Advertisement

SELWOOD SELTORQUE S100
ELECTRIC SUPERSILENT
7.5KW STATIC – 1097206000
7.5KW S/SILENT – 1016133S40
The products of Selwood Limited, are designed,
developed and produced in the company's Chandler's
Ford factory.
Many features are covered by world-
wide patents. Product names such as Spate, Simplite
and Seltorque, are registered trade marks.
As all products are subject to continuous development,
the
company
reserves
specifications and information given in this manual
without prior notice.
Whilst every care has been taken in the preparation of
this publication the information it contains must not be
regarded as binding.
Amendments to this publication will only be issued to
cover those design changes which fundamentally alter
the build or operation and servicing procedures. They
will be distributed through the company's dealers and
agencies.
Your attention is drawn to the following symbols used
throughout this manual:-
CAUTION
This caution symbol draws attention to special
instructions or procedures that, if not correctly
followed, may result in damage to, or destruction of
equipment.
WARNING
This warning symbol draws attention to special
instructions or procedures that, if not strictly
observed, may result in personal injury.
WARNING
A WARNING SYMBOL WITH THIS TYPE OF
TEXT DRAWS ATTENTION TO SPECIAL
INSTRUCTIONS OR PROCEDURES WHICH, IF NOT
STRICTLY OBSERVED MAY RESULT IN SEVERE
PERSONAL INJURY, OR LOSS OF LIFE.
Additional copies of this manual are available
from Selwood Pt No 1016133S40MAN
Published by Selwood Limited
© Selwood Limited June 2016
Selwood Seltorque S100 Manual
the
right
to
alter
the
Instructions for Ordering
Replacement Parts
1.
Always quote the pump serial number located on
the plate fastened to the bearing and air pump
mechanism housing.
2.
Always quote the part number(s) (ten digit) of the
component(s), NOT the item number(s).
3.
Always quote the description of the component(s).
Items usually supplied together as sub-assemblies will
have the sub-assembly part number printed at the
bottom of the relevant page.
HEALTH AND SAFETY AT WORK
As manufacturers of pumps and associated equipment
we wish to inform you that, in compliance with Section
6 of the Act, safety precautions should be taken with
our products.
We take every care to ensure as is reasonably
practicable that our products are safe and without risk
to health when
properly used.
appropriate health and safety precautions must be
taken, and in particular you are requested to have
special
regard
to
the
requirements leaflet P769 which accompanies each
pump on despatch from our premises.
Our products also conform to the E.E.C. Machinery
Safety Directive and carry the C.E. mark.
Pumps and engines may be fitted with
seals or 'O' rings manufactured from
VITON or similar material.
When
(720° F) a corrosive acid is produced,
which cannot be removed from the skin.
If signs of material decomposition are
evident, or if in doubt, always wear
disposable heavy-duty gloves.
1
Nevertheless,
operational
and
safety
WARNING
temperatures
reach
400° C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Seltorque S100 and is the answer not in the manual?

Questions and answers

Summary of Contents for SELWOOD Seltorque S100

  • Page 1 7.5KW S/SILENT – 1016133S40 Always quote the part number(s) (ten digit) of the component(s), NOT the item number(s). The products of Selwood Limited, are designed, developed and produced in the company's Chandler's Always quote the description of the component(s). Ford factory.
  • Page 2: Safety Precautions

    If in doubt, consult cycles, should be drained off through the drain tap Selwood Pumps or a local lifting expert. provided. Whilst lifting the unit keep personnel well away and never allow people underneath.
  • Page 3: Table Of Contents

    Operation ............4 Maintenance ............4 Electric Motors ............ 4 Fitting Instructions for Fenner Couplings (Electric Motors)..........4 SELTORQUE S100 STANDARD DATA .... 5 ROUTINE MAINTENANCE ........ 5 LUBRICATION AND FASTENING TORQUES .. 6 Pump Lubrication ..........6 Commissioning Period ..........6 After Commissioning Period ........
  • Page 4: General Information

    Selwood Seltorque S100 Manual 1 GENERAL INFORMATION 1.4 Electric Motors All electrical connections should be made through 1.1 Installation adequately rated conductors starters. Isolators and other associated switchgear should The pump unit and its associated baseplate or be of adequate capacity for the imposed power trolley mounting should be positioned on a firm loadings.
  • Page 5: Seltorque S100 Standard Data

    The Company 70ft will be pleased to give advice in this connection. Self Priming Lift 8.8m H Please contact Selwood Pumps in the event of 29ft H experiencing difficulty when servicing. Solids Size 75mm company will also be very pleased to give advice in connection with the machine's installation, operation and maintenance.
  • Page 6: Lubrication And Fastening Torques

    Flushing Chamber T750 – 15W/40 For a period of twelve months from delivery of any Actuator Bore Rubens Selwood pump to the first user thereof, or eighteen Impeller Bore Rubens months from the despatch of any such pump by Paper Gaskets...
  • Page 7: Major Servicing

