predefined playlist, an Internet radio station or a music genre. The BO.sensor supports up to 18 presets (number 0-9; colored buttons short & long press) to be linked with the presets defined in a MMS- link. -
Page 11: Configuration Of Parameters
BO.sensor Manual 2. Configuration of parameters This section describes the configuration of the BO.sensor in ETS and the corresponding KNX objects. 2.1 General Parameter Description Use ALL STANDBY object This parameter defines if you want to use the ALL standby object. -
Page 12: Controls
Press the relevant touch button, then press the centre button to select the button you wish • to edit; the buttons currently hidden are shown in grey. Press the centre button again to edit the button. Your changes will automatically be saved • when you leave the menu. 12 / 39 v.1.7 © 2014 basalte... - Page 13 Creates new menu in ETS Functions 11-20, 21-30, 31-40 These are functions for the Beo6 remote only, you can add them in the configuration tool of the Beo6. Creates new menu in ETS 13 / 39 v.1.7 © 2014 basalte...
- Page 14 (TV, DTV, DVD…), a ‘1’ will be sent to the VIDEO standby object (obj. 40). Use TV When enabled, pressing the TV-button on the remote will send the source number below to the VIDEO source number object (obj. 6). 14 / 39 v.1.7 © 2014 basalte...
- Page 15 This parameter enables or disables the use of mute objects. To mute, press both volume up and volume down buttons on the remote simultaneously, press again to unmute VIDEO mute-object (object 36) VIDEO mute feedback object (object 37) 15 / 39 v.1.7 © 2014 basalte...
- Page 16 AUDIO source number object (object 7). Use DOCK When enabled, pressing the DOCK-button on the remote will send the source number below to the AUDIO source number object (object 7). 16 / 39 v.1.7 © 2014 basalte...
- Page 17 This parameter enables or disables the use of mute objects. To mute, press both volume up and volume down buttons on the remote simultaneously, press again to unmute VIDEO mute-object (object 36) VIDEO mute feedback object (object 37) 17 / 39 v.1.7 © 2014 basalte...
- Page 18 Manual 2.2.4 Hardware buttons of IR sensor The configuration on the BO.sensor allows to choose between 2 different usages of the hardware buttons. Use hardware buttons for Beolink output This function allows you to use the hardware buttons to control a B&O audio source using the Beolink output.
- Page 19 When the PLAY button is pressed, following PRESET number will be send on the selected source PRESET object. Settings: 0-24 Timer timeout (min) This parameter defines the duration of the timer function in minutes. Settings: 0-255 19 / 39 v.1.7 © 2014 basalte...
- Page 20 Objects: 61: TIMER value REMARK When operating the buttons on the IR eye, no debug commands will be sent via the debug objects. These are only intended for the infrared remote controls. 20 / 39 v.1.7 © 2014 basalte...
- Page 21 This parameter enables or disables the control of light scenes by using the coloured buttons and the GO/SELECT button. Configuration of the scenes can be done using the submenu’s in ETS. Communication objects: 55: LIGHT scene 21 / 39 v.1.7 © 2014 basalte...
- Page 22 2. Corresponding submenus allows you to configure the motor control. Communication objects 57: LIGHT UP/DOWN motor open/close 58: LIGHT UP/DOWN motor stop 59: LIGHT LEFT/RIGHT motor open/close 60: LIGHT LEFT/RIGHT motor stop 22 / 39 v.1.7 © 2014 basalte...
- Page 23 This parameter enable or disable the scene save function. If enabled, the scene will be saved by a long touch on the corresponding button Remark : long press is not available for the GO/SELECT button. 23 / 39 v.1.7 © 2014 basalte...
- Page 24 Pressing again while the motor is running will stop the motor. Settings: 0-255 sec Communication objects 57: LIGHT UP/DOWN motor open/close 58: LIGHT UP/DOWN motor stop 59: LIGHT LEFT/RIGHT motor open/close 60: LIGHT LEFT/RIGHT motor stop 24 / 39 v.1.7 © 2014 basalte...
- Page 25 When the remote is in LIGHT mode, you can see the functions above when stepping through LIST. When you selected your scene, just push the GO/SELECT button and the value left from this in the list will appear on object LIGHT function 1-10 value (object 56). 25 / 39 v.1.7 © 2014 basalte...
