Table of Contents
Advertisement
Quick Links
1
Introduction of the fingerprint lock .................................... 3
1.1
Feactures .................................................................................... 3
1.1.1 Brief Introduction ......................................................................... 4
1.1.2 Introduction of functions ............................................................. 4
1.2
Diamensions ............................................................................... 5
1.3
Technical data ............................................................................. 5
2
Operation .............................................................................. 7
2.1
Door opening pattern .................................................................. 7
2.2
Ways to put the finger ................................................................. 7
2.3
Setting Card + password ............................................................ 8
2.4 Setting fingerprint + password + card ........................................... 9
2.5 Alarming Function .......................................................................... 11
2.5.1 Low voltage alarm ..................................................................... 11
2.5.2 Preventing dismantling alarm .................................................. 11
2.6 Backup power ................................................................................ 12
2.7 Installing / replacing batteries ........................................................ 12
2.7.1 Installing batteries ..................................................................... 12
2.7.2 Replacing batteries ................................................................... 12
2.8 Remarks ........................................................................................ 13
3
Installation Procedures ..................................................... 13
3.1
Opening pores on the door ....................................................... 13
3.2
Opening pores on lock holder case .......................................... 14
3.3
Installation procedures ............................................................. 14
3.3.1 Installing lock cylinder ......................................................... 14
3.3.2 Installing the front and back lock body ................................ 15
3.3.3 Installing buckle and frame in door case ............................ 16
4
Maintenance and upkeep .................................................. 17
Contents
1
Advertisement
Table of Contents
Related Manuals for Joney JYF-3001
Summary of Contents for Joney JYF-3001
-
Page 1: Table Of Contents
Contents Introduction of the fingerprint lock ........3 Feactures ..................3 1.1.1 Brief Introduction ................. 4 1.1.2 Introduction of functions ............. 4 Diamensions ................5 Technical data ................5 Operation ................7 Door opening pattern ..............7 Ways to put the finger ..............7 Setting Card + password ............ - Page 2 Daily maintenance and upkeep ..........17 Notice for use ................18 After-sale Service ............... 20 Remarks about after-sale service..........20 Packing List ................21 Accessories ................22 A/2(2014 年 1 月)
- Page 3 Important Tips 1. Fingerprint lock is a kind of hi-technical product, and its normal operation and life span are directly influenced by the installation. Therefore, we kindly suggested you to call in a professional to install it. Please open pores, supporting pits, buckle and buckle pores according to the indication of opening pore in the door plank.
- Page 4 Registration Form of Users For convenience, we make this form for administrator to record information of user registration. You can also make you form according to your specific requirements. Fingerprint Date of Department Name signature Remarks registration...
-
Page 5: Introduction Of The Fingerprint Lock
1 Introduction of the fingerprint lock 1.1 Feactures Front Sliding Cover Nixie Tube and Induction window Fingerprint Scanner Keypad Front Lock Body Front Handle Sliding Cover Eternal Power Interface Back Cover 1 8 pieces of AA batteries Screw plug Back Lock Body Back handle Back Cover 2 Deadlock knob... -
Page 6: Brief Introduction
1.1.1 Brief Introduction Features : Delicate appearance design, Reasonable structure, Secure fingerprint lock. Applications: Government, Police station, Army, Bank, Law Court, Hospital, Office building, Residential area, etc. 1.1.2 Introduction of functions We adopt the international advance biotechnology to ensure its high quality; 8 peaces AA batteries;... -
Page 7: Diamensions
1.2 Diamensions 1.3 Technical data Items Technical parameters Sensor resolution Bright background, 500dpi Sensor damage resistance 1000 times of impact with 4H pencil ability Starting time <1 second Way of contrast 1：N ≤1% False rejection rate ≤0.0001% Error rate Finger point 360°... - Page 8 treatment Static Power Consumption < 30 The working current is under Dynamic Power Consumption Dicaryon dual circuit and individual Control system control The fingerprint battery life Open door for 5000 times The combination battery life Open door for 6000 times Working voltage DC 6 V Power supply mode...
-
Page 9: Operation
2 Operation 2.1 Door opening pattern Open Left Side Open Right Side Open left side: If you stand outside the door, the fix butt hinge is in the left, so you have to hold the handle with your left hand. And when you open the door, the lock is opened from the left. -
Page 10: Setting Card + Password
手指须放置在指纹采集窗中心 保持手指平放在指纹采集窗 轻轻地把手指按在指纹采集窗 保持平稳（不要向前或向后滑） Lock-out function 反锁功能 Pull the handle upwards inside or outside the door can make it lock out and realize the function of anti-theft bolt. Rotate the small knob in the back of the lock 45 degrees, the door will be deadlock, and it cannot be opened outside in any ways. -
Page 11: Setting Fingerprint + Password + Card
times. Next you will hear 3 long sounds and see the green light off, then you can release the handle. Reading any administrator cards or guest cards can cancel the keep-open state. 2.3.5 Setting administrator password: After initialization, put in 6 digits numbers and then press the LOCK, this 6-digit number is the administrator password. - Page 12 Operation Instructions： Initialization: long-press the switch of initialization on the circuit board and do not loosen your finger until you hear the voice prompt of “……has cleared”. And the initialization will be finished. At this moment there is not any effective cards or fingerprints and the administrator password is 123456.