    Selwood Seltorque S100 Manual To replace outer pump body assembly, fit and 5 MAJOR SERVICING evenly tighten screws (A14), washers (A13), spring washers (A12) and nuts (A11), by sequentially turning each screw a small amount 5.1 Air Pump until they are all fully tensioned. It is important...
  • Page 8: Drive Rod Seal (A25 & A28)

    Selwood Seltorque S100 Manual 10. Seat outside section of actuator seal in inner components can be renewed in accordance pump body recess by gently tapping with a non- with the following instructions. metallic mallet. To replace drive rod bearing (A28) carefully 11.
  • Page 9 Selwood Seltorque S100 Manual valve/upper diffuser assembly, (B01) to (B21) when operating rod (B13) is square to the plate inclusively. Examine condition of float (B11) and and fully lifted. replace with new component if punctured or Check condition of bush (B07) in upper diffuser significantly worn.
  • Page 10 Selwood Seltorque S100 Manual 5.2.2 Peel Valve (B21) fit that will not allow any perceptible rotation of the Instructions 3 to 11. impeller on the shaft, and yet allow the impeller to Remove all deposited solids that would interfere slide into place by hand. Apply Rustilo 431 grease...
  • Page 11: Delivery Valve, (C27)

    Selwood Seltorque S100 Manual (C07) will be withdrawn with the sleeve remove it 11. Push mechanical seal spring onto location and check condition. Replace ‘O’ ring if unsuitable diameter provided on seal head. Ensure that the for further service. spring's coils are correctly supported by the flange of sleeve (C06) and will not become trapped Using seat removal tool (Part No.
  • Page 12 Selwood Seltorque S100 Manual Remove separator assembly and suction tube 13. Using lifting equipment in compliance with the (B27) or (B35) in accordance with Section 0 Health and Safety at Work Act, 1975, position Impeller (C04) pump unit on chassis.
  • Page 13: Bearings And Lip Seal (D15,D18,D04)

    Selwood Seltorque S100 Manual Release nut (D38) and withdraw screw (D27), Gasket (A27) must be renewed, always use a allowing fulcrum pin (D28) to be removed. Drive component supplied by Selwood Pumps. rod (D37) and connecting rod (D26) may then be Ensure that ports in housing (A24) are in the 3 withdrawn.
  • Page 14: Workshop Tools

    Always clean, oil and safely store tools after use. to the outer rings. Complete sets of tools are available by quoting:Part iii) The bearings are square to the shaft No. 0010948200 - Seltorque S100 (Excludes Impeller throughout the fitting procedure. Removal Tool Part No. 0015WRS781) Comprising:- When fitted,...
  • Page 15: Fitting Of Actuator Neck Seal

    Selwood Seltorque S100 Manual 6.2 Fitting of Actuator Neck Seal Lightly clamp seal installation tool against end of drive rod by means of capscrew, as shown. Push seal into rear of inner pump body recess Part No. 0015014000. 3. Clean exposed shaft and tool surfaces, and smear with soft soap.
  • Page 16: Fit Seal Housing Sub-Assembly To Pump

    Selwood Seltorque S100 Manual 6.5 Fit Seal Housing Sub- Assembly to Pump Thoroughly clean exposed drive rod surfaces and position installation tool as shown. Smear tool and drive rod surfaces with oil. Thoroughly lubricate drive rod bearing and drive rod seal with oil and fit new gasket before pushing...
  • Page 17: Assemble Flushing Chamber

    Selwood Seltorque S100 Manual 6.10.Remove Impeller 6.8.Assemble Flushing Pump should be removed from the chassis or the Chamber engine decoupled and the bearing housing supported. Check that circlip has been fitted to eccentric, and Remove suction tube together with separator...
  • Page 18: Fit Replacement Drive End Bearing

    Selwood Seltorque S100 Manual Ensuring that the bearing is square to the shaft and that assembly tool is concentric to the shaft 6.11.Fit Replacement Drive centre line, push bearing onto shaft by applying End Bearing steady and continuous screwing torque to the M16 nut and washer.
  • Page 19: Assembly Of Drive Shaft With Bearings Into Housing

    Selwood Seltorque S100 Manual 6.13.Assembly of Drive Shaft with Bearings into Housing Remove assembly by releasing the 4 x M10 fixings. The bearing carrier can be jacked free by the two screwed holes adjacent to the fixings. Remove the lip seal carrier, ensuring seal is not...
  • Page 20: Fault Finding Guide

