Do you have a question about the Molift Nomad and is the answer not in the manual?
Questions and answers
Madelyn Morgan
February 10, 2025
Why is the red light on the front by the wrench symbol staying on?
2 comments:
Madelyn Morgan
February 10, 2025
Madelyn Morgan
Mr. Anderson
February 11, 2025
The red light by the wrench symbol on the Etac Molift Nomad indicates that the lifter requires service. If the red light is accompanied by a sound, it means the service is needed immediately.
Before using the patient lifter version of the product, are not permitted. Etac Before using a patient lifter, the operator must be Supply Gjøvik will accept no liability for damages trained accordingly.
Injury to personnel or equipment may occur if gards to safety. Molift NOMAD is used in an incorrect manner and All instruction and information in this manual re- garding safety and general precautions must be •...
About the product Safety devices Molift NOMAD is equipped with several safety de- Molift NOMAD is a portable ceiling lifter intend- vices, which are intended to prevent personal in- ed for lifting and transferring persons. The lifter jury or damage to equipment in the case of incor- is made out of light materials and has a battery.
Assembly/disassembly • Reset the emergency stop button. Checklist after mounting To be able to operate the Molift NOMAD, the oper- ator must have good knowledge of the lift, includ- • Check that the lifter has no visible damage or ing assembly and preparation before use.
Etac Supply Gjøvik. Service light Battery care Contact hand control The batteries of the Molift NOMAD is a 26,4 V cell Hand control unit that is placed inside the chassis. Operating the lifter The lifter has a battery light on the hand control...
Charging The battery will not achieve full capacity be- The charger can be placed on the wall or a table fore it has been fully charged and discharged and connected to the power outlet. The Charger a couple of times. must be placed or installed in a way that makes it easy to disconnect mains cable.
Please see the user manual following each sling for specific user instructions. The lifter is only to be used for transferring over short distances. It is not a replacement for wheelchairs or similar. Page 10 of 20 BM15101 Molift NOMAD English - Rev. M 23-08-2013...
Climbing • Lower the lifter until it hangs in the climbing With Molift NOMAD it is possible to climb between belt only. two rail systems, and then we can avoid cut-outs above the doors. There must be a trolley with a The lifter will stop if the lifting belt is untight.
Make sure that the rail system has the same max. load as the lifter, 255 kg. If the Molift NOMAD is mounted on a rail sys- Trolley Molift Nomad (SWL 255 kg) tem with a lower lifting capacity, the lowest Part number 1109400 capacity also applies for the lifter.
Page 13
Trolley for Molift open rail Trolley Molift Nomad Part number 1210001 Trolley with swivel and a climbing belt that makes it possible to climb between two different rail sys- tems. When necessary it is possible to have a trolley with a suspended attachment hook.
Art. no 3036300 100-150 cm Art. no 3023200 Art. no 3024200 Art. no 3023300 Art. no 3024300 Art. no 3023400 Art. no 3024400 Art. no 3023500 Art. no 3024500 Page 14 of 20 BM15101 Molift NOMAD English - Rev. M 23-08-2013...
Please see the user manual following each sling for specific user instructions. Sling bag Bag for slings - Art. no 3048000 Molift NOMAD Attachment arm Extension Arm I 900 - Art. no 1200004 Extension Arm I 1050 - Art. no 1200006 Scale Scale set - Art.
Contact local service representative/ charging Reset emergency stop dealer or Etac Supply Gjøvik if the lifter does Plug for charger is not con- not work properly or if the service light illumi- nected to power (no light on nates.
Service Labelling On the front right side of the lifter there is a service Explanation of the lifters labelling: light which will give a signal when the lifter needs Controlled Part number Serial number service. When there is a green light, the lifter can and approved be used normally.
Inspection carried out by: (Block capitals) ........from ..............Molift certification no. for inspector/repairer (if any): ....................The equipment has been tested and is in full working order Place: ........Date: ....Signature:.................... Page 18 of 20 BM15101 Molift NOMAD English - Rev. M 23-08-2013...
Need help?
Do you have a question about the Molift Nomad and is the answer not in the manual?
Questions and answers
Why is the red light on the front by the wrench symbol staying on?
Madelyn Morgan
The red light by the wrench symbol on the Etac Molift Nomad indicates that the lifter requires service. If the red light is accompanied by a sound, it means the service is needed immediately.
This answer is automatically generated