MC Crypt TM-8017 Operating Instructions page 2

LED Mirror Ball Station TM-8017
Item no. 59 11 70
Intended Use
This mirror ball will add fun and colour to any dance floors, stages, party room etc. It features two multicolour
LED spotlights with four base LEDs. The mirror ball gently rotates, throwing dazzling circles of light into every
corner of your room. It can be mounted on a desk or hung up with the built-in bracket. It is only authorized for
dry indoor use and should be powered by the included adapter.
Unauthorised conversion and/or modification of the device are inadmissible because of safety and approval
reasons (CE). Any usage other than described above is not permitted and can damage the product and lead to
associated risks such as short-circuit, fire, electric shock, etc. Please read the operating instructions thoroughly
and keep them for further reference.
Delivery Content
• LED mirror ball station
• Power adapter
• Operating instructions
Safety instructions
We do not assume liability for resulting damages to property or personal injury if the
product has been abused in any way or damaged by improper use or failure to observe
these operating instructions. The warranty/ guarantee will then expire!
The icon with exclamation mark indicates important information in the operating
instructions. Carefully read the whole operating instructions before operating the device,
otherwise there is risk of danger.
Persons / Product
• The product is not a toy and should be kept out of reach of children!
• Do not leave packing materials unattended. These may become dangerous playing material for children.
• Never pour any liquids above the lamp. You run the risk of causing a fire or a fatal electric shock. If liquid
enters device, immediately disconnect it from the power supply and contact a specialist.
• The power adapter should never be plugged or unplugged with wet hands.
• Do not touch the mirror ball when it is rotating.
• When used in conjunction with other devices, observe the operating instructions and safety notices of
connected devices.
• The product must not be subjected to heavy mechanical stress.
• The product must not be exposed it to extreme temperatures, direct sunlight, intense vibration, or
dampness.
• Never operate the mirror ball without supervision.
• Do not look straight into the light rays during operation. The light rays could cause brief visual problems.
For epileptics particularly, epileptic fits could be triggered under certain circumstances.
• If there is reason to believe that safe operation is no longer possible, the device is to be put out of operation
and secured against unintended operation. Safe operation is no longer possible if the device:
- shows visible damages,
- no longer works,
- was stored under unfavourable conditions for a long period of time or
- was subject to considerable transport stress.
Miscellaneous
• Servicing, adjustment or repair works must only be carried out by a specialist / specialist workshop.
• If any questions arise that are not answered in this operating instruction, contact our Technical Advisory
Service or other experts.
Installation
• If the device is to be hung up, it should be secured additionally by a second safety
suspension (e.g. a safety arrester cable) which is independent of the actual mounting
bracket. If the main suspension fails, the device should not fall down. Also, make sure
that the area below it is blocked off in case that it falls.
• The device should never be part of a free-swinging system.
• The area or equipment, which the device is to be hung on, must be able to support ten
times the weight of the device for at least an hour without permanent deformation.
• The mirror ball must be positioned so that it can freely rotate. It must not come into
contact with other surfaces or objects under any circumstances.
• Never position the product in the vicinity of combustible or easily flammable materials
(e.g. curtains, decorative materials etc.). Maintain a free space of at least 50 cm around
the device with good air circulation.
• The maximum permissible environment temperature of 45°C may not be exceeded.
• This device should not be used for permanent lighting. Operation over an extended
period of time may decrease the service life of the product.
1. Place the mirror ball on your desktop or any flat surface. Alternatively, you can hang it up with the built-in
bracket at the bottom of the unit.
2. Connect the adapter cable to the base of the mirror ball.
3. Connect the adapter plug to the mains outlet.
4. To switch the mirror ball on or off, press the button on the base.
5. The mirror ball starts rotating once the power is connected. The two spotlights at the side can be freely
adjusted.
Cleaning
Use a dry and lint-free cloth to clean the product. For more resistant stains, use a cloth that is slightly moistened
with lukewarm water.
Disposal
Version 04/12
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Technical data
Operating voltage:
Input voltage:
Maximum power consumption:
Operating temperature:
Operating humidity:
Storage temperature:
Storage humidity:
LED colours:
No. of LEDs on base:
No. of LEDs in lamps:
Cable length:
Dimensions (W x H x D):
Ø Mirror ball:
Weight:
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
12 V/AC, 670 mA (mirror ball)
230 - 240 V/AC, 50 Hz (adapter)
8 W
-10 to +45 °C
10 – 97 %
-15 to +60 °C
10 – 97 %
red / blue / green
4
6 per lamp
approx. 1.8 m
26.3 x 13.5 x 23 cm
12.5 cm
817 g
V3_0412_02-HL