Advertisement
REMOVING DEVICE FROM ZigBee NETWORK (FACTORY RESET)
To remove the PIR Camera from current ZigBee network, the PIR Camera must be put to Factory Reset to complete device removal. Factory Reset
function will clear the PIR Camera of its stored setting and information and prompt the PIR Camera to search for new ZigBee network.
Before removing device, make sure the PIR Camera is within current ZigBee network signal range
Step1.
Delete the PIR Camera from current control panel / CIE.
Step2.
The PIR Camera can only be reset within 3 minutes after power up. If the PIR Camera has been powered up for more than 3 minutes,
remove and reinsert the battery.
Step3.
Make sure the tamper switch is open (released), press and hold the function button for 10 seconds, then release the button to reset
PIR Camera.
Step4.
Upon reset, the PIR Camera will clear current ZigBee network setting and transmit signal to ZigBee coordinator to remove itself from
current ZigBee network. It will then actively search for available ZigBee network again and join the network automatically.
5
INSTALLATION
INSTALLATION GUIDELINE
The PIR Camera is designed to be mounted on either a flat surface or in a corner situation with fixing
screws and plugs provided.
The base has knockouts, where the plastic is thinner, for mounting purpose. Two knockouts are for
surface fixing and a triangular mounting bracket is used for corner fixing.
It is recommended to install the PIR Camera in the following locations.
Mount where the animals cannot come to the detection area by climbing on furniture or other objects.
Don't aim the detector at stairways the animals can climb on.
In a position such that an intruder would normally move across the PIR's field of view.
Between 1.9 and 2 m above ground for best performance. When mounted at 1.9 m above ground, it
gives a typical PET IMMUNE range of 7 m. As the PIR Pet-Immune Camera is higher from above ground, it gives a farther PET IMMUNE
range.
In a corner to give the widest view.
Where its field of view will not be obstructed e.g. by curtains, ornaments etc.
For a small 3 to 5 m room, install between 1.9 to 2 m above ground.
Limitations
Do not position a PIR Camera to look directly at a door protected by a Door Contact, this could cause the Door Contact and PIR Camera radio
signals to be transmitted at the same instant when entering, canceling each other out.
Do not install the PIR Camera completely exposed to direct sunlight.
Avoid installing the PIR Camera in areas where devices may cause rapid change of temperature in the detection area, i.e. air conditioner,
heaters, etc.
Avoid large obstacles in the detection area.
Not pointing directly at sources of heat e.g. Fires or boilers, and not above radiators.
Avoid moving objects in the detection area i.e. curtain, wall hanging etc.
USING PIR CAMERA WITH ZigBee ROUTER
NOTE>>
If PIR Camera installation location is away from your system control panel and requires ZigBee routers to improve signal strength. DO NOT
use a ZigBee Router without backup battery. A ZigBee router without battery will be powered down during AC power failure and the PIR
Camera connected to the router will lose connection with ZigBee network. Plan your PIR Camera installation location using only ZigBee router
with backup battery.
MOUNTING THE PIR CAMERA
Surface mounting
Step1.
Remove the cover by loosening the Cover Screw using a Philips screwdriver.
Step2.
Break through the 2 Surface knockouts at the center of base.
Step3.
Use the holes as template to drill holes on the surface.
Step4.
Insert the wall plugs if fixing it into plaster or brick.
Step5.
Screw the base into the wall plugs.
Step6.
Fit the cover onto the base and tighten the Cover Screw using a Philips screwdriver.
Corner mounting
Step1.
Break through the two knockouts on the triangular bracket.
Step2.
Use the two holes as template to drill holes on the corner surface.
Step3.
Insert the wall plugs.
Step4.
Screw the triangular bracket into the wall plugs with the two pointing sticks on top facing you.
Step5.
Fit the PIR Camera onto the hooks of the triangular bracket.
6
APPENDIX (FOR DEVELOPERS ONLY)
PIR CAMERA CLUSTER ID
Device ID: _852_DEVICEID: 0x404 (proprietary)
Endpoint: 0x01
Server Side
Basic (0x0000)
IAS Zone(0x0500)
_852_Cluster(0x0503) (proprietary)
Mandatory
Optional
Client Side
None
None
Advertisement