- Page 26 Sends a value between 0-250 over a 1-byte object. Use as motor Choose between the options: send open, send close, single press toggle Each function will has its own objects and functions completely independent. 26 / 39 v.1.7 © 2014 basalte...
-
Page 27: Version
In this case: v1.1 ETS application build This is the build number of the application In this case: 140801 Product code The product code for the BO.sensor In this case: 770-01 http://www.basalte.be The website from basalte 27 / 39 v.1.7... -
Page 28: Appendix
VIDEO, LIGHT, AUDIO, VMEM, CONTROL Digit 2 VIDEO, LIGHT, AUDIO, VMEM, CONTROL Digit 3 VIDEO, LIGHT, AUDIO, VMEM, CONTROL Digit 4 VIDEO, LIGHT, AUDIO, VMEM, CONTROL Digit 5 VIDEO, LIGHT, AUDIO, VMEM, CONTROL 28 / 39 v.1.7 © 2014 basalte... - Page 29 VIDEO, LIGHT, AUDIO, VMEM, CONTROL STANDBY VIDEO, AUDIO, ALL BACK VIDEO, LIGHT, AUDIO, VMEM, CONTROL VIDEO, LIGHT, AUDIO, VMEM, CONTROL SELECT VIDEO, LIGHT, AUDIO, VMEM, CONTROL CURSOR UP CONTROL CURSOR DOWN CONTROL CURSOR LEFT CONTROL 29 / 39 v.1.7 © 2014 basalte...
- Page 30 FUNCTION 25 LIGHT FUNCTION 26 LIGHT FUNCTION 27 LIGHT FUNCTION 28 LIGHT FUNCTION 29 LIGHT FUNCTION 30 LIGHT FUNCTION 31 LIGHT FUNCTION 32 LIGHT FUNCTION 33 LIGHT FUNCTION 34 LIGHT FUNCTION 35 LIGHT 30 / 39 v.1.7 © 2014 basalte...
- Page 31 BO.sensor Manual FUNCTION 36 LIGHT FUNCTION 37 LIGHT FUNCTION 38 LIGHT FUNCTION 39 LIGHT 31 / 39 v.1.7 © 2014 basalte...
-
Page 32: List Of Knx Communication Objects
1 byte control value 1 byte Counter pulses (0- 255) AMEM control 1 byte control value 1 byte Counter pulses (0- 255) CD control 1 byte control value 1 byte Counter pulses (0- 32 / 39 v.1.7 © 2014 basalte... - Page 33 AUDIO mute toggle mute 1 bit enable AUDIO mute feedback mute feedback from 1 bit enable C-W-T sound system VIDEO standby send 0 (or send 1 1 bit enable and 0) 33 / 39 v.1.7 © 2014 basalte...
- Page 34 Function 11 MOTOR controlled with 1 bit open/close up/down special functions Function 11 MOTOR controlled with 1 bit start/stop stop special functions Function 12 toggle controlled with in/out 1 bit switch C-W-T special functions 34 / 39 v.1.7 © 2014 basalte...
- Page 35 1 bit switch C-W-T special functions Function 18 value controlled with 1 byte Counter special functions pulses (0- 255) Function 18 MOTOR controlled with 1 bit open/close up/down special functions 35 / 39 v.1.7 © 2014 basalte...
- Page 36 Function 24 MOTOR controlled with 1 bit open/close up/down special functions Function 24 MOTOR controlled with 1 bit start/stop stop special functions Function 25 toggle controlled with in/out 1 bit switch C-W-T special functions 36 / 39 v.1.7 © 2014 basalte...
- Page 37 1 bit switch C-W-T special functions Function 31 value controlled with 1 byte Counter special functions pulses (0- 255) Function 31 MOTOR controlled with 1 bit open/close up/down special functions 37 / 39 v.1.7 © 2014 basalte...
- Page 38 Function 37 MOTOR controlled with 1 bit open/close up/down special functions Function 37 MOTOR controlled with 1 bit start/stop stop special functions Function 38 toggle controlled with in/out 1 bit switch C-W-T special functions 38 / 39 v.1.7 © 2014 basalte...
- Page 39 1 bit open/close up/down special functions Function 40 MOTOR controlled with 1 bit start/stop stop special functions BO command in data in ASCII Character C-W-T (format, address, byte string command) string (ASCII) 39 / 39 v.1.7 © 2014 basalte...