-
Page 13: Alarming Function
” to enter the programming mode. Next, press 5 + and put in the 2-digit password number you want to delete and end up with pressing Repeat the 2-digit number + LOCK and the password is deleted Setting keep-open state: Opening the lock by fingerprint or password, press the handle to keep opening the door for 6 seconds until you hear the voice prompt of “the door is in the keep-open state”. -
Page 14: Backup Power
2.6 Backup power When the batteries is totally out of power and mechanical keys are not available at the same time, please connect the 9V layer-built battery to the power interface under the front lock body to power the combination, and then put in password to open it. -
Page 15: Remarks
2.8 Remarks 2.8.1 When you add a new user, please do record the user number for administration. 2.8.2 instruction sound remarks: The voice prompt of “successful” means successful operation, while voice prompt of “failed ” means failed operation. 3 Installation Procedures 3.1 Opening pores on the door This product can be used in wooden doors and anti-theft doors with thickness over 40MM. -
Page 16: Opening Pores On Lock Holder Case
3.2 Opening pores on lock holder case Open pores as below. Make sure they keep accordance with the lock and parallel with the door case when locking. 3.3 Installation procedures Before installation, please put through all of the connecting wire, press the initialization button on the circuit board to initialize the lock firstly, which will also delete all of the passwords, cards and fingerprints to restore the factory setting. -
Page 17: Installing The Front And Back Lock Body
天地拉杆根据需要上下调动 锁芯固定螺丝 FA4*25 锁头固定螺丝 FM5*65 机械锁头 天地拉杆根据需 要上下调动 3.3.2 Installing the front and back lock body Before installing the lock body, please check if the handle springs fall off, and put the handle square shafts into the lock cylinder. Please notice the directions of opening left and opening right: the downwards arrow is for opening right and upwards for left. -
Page 18: Installing Buckle And Frame In Door Case
8节5号碱性电池 密码指纹锁后板 胶塞-螺丝盖*2 前面板3P连接线插头 密码指纹锁前板 （与后板连接） 后面板3P电源线 圆头十字M3*8(*2) 后面板电池盖1 后面板电池盖2 后把手弹簧 把手方轴 反锁旋钮 前把手弹簧 反锁旋钮方轴 取下外 前后固定FM5*50(根 盖，可 据门厚调整）*4 使用外 接电源 和机械 钥匙 3.3.3 Installing buckle and frame in door case Put the frame in door case, next cover the buckle, and then fix them with 4 screws. -
Page 19: Maintenance And Upkeep
门框 门框盒 门扣板 4 Maintenance and upkeep 4.1 Daily maintenance and upkeep 1、 keep the lock away from corrosives which can damage the protection layer and the luster on the lock. 2、The handle is the key part to open and close the door, and its flexibility will directly affect the use of the lock. -
Page 20: Notice For Use
9. Do not use your fingernail to scratch the fingerprint reader. 10. Please use soft cloth to wipe the fingerprint scanner surface when it is wet. 11. When acquiring the fingerprint, please put your fingerprint on the scanner flatly. 12. If the lock cannot rotate smoothly or in the wrong place, please ask a professional to add some machinery oil. - Page 21 product. Elimination: clean the finger with tissue and then put it on the scanner to unlock the door. Or open the door by password or mechanical key. F. Put the finger on the scanner too lightly to scan most of the fingerprint. Elimination: Put the finger on the scanner correctly to unlock the door.
-
Page 22: After-Sale Service
A. The clutching parts are out of work. ( Too much oil on the clutch and flows into the elevator so that the elevator can not run well.) B. 1. Length of the handle square shaft is not suitable. 2. The spring of the handle in the back cover falls off. -
Page 23: Packing List
（1）Products are beyond the maintenance deadline or purchased through irregular way. （ 2 ） Damages caused by improper operation, dissembling the cover, man-made sabotage or other force majeure. （3）Locks repaired in unassigned maintenance stations. 5.1.3 Life-long maintenance. Maintenance after one year will be charged. 5.2 Packing List Items Quantity... -
Page 24: Accessories
5.3 Accessories frame in door case Door buckle Screws: PA4.0X25 Square shaft of handle Bolts: OM8.0XM5XL Square shaft for lock-out Mechanical cylinder Mechanical keys: 2pieces...
Need help?
Do you have a question about the JYF-3001 and is the answer not in the manual?
Questions and answers