Related Manuals for FLAIM Systems Extinguisher
Summary of Contents for FLAIM Systems Extinguisher
- Page 1 FLAIM ™ Extinguisher User Manual September 2020 Copyright © 2020...
- Page 2 Welcome to the FLAIM community! Proper skills and early response to fire saves lives! FLAIM Extinguisher immerses trainees in virtual reality, delivering a realistic simulation of a range of fire events to efficiently train first responders PASS...
-
Page 3: Table Of Contents
Contents What’s in the Box Quick Start Guide Training Instructor Viewing System Set-up Troubleshooting How to Use Flaim Extinguisher Getting Started Streaming to Video Screen (Projector or Television) Selecting Scenarios Running Scenarios Training Options Extinguisher Training Extinguisher Tab Technique Tab... -
Page 4: What's In The Box
FLAIM Extinguisher PASS What’s in the box? Please see below images of the individual parts that come in your FLAIM Extinguisher box/case (Figure 1 and 2) with an explanation of what they do. Figure 1: FLAIM Extinguisher System box (case) - Page 5 Description Picture VR headset - Pico neo2 Head Mounted Display Extinguisher controller tracking system Power cable for Head Mounted Display HDMI receiver Charge plug (country specific) for charging Pico neo2 Headset Country specific power cable and power adaptor for HDMI receiver power supply (configuration...
-
Page 6: Quick Start Guide
The training instructor viewing system (Figure 3) receives the signal transmitted by the FLAIM Extinguisher VR headset. It allows the training instructor and others in the room to experience a live view of what the person being trained can see in the virtual training environment. - Page 7 Step 1 Figure 4: Ensure HDMI receiver is powered 1. Plug the micro USB lead into the USB port on (Blue light) – top right your television and projector. 2. When powered, the receiver power light will glow blue (see Figure 4). The USB Power supply delivers power to the HDMI receiver.
- Page 8 5. The user now needs to adjust the lens on the base of the VR headset to improve the visual clarity. Step 4: Powering on the Extinguisher controller tracking system. • Short press the HOME buttons (Figure 6 and Figure 7) to wake up the two controllers.
-
Page 9: Set-Up Troubleshooting
Set-up troubleshooting Controller Calibration The two extinguisher tracking controllers are pre-calibrated. There is no user need to calibrate. If you find either of the controllers has drifted, and you cannot see the controller from inside the headset, point the controller horizontally to the front of your field of view, and press and hold the HOME key for more than one second to re-center the controller.Reset with VR headset (trainee) -
Page 10: How To Use Flaim Extinguisher
How to Use FLAIM Extinguisher Getting started Once the system is turned on the initial Extinguisher lobby screen will appear within 1 minute... -
Page 11: Streaming To Video Screen (Projector Or Television)
3. You should see Connecting you now on your television or projector. Magic is about to happen. It may take 10-20 seconds to connect. 4. FLAIM Extinguisher will now be streaming to the television or projector. It will show what the VR headset view. -
Page 12: Selecting Scenarios
Selecting the scenario category (Figure 10) 1. Select CATEGORIES 2. Select the preferred environment category 3. Once you enter you will find a selection of learning scenarios as exampled below Figure 10: Environments and Scenario menu... -
Page 13: Running Scenarios
Running scenarios 1. Select a scenario by pointing and holding down the bottom button on the controller. 2. You will now see a circle at your feet (Figure 11). 3. Step into the centre, with the same orientation as shown. 4. -
Page 14: Training Options
Extinguishers Tab (next to the Scenarios Tab) To run this training option, follow the steps below: 1. Select an extinguisher, it will then appear in the user’s hand. 2. The user should press the trigger or top button on the controller to use the extinguisher. -
Page 15: Technique Tab
Technique Tab The Technique Tab (Figure 15) walks users through the extinguisher PASS technique. Ie: Pull the pin, Aim at the base of the fire, Squeeze the handle and Sweep from left to right. To see the next step - switch pages using the right arrow. - Page 16 Figure 15: PASS Technique - Pin Figure 16: PASS Technique - Aim...
- Page 17 Figure 17: PASS Technique - Squeeze Figure 18: PASS Technique - Sweep...
-
Page 18: Fault Finding
WIFI signal to check whether the WIFI works normally. 4. Find none of the above steps resolve the problem, please contact FLAIM. FLAIM Systems maintains a support team via email at support@flaimsystems.com and will respond within 24 hours about any further technical issues. -
Page 19: Safety
Please read the supplied PicoNeo 2 manual for care and maintenance tips. Further Support Thank you for choosing our FLAIM Extinguisher product to use as a part of your training program. For further support, please contact your local distributor or in- country agent during business hours or email support@flaimsystems.com... - Page 20 flaimsystems.com info@flaimsystems.com Copyright © 2020...