When establishing the electronic • Admin rights for installation Address) which is entered in the connection, observe the Additional memory capacity is DoorCom IP with the aid of the requirements of VDE 0805 / EN required for: configuration software. 60950.
3 Structure DCIP 740-0 Siedle Multi with link to system telephone Camera assignment mode PRI 602-... USB DCIP 740-... to 49 different call destinations The a/b public network interface is Siedle Multi link which correspond to the functions supplied from the TC system. It is of 49 Multi telephones.
3 Group calculation Monitor assignment mode Max. number of PC users PRI 602-... USB Commissioning and Performance features Calculation programming • Transmission of door calls with/ For calculation of the maximum After connection of the supply without video via the Ethernet to number of possible PC users (single voltage, the devices SIM 740-...
3 Terms Camera assignment registrations. In total, this adds up to 25*2=50, which is the maximum to 25*2=50, which is the maximum possible assignment per IPVS. A Siedle Multi door station can be possible assignment per IPVS. assigned up to 49 different PC users. In the following is a list with four This operating mode is only possible In the following is a list with five...
Page 7
Push to Talk Internet Protocol In case of a connection using the User Datagram Protocol The IP is a network protocol in half-duplex mode (push to talk) a The UDP is a minimal connectionless widespread use in computer button always has to be pushed to network protocol which belongs to networks.
Page 8
4 Components for DCIP 740-... Call buttons BTM 650-01 - BTM 650-04 Bus call button modules for In-Home bus. 1-4 call buttons, integrated LED lighting. Connection via ribbon cable to the TME 645-... Power supply to the LED lighting via terminals b and c with 12 V AC/DC, current consumption 25 mA per bus call button module BTM 650-...
4 Components for DCIP 740-... Input module, camera module CMC 612-... Camera module, colour. Integrated 2-step heating system, day/night switchover, infrared lighting and video signal transformer. Power supply using line rectifier NG 600-... or VNG 602-... With Siedle Multi via PCM 640-.../NG 600-..., NG 608-...
4 Components for DCIP 740-... Power supply, programming, video server NG 600-0 Line rectifier in 10-grid switch panel housing for universal power supply. Suitable for surface mounting with ZAP 10-0. Primary 230 V AC, 50 Hz, +6%-10% Secondary b/c: 14 V AC, 1 A; +/-: 24-28 V DC, 0.7 A Ambient temperature 0°C to +40°C, protection rating IP 20...
4 Device overview for DCIP 740-... Software DCIP SC 600-0 Client on a PC, a licence is required DoorCom IP Software Client PC for the DCIP SC 600-0. program, which depicts a virtual house telephone with video on a PC monitor.
4 Device overview only DCIP 740-... Siedle Multi SIVS 610-0 System interface video server, for connection of Siedle Multi to the IPVS 600-0. The SIM 740-0 is required for connection. The SIVS 610-... features galvanic isolation in addition to the SIVS 600-0.
Page 13
+M/-M Supply voltage Video 20 - 30 V DC Vc/- Actuation from door loudspeaker for camera on. With DoorCom IP the contact is permanently active. Potential - is switched via the UPS terminal. Actuation of camera distributor -M is switched...
5 Terminals DCIP 740-... Terminals and LEDs IPVS 600-0 a No function b Connecting socket to the SIVS 610-... c RJ45 socket ETH network connection d Reset button to recreate the as-delivered status (after a reset, the Siedle modes must be reinstalled, see page 30.) e LED operating status lights up in green on readiness for operation...
5 LED display SIVS 610-... /SIM 740-0 and IPVS 600-... LED signalling SIVS 610-... /SIM 740-0 Switching on LED green LED red Function After reset, power on: Device boots to operating status. The boot area is checked. Software runs in the flash Fast flashing After a software update, the boot area is recreated.
5 Terminals SIVS 610-0, SIM 740-0 Block diagram SIVS 610-0 Reference for the inputs E1–E4 not assigned not assigned not assigned not assigned Power supply for Vario bus, 15 V DC, max. 300 mA Da/Db Vario bus Supply voltage 24 V DC Tö...
Page 19
DCIP 740-... Siedle multi Remarks a) Door release 12 V AC, use at least Functional characteristics 20 Ohm (e.g. TÖ 615-...) Depending on the operating mode • 12 V AC consumers in the wiring camera assignment or monitor diagram: assignment, 49 or 4 PC users can •...
6 Commissioning DCIP 740-... Siedle multi The procedure for commissioning Connection of the PC to IPVS 600-... the DCIP 740-... is broken down into 4 steps: 1 Configuration of IPVS 600-... 2 Configuration of SIM 740-... 3 Configuration of SIVS 610-... 4 Installation of the software DCIP SC 600-...
Page 21
6 Configuration SIM 740-... Configuration of SIM 740-... SIM addresses Messages Programming the SIM 740-... takes In the mask SIM addresses, the In the Messages mask, status place using a connected PC via physical Multi bus addresses are messages are configured which are PRI 602-...
Page 22
6 Configuration Multicasting Multicasting The following settings must be If audio signals have to be Alongside the 1:1 connection performed separately in each transmitted in multicasting mode, between one IPVS 600-... and one IPVS 600-..these must be assigned to their software client (Unicast) each, the own port as this is a separate data IPVS 600-...
6 Configuration software DCIP CO 600-... Configuration of DCIP 740-... The configuration software DCIP CO 600-... is required for configuration of the SIVS 610-... and SIM 740-... Configuration takes place via a Windows PC. Connection to the SIVS 610-... takes place via the PRI 602-...
duplex • Input of the IP address of the IPVS 600-.. for which the configuration is applicable. This input is required to ensure that the Software Clients are able to locate the DCIP in the network. • Set Master-Monitor address. This is the main address on which the SIM 740-...
Page 26
6 Client-Software DCIP SC 600-... Installation of the Software Clients The Software Client DCIP SC 600-... must be installed on every PC you wish to receive door calls. The Software Client communicates with the calling station, the DCIP 600-... After installation, the file (*.dcip) generated using the configuration software must be imported.The...
Page 27
Possible error sources Other settings in the Software • No speech connection from the Client: PC to the door. The microphone amplifier may not be activated. Free buttons • Installation must take place as Selection of functions for buttons administrator, so that all registered 1–3.
7 Setting the speech volume Level adjustment DCIP 740-... Level adjustment IPVS 600-... Level adjustment TLM 645-... Level adjustment DCA 740-01 Setting the volume of the PC user in Setting the volume of the PC Set the volume of the speech the direction of the door station.
IPVS 600-..., it can be reset to the DoorCom IP and an analog connection from the exchange. It is as-delivered status. It is essential to telephone connection of a...
10 DoorCom IP FAQ and trouble shooting Is brokering possible at the PC? reached. (If a DNS server is entered Why does the DCIP SC 600-0.exe which is not reached, a number of software have to be enabled in the...
Page 32
10 Service Measured values Measurement values for DoorCom IP, to be measured using a digital multimeter Idle status min. max. Voltage +/- at line rectifier NG 608-... 24 V DC 28.5 V DC Voltage b+/c- at SIVS 610-... 15 V DC Voltage Da/Db at SIVS 610-...
Page 33
Index 11 Glossary Connection AEM 645-... The current issue of the “ DoorCom IP “ system manual is As-delivered status BTM 650-... available from the download area Block diagram CMC 612-... 9, 13 under www.siedle.de. Camera assignment 4, 6 COM 611-...