Advertisement
NAMES OF CONTROLS
1. Handle
13. CD display
2. CD door
3. STOP
button
4. PLAY / PAUSE
button
5. FUNCTION switch
6. VOLUME control
7. PHONES
jack
8. Fixed antenna
14. BAND switch
9. Tuning control
10. SKIP
15. AC socket
button
16. Battery compartment
11. REPEAT
button
12. SKIP
button
POWERING UP
AC POWER
You can power your portable stereo system by plugging the detacha-
ble AC power cord into the AC inlet on the back of the unit and into a
wall AC power outlet.
Check that the rated voltage of your unit matches your local voltage.
Make sure that the AC power cord is fully inserted into the unit.
Caution: (for USA)
To prevent electrical shock, match
wide blade of plug to wide slot,
fully insert.
Note:
When not being used on mains the
AC Cord should be unplugged
from the unit.
To wall AC outlet
BATTERY POWER
Insert 6 "C" size batteries in the battery compartment. Be sure that the
batteries are inserted correctly to avoid damage to the unit.
• Always remove the batteries when unit will not be used for a long
period of time, as this will cause leakage of the batteries and
subsequently damage to your unit.
• Playback will automatically come to a stop when the batteries have
no more power. Replace all the batteries with new ones.
• Do not mix old and new batteries. Do not mix ALKALINE, standard
(CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries.
Track number
Play " " indicator
Pause "
" indicator
Repeat all " " indicator
Repeat one "
" indicator
To AC inlet
ADJUSTING THE SOUND
VOLUME
Adjust the VOLUME control of the stereo system to a desired level.
For private listening
Connect headphones (Ø 3.5 mm stereo mini-plug) to the PHONES
When only headphones are connected the speakers are automatically
disconnected.
RADIO OPERATION
You can listen to your favourite radio stations by sliding the FUNCTION
switch to RADIO, and then
1. Slide the BAND switch to choose AM(MW) or FM.
2. Using the TUNING control to choose a desired station.
• Adjust the VOLUME.
AM(MW)/FM
• Repositioning the unit to get better AM(MW)/FM reception.
Note
When you have finished listening, slide the FUNCTION switch to OFF.
USING THE CD PLAYER
1. Slide the FUNCTION switch to CD. "
2. Open the CD door. Place a disc in the centre with the label side
up and then close the CD door gently. The total number of tracks
will show in the display.
3. Press the PLAY/PAUSE
indicator will light.
• Adjust the VOLUME.
TO STOP PLAYBACK
• Press the CD STOP button to stop disc play.
TO INTERRUPT PLAYBACK
• Press the PLAY/PAUSE
play (the PAUSE "
" indicator will blink).
• Press the PLAY/PAUSE
TO SKIP TO THE BEGINNING OF A TRACK
• Press either one of the SKIP
direction. Each press skips one track. During play, the first press on
the skip backwards
button to the beginning of the current track.
• Playback resumes from the selected track.
TO SEARCH THROUGH TRACKS
• Keep either one of the SKIP
the desired direction, and release at the desired point.
REPEAT PLAY -- in play modes
This function allows one track or all tracks on a disc to be played repeatedly.
TO REPEAT THE SAME TRACK
• Press the REPEAT button once during playback, the REPEAT ONE
"
" indicator will blink.
TO REPEAT THE WHOLE DISC
• Press the REPEAT button a second time to repeat all tracks, the
REPEAT ALL " " indicator will light.
TO CANCEL REPEAT PLAY
• Press the REPEAT button until the REPEAT indicator is turned off.
Note
Repeat play can only be done when the unit is in the play mode.
" is shown in the display.
button to start play. The PLAY " "
button while a CD is playing to pause
button again to resume play.
or
button according to the desired
or
button pressed, according to
jack.
Advertisement
