Download Print this page

Daytona 89371 Instruction Manual

Slim-mount usb

Advertisement

Quick Links

SLIM-MOUNT USB
PRODUCT FEATURES
● Dedicated 12 V DC automotive device.
● The thin body of this USB power supply provides a sleek fit to the vehicle.
● The single-port USB power supply has an output of 5 V, 2.4 A × 1.
The dual-port unit has an output of 5 V, 2.4 A × 2.
● Easily connect the wiring with the included brake switch branching wire harness.
(※ Except for some switches)
● The clamp is compatible with handlebar diameters of 22.2 mm / 25.4 mm.
● Safe design with 3A fuse.
● Overcurrent protection feature.
● Reversed-connection prevention feature. (fuse blows and input current is cut)
COMPONENTS
No.
Part name
USB power supply body
Underbracket ※Installed
Transformer ※ Installed
Screw ※ Installed
Rubber band (t=2.0, 1 spare)
※1. Compatible wires: 18–14 AWG, 0.75–2 sq ※sq = (JIS) Cross-sectional area (mm2)
④Screw (
②Underbracket (
①USB power supply body
⑤Rubber spacer
INSTALLATION
【 Precautions 】
● For details on removing and installing vehicle parts, etc., refer to the service manual published by the vehicle manufacturer.
● Secure the vehicle on a stable location so that it will not fall over while being worked on,
and ensure the safety of your environment while working.
● Before starting work, refer to the following diagram and check the operation of this product.
● Disconnect the cable from the negative battery terminal on the vehicle.
[ Pre-installation check ]
● Connect +(Red) wire to the positive post of the battery and –(Black) wire to the negative post.
Then check that this product operates correctly.
※ Be careful, the reversed-connection prevention feature will cause the fuse to blow.
Size
Qty
No.
(mm)
1
Extension wire harness
1
Brake switch branching wire harness
1
Wire connector (※1)
1
Cable tie
14×70
2
Glass tube fuse (※2) ※ Installed
Installed)
③Transformer
Installed)
⑥Extension wire harness
⑦Brake switch branching wire harness
#89371 (98437) 1PORT 2.4A (ACC)
#89372 (98438) 2PORT 4.8A (ACC)
Size
Part name
(mm)
1200
270
150mm
3A
⑩ Glass tube fuse (3A/ Installed)
+ (Red)
- (Black)
⑧Wire connector
http://www.daytona-europe.com
[Dimensions]
Qty
1
1
1
2
1
⑨Cable tie (2pcs)
1/4

Advertisement

loading

Summary of Contents for Daytona 89371

  • Page 1 #89371 (98437) 1PORT 2.4A (ACC) SLIM-MOUNT USB #89372 (98438) 2PORT 4.8A (ACC) PRODUCT FEATURES ● Dedicated 12 V DC automotive device. [Dimensions] ● The thin body of this USB power supply provides a sleek fit to the vehicle. ● The single-port USB power supply has an output of 5 V, 2.4 A × 1.
  • Page 2 【 Checking the installation location 】 [Sample installation: Between clutch master cylinder and handlebar switches] 01. The thickness of the USB power supply body Adjust the positions of is 14 mm. Provide a mounting space of the clutch master cylinder, approximately 15 mm on a straight part of ※...
  • Page 3 [Branching the brake switch power supply] [NG] ※ Cannot be used if the connection is made with a coupler. Go to step 17 Wire that carries 12 V when the ignition switch is turned ON. ※ Incorrect installation will cause symptoms such as power being supplied only when the lever is squeezed.
  • Page 4 21. Connect the cable to the negative battery terminal. Use a tester to identify the location where the – battery cable (ground) is connected to the vehicle with an M6 or smaller bolt. After identifying the ground, disconnect the cable from the negative battery terminal.

This manual is also suitable for:

893729843798438