    7.FAULT FINDING GUIDE This table gives the most common symptoms arising in connection with water-handling duties. Please consult Selwood Pumps for further advice if the service fault is not described, and particularly if the duty has uncommon characteristics. At no time should the pump be run if its bearing housing or flushing chamber contains contaminated oil. Very small volumes of oil may be lost from these chambers during a day's normal running, but remedial action should immediately be taken if the loss becomes excessive.
  • Page 21 Selwood Seltorque S100 Manual LIQUID IS BEING PUMPED OUT OF AIR PUMP, I.E. WATER CARRY-OVER IS OCCURRING ACTION COMMENT Cheek condition of separator assembly. No significant amounts of water should normally pass across the air pump. The rubber peel valve may not be seating correctly, the float may be punctured, or not be able to rise and fall freely, etc.
  • Page 22 Check that air pump mechanism is not faulty. Excessively worn connecting rod bearings, or an under-sized eccentric or fulcrum pin, could cause this problem. Refer to Major Servicing: 0 Refer to Selwood Pumps if the above advice does not solve your problem.
  • Page 23 Selwood Seltorque S100 Manual This page intentionally blank...
  • Page 24 Selwood Seltorque S100 Manual NOTES: Complete assembly available as Part No. 0010905000 Linear Bearing and Seal Assembly. Part Nos. 0015195000, 9140035070 and 9171044100 available as sub-assembly Part No. 9133035380. Ensure that seal components are positioned as shown above, and are retained by the internal circlip. Great care must be exercised when fitting the circlip to ensure that the lip of the wiper seal is not damaged by the hand tools used.
  • Page 25: Parts List

    Selwood Seltorque S100 Manual 7 PARTS LIST 7.1 Air Pump Parts ITEM DESCRIPTION PART NUMBER Air Hose 9542000000 Hose Clip 9505007004 Suction Valve Box 0015017000 Exhaust Valve Cover 1592306000 Full Nut M8 9025080004 Spring Washer M8 9030080229 Suction and Delivery Valve...
  • Page 26 Selwood Seltorque S100 Manual...
  • Page 27: Separator Parts

    Selwood Seltorque S100 Manual 7.2 Separator Parts ITEM DESCRIPTION PART NUMBER Full Nut M10 9025100004 Spring Washer M10 9030100229 Separator Cap 0015034000 Separator Cap Gasket 0015043000 Port Plate 0015036000 Hexagon Head Screw M10 x 20.S.S. 9000100207 Sealing Washer M10 9030100289...
  • Page 28 Selwood Seltorque S100 Manual...
  • Page 29: Delivery Valve Parts

    Selwood Seltorque S100 Manual Delivery Valve Parts ITEM DESCRIPTION PART NUMBER Full Nut M16 9025160004 Spring Washer M16 9030160229 Delivery Valve Seat 0015046000 Delivery Branch Gasket 0015047000 Stud M16 9035160551 Delivery Valve Chamber 0010026001 T-Bolt 0015031000 Hexagon Bolt M16 x 65...
  • Page 30 Selwood Seltorque S100 Manual...
  • Page 31: Pump Body Parts

    Selwood Seltorque S100 Manual 7.4 Pump Body Parts ITEM DESCRIPTION PART NUMBER Impeller Screw 9000120302 Belleville Washer 9030510359 Impeller Washer 0010013000 Impeller 0010012000 Impeller Key 9041104013 Shaft Sleeve 0010161001 Sleeve 'O' Ring 9150001050 Mechanical Seal 9110038001 Pump Body 0010010001 Stud M12...
  • Page 32 Selwood Seltorque S100 Manual...
  • Page 33: Bearing Housing And Air Pump Drive Assembly Parts

    Selwood Seltorque S100 Manual 7.5 Bearing Housing and Air Pump Drive Assembly Parts ITEM DESCRIPTION PART NUMBER Hex. Socket Capscrew M8 x 25 9005080250 Spring Washer M8 9030080229 Lip Seal Carrier 0010200000 Lip Seal 9127040070 'O' Ring 9100308450 Bearing Housing 0010001201 Bearing Housing –...
  • Page 34 Selwood Seltorque S100 Manual...
  • Page 35: S100 / 7.5Kw 400/3/50 On Static Chassis - 1097206000

    Selwood Seltorque S100 Manual 7.6 S100 / 7.5kW 400/3/50 on Static Chassis - 1097206000 ITEM DESCRIPTION PART NUMBER S100 Pump Unit 0010901100 Spigot – 1.½” BSP 1589144000 Coupling Guard 0010194000 Guard End Plate - Pump 0010147000 Spigot 1589144000 Static Chassis...
  • Page 36 Selwood Seltorque S100 Manual Canopy, Item 3, removed for Clarity...
  • Page 37: S100 / 7.5Kw Supersilent Canopy Build - 1016133S40

    Selwood Seltorque S100 Manual 7.7 S100 / 7.5kW SuperSilent Canopy Build – 1016133S40 ITEM DESCRIPTION PART NUMBER S100/7.5KW on Static Chassis 1097206000 Skid Base Assembly 1016134000 Acoustic Canopy Assembly 1016135000 Removable Rear Top Door Assy 1015005000 Rear Bottom Panel Assy...
  • Page 38: Wiring Diagrams

    Selwood Seltorque S100 Manual 8 WIRING DIAGRAMS 8.1 3 Phase DOL...
  • Page 39: Ptc Thermistor Windings

    Selwood Seltorque S100 Manual 8.2 PTC Thermistor Windings...
  • Page 40: Space Heater

    Selwood Seltorque S100 Manual 8.3 Space Heater...
  • Page 41: Standard Terminal Box

    Selwood Seltorque S100 Manual 8.4 Standard Terminal Box...
  • Page 42: Axial Fan

    Selwood Seltorque S100 Manual 8.5 Axial fan...

Table of Contents