Epson S1R72U16 Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Motherboard
  5. S1R72U16
  6. Manual
Epson S1R72U16 Manual

Epson S1R72U16 Manual

Hide thumbs Also See for S1R72U16:
Table of Contents

Advertisement

Quick Links

Download this manual
S1R72U16
Evaluation Board Manual
Rev.1.10

Advertisement

Table of Contents
loading

Related Manuals for Epson S1R72U16

Summary of Contents for Epson S1R72U16

  • Page 1 S1R72U16 Evaluation Board Manual Rev.1.10...
  • Page 2 Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products.
  • Page 3 Scope This document applies to the “S1R72U16” IDE device - USB 2.0 host bridge LSI. Notice Before using the S1R72U16, carefully read the sections “Special use case for S1R72U16” and “S1R72U16 Errata.”...

  • Page 4: Table Of Contents

    Connection Example 1 (IDE I/F Connection Example) ............... 7 Connection Example 2 (CPUIF Connection Example) ............... 8 Connection Example 3 (CPUIF System Connection Example)........... 9 JP and SW Settings........................10 Circuit Diagram......................... 11 Component Chart ........................11 Dimensional Diagram ....................... 11 EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 5: Overview

    1. Overview 1. Overview This board is an evaluation board for the S1R72U16. This manual describes how to use the board. EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 6: Connector Connections

    CPU and making the settings described further below. 1pin 2pin 3pin N.C. 4pin N.C. Use Connector CN7 for RS-232 connections to a PC. Commercially-available RS-232 cross cables may be used. EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 7: Switches

    3. Switches 3. Switches Set the S1R72U16 operating mode using the DIP switches (SW1) provided on the board. SW1 (Factory default settings shown shaded) Switch Function selection Remarks ATA mode PORT00 pin = High No.1 Command system setting ATAPI mode...

  • Page 8: Leds

    Note: The pins of CN3 (not mounted) are connected directly to each PORT of the S1R72U16 as shown in the table above. These can be probed to monitor the signals for PORT10 to PORT 17. The output level will be the level supplied to the IOVDD pin.

  • Page 9: Jumper Pins

    MAX8586 automatic restart function selection 1-3: MAX8586-ENRESET pin = Low (Refer to Maxim data sheet for details) 1-2: Located at MAX8586-OUT pin JP10 USB host VBUS output 122 [uF] layout selection 1-3: Located at MAX8586-IN pin EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 10: Product Code

    6. Product Code 6. Product Code The product code for the board is as follows: S5U1R72U16F0100 EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 11: Appendix

    XHRESET_T Connect to connector if using with cable select. CSEL_T The cables and connectors described here should be replaced by circuit board wiring if the S1R72U16 is mounted on the system board (board designed by user). EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 12: Connection Example 2 (Cpuif Connection Example)

    GPIO RESET- XHRESET /CS, A[4] S1R72U16 addresses are word addresses. The addresses should be offset as necessary for connection. D[15:0] Add pull-up/pull-down resistors as necessary. A[3:1] S1R72U16 addresses are word addresses. The addresses should be offset as necessary for connection.

  • Page 13: Connection Example 3 (Cpuif System Connection Example)

    -（XHPDIAG_T） GPIO XHRESET /CS, A[4] S1R72U16 addresses are word addresses. The addresses should be offset as necessary for connection. D[15:0] Add pull-up/pull-down resistors as necessary. A[3:1] S1R72U16 addresses are word addresses. The addresses should be offset as necessary for connection.

  • Page 14: Jp And Sw Settings

    7. Appendix JP and SW Settings The factory default settings are shown below. SEIKO EPSON CORP. S1R72U16_EVA_QFP BOARD CLKSEL +3.3V HVDD LVDD +1.8V IOVDD SELECT 1-2:IOVDD +3.3V 2-3:IOVDD +1.8V EPSON S1R72U16 Evaluation Board Manual (Rev1.10)

  • Page 15: Circuit Diagram

    Component Chart Refer to the chart included at the end of this document. Dimensional Diagram 80.00 4.00 4.00 SEIKO EPSON CORP. S1R72U16_EVA_QFP BOARD CLKSEL +3.3V HVDD LVDD +1.8V IOVDD SELECT 1-2:IOVDD +3.3V 2-3:IOVDD +1.8V EPSON S1R72U16 Evaluation Board Manual (Rev1.10)
  • Page 16 Revision History Revision History Revision details Date Rev. Page Type Details 06/06/2007 1.00 Newly established 10/15/2007 1.10 Scope Added “notice.”...
  • Page 18 S1R72U16 QFP EVA BOARD RoHS Parts List Attention： A red letter of 'Reference' is nonimplement. PartName Quantity Maker Value Rating Tolerance Reference GRM188R11H104JA01 12 Murata 0.1u 5% C1,C2,C3,C4,C5,C12 ,C13, C19,C20,C21,C23, GRM1882C1H150JZ01 2 Murata 5% C14,C15 EMVA160ADA220MD55G 1 NIPPON CHEMI-CON 20% C22 GRM188F11A105ZA01 11 Murata -400 C6,C7,C8,C9,C10, C11,C16,C17,C18,...
  • Page 19 80992 Munich, GERMANY Hi- Tech Park, Shenzhen Phone: +49-89-14005-0 FAX: +49-89-14005-110 Phone: +86-755-2699-3828 FAX: +86-755-2699-3838 EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110 Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD. 1 HarbourFront Place,...

This manual is also suitable for:

S5u1r72u16f0100

Table of Contents