Table of Contents
Advertisement
Quick Links
Operator's manual for Attachment
Operator's
Operator's
Operator's
1280 mm Rear mount Sand spreader for 300-700-series loaders: A21242
Please read this manual carefully before using the equipment, and follow all
instructions.
Keep this manual for later reference.
Avant Tecno Oy 2013 Copyright all rights reserved
manual for Attachment
manual for Attachment
manual for Attachment
S
a
n
d
S
p
r
e
S
a
n
d
S
p
r
e
R
E
A
R
M
O
U
N
T
R
E
A
R
M
O
U
N
T
Sand spreader, rear mount 2013 1
a
d
e
r
a
d
e
r
Advertisement
Table of Contents
Related Manuals for AVANT A21242
Summary of Contents for AVANT A21242
- Page 1 Operator’s manual for Attachment manual for Attachment manual for Attachment 1280 mm Rear mount Sand spreader for 300-700-series loaders: A21242 Please read this manual carefully before using the equipment, and follow all instructions. Keep this manual for later reference. Avant Tecno Oy 2013 Copyright all rights reserved...
- Page 2 Sand spreader, rear mount 2013 1 Dimensions, Sand spreader A21242: Avant Tecno Oy 2013 Copyright all rights reserved...
-
Page 3: Table Of Contents
6.3. Adjusting the spreader......................... 6.4. Clogging of spreader ........................Maintenance and service.....................17 7.1. Checking hydraulic components ....................7.2. Cleaning and lubrication ......................7.3. Drive chain ..........................Warranty terms........................19 Appendix: EC Declaration of Conformity Avant Tecno Oy 2013 Copyright all rights reserved... -
Page 4: Foreword
4(12) 1. Foreword Avant Tecno Oy would like to thank you for your purchase of this AVANT attachment. It has been designed and manufactured on the basis of years of experience and product development. By familiarising yourself with this manual and following the instructions, you ascertain your safety and ensure the reliable operation and long service life of the equipment. -
Page 5: Designed Purpose Of Use
This AVANT Sand/salt spreader is an attachment that has been designed and manufactured to be used with AVANT multi purpose loaders. The spreader is designed to be mounted on the back of the loader models as listed in Table 1, but can be also used normally when mounted to the quick attach system on the loader boom. -
Page 6: Safety Instructions For Using The Sand Spreader
6(12) 3. Safety instructions for using the sand spreader Please bear in mind that safety is the result of several factors. The loader-attachment combination is highly powerful, and improper or careless use may cause serious personal injury or property damage. Due to this, you should carefully familiarise yourself with the manuals of both the loader and the attachment before starting operation. - Page 7 7(12) • Pay attention to the surroundings and any other persons and machines moving in the vicinity. Pay attention to the contours of the terrain as well as other hazards, such as slippery surfaces, loose rocks, or branches and trees that could reach the driver's area.
- Page 8 8(12) Remember to wear proper protective clothing: • The noise level at the driver's seat may exceed 85 dB(A) depending on use and operating conditions. Wear hearing protection while working with the loader. • Wear safety boots while working with the loader. •...
-
Page 9: Technical Specifications
40 l/min, Maximum input of hydraulic energy: 22,5 MPa (225 bar) Air pressure in support wheels: 2,0-2,5 bar Suitable AVANT loader models: See Table 1 Dimensions: Page 2 4.1. Safety labels and main components of the Sand Spreader Listed below are the labels and markings, which must be visible on the equipment. Replace the warning labels, if they have become unclear or if they have detached completely. - Page 10 10(12) Table 3 – Decal warning messages and locations Decal Explanation A46771 Read instructions before use. A46772 Do not go under a raised attachment or loader boom; stay away from raised equipment. A46801 Entanglement hazard, keep clear of rotating parts. Stop the attachment before leaving the driver’s seat.
-
Page 11: Assembly Of The Sand Spreader
11(12) 5. Assembly of the sand spreader The sand spreader is ready for use as delivered. Attach the attachment and its hydraulic hoses to the loader as instructed below. If using the spreader as mounted to the back of the loader, refer to instructions about using the rear lift device and rear auxiliary hydraulics outlet from the operator’s manual of the loader. -
Page 12: Mounting Spreader To Rear Lift Device Or Rear Mount Bracket
A414508 the spreader can be easily mounted to the loader boom allowing temporary use. If you wish to change the type of the couplings, contact your Avant dealer or service point for instructions or installation service. - Page 13 13(12) Conventional quick couplings: Before connecting or disconnecting the standard quick couplings, the residual pressure must be released as shown below. The conventional quick couplings will not connect, if there is pressure in the hydraulic system. To connect or to disconnect the standard quick couplings, move the collar at the end of the female fitting. The hoses should be connected so that the fitting equipped with a coloured cap is connected to the corresponding fitting of the loader.
-
Page 14: Uncoupling And Storage Of The Sand Spreader
14(12) 5.4. Uncoupling and storage of the sand spreader Uncouple and store the spreader on level surface, so that it will stand firmly on its two outriggers and support wheels. Lower the attachment so that the support wheels touch the ground lightly, and drive the loader to turn the support wheels on the side of the quick coupling plate (or turn wheels manually). -
Page 15: Instructions For Use
15(12) 6. Instructions for use Check the attachment and the operating area once more before starting work. Quick inspection of the equipment before starting to use it is part of ensuring safety and the best performance of the equipment. Practise the use of the spreader at an open and safe area. If you are unfamiliar with the loader model in use, it is recommended to practice its use without any attachments. -
Page 16: Operating The Spreader
16(12) 6.2. Operating the spreader Filling the spreader: Fill the spreader only when it is firmly attached to the loader. Lower the spreader on the ground and observe that the spreader and loader might tilt when adding load to spreader. Avoid staying directly in front of the spreader. -
Page 17: Clogging Of Spreader
Repair all leaks immediately after detecting them; a small leak can quickly grow into a big one. Operate the attachment only with type of hydraulic oil that is accepted for use in Avant loaders. Never handle hydraulic components when the... -
Page 18: Cleaning And Lubrication
Finding any of these faults means that the hydraulic hose or component must be replaced. Spare parts are available from your nearest AVANT retailer or authorized service point. Leave the repair work to professional service technicians, if you don’t have adequate knowledge and experience about hydraulic assemblies and how to perform the repairing safely. -
Page 19: Warranty Terms
19(12) 8. Warranty terms Avant Tecno Oy grants a warranty of one year (12 months) from the date of purchase for the attachment it manufactures. The warranty covers repair costs as follows: • Work costs are covered, if the repair is not performed at the factory. - Page 20 SFS-EN ISO 12100, SFS-EN ISO 4413, SFS-EN 13021 Kuvaus: Avant-kuormainten kanssa käytettävä hiekoitin Beskrivning: Sandspridare; arbetsredskap för Avant lastare Description: Sand spreader; attachment for Avant loaders Beschreibung: Sandstreuer; Anbaugerät für Avant Radlader Mallit / Modeller / Models / Modellen: Avant 300-700-series...
- Page 21 Sand spreader, rear mount 2013 1 Avant Tecno Oy 2013 Copyright all rights reserved...
Need help?
Do you have a question about the A21242 and is the answer not in the manual?
Questions and answers