Sony XAV-AX150 Service Manual page 6

XAV-AX150
2. Setting of Destination Code
After checking the destination code,
according to procedure below, be sure to set the correct
not displayed,
destination code.
Setting procedure:
1. Press the button on the remote commander in order of [
[ ] t [ENTER], enter the destination code setting mode and
.
the left most digit of "Destination Code" change to red (cursor
for edit) and blinks.
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
2. Input the 6 digits destination code "00D442".
Press the [ V ] or [ v ] button on the remote commander, and select
the alphanumeric character of "0 to F".
Note 1: The destination code cannot be inputted by operation of main unit.
Be sure to input the destination code by using the remote commander.
Note 2: The number buttons on the remote commander cannot be used.
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
The cursor advances by pressing the [ENTER] button on the
remote commander.
The position of the cursor can not be returned.
If you have advanced the digits by mistake, press the [ENTER]
button repeatedly until the cursor moves to the position you
want to modify.
(The cursor disappears when press the [ENTER] button at the
right most digit, and when press the [ENTER] button again, the
cursor appears at the left most digit)
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
3. After inputting the right most (sixth) digit, set value is memo-
rized by pressing the [ENTER] button on the remote command-
er, then the cursor disappears and returns to white.
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
6
if the correct destination code was
>
1242
1243
3730
1806011349
X X X X X X
12:34:56:78:90:AB
Red blinks
1242
1243
3730
1806011349
0 X X X X X
12:34:56:78:90:AB
Press [V] or [v] button
to select "0 to F".
Press [ENTER]
button, move
1242
the cursor.
1243
3730
0 X
1806011349
0 X X X X X
12:34:56:78:90:AB
0 X
Press [ENTER]
button, cursor
1242
disappears.
1243
3730
4 2
1806011349
0 0 D 4 4 2
12:34:56:78:90:AB
4 2
4. Press the [OFF] button on the remote commander, the unit auto-
matically restarts and return to the "Initial Setting" screen.
Touch the [OK], the screen changes to the "For your safety"
screen and then the home screen is displayed.
CPU Version 1242
] t
MCU Version 1243
DSP Version 3730
OSD Version 1806011349
Destination Code 0
BD ADDRESS 12:34:56:78:90:AB
For your safety screen
1:00 AM
For your safety:
Do not watch and operate the unit while driving.
Follow your local traffic laws and regulations.
Close
(Displayed screen in the above fi gure are example)
5. Press the [HOME] button on the main unit.
– Lower side of front panel –
Press the [HOME] button
6. Press the [OFF] button on the remote commander to the state of
source off , enter the destination code checking mode by pressing
the buttons on the remote commander in order of the [4] t [5]
t [6] (press only the [6] button for two seconds).
(Displayed screen in the above fi gure are example)
7. Check the destination code of 6 digits on the screen display is a
value set in step 2.
Note 3: If the setting is incorrect, start from step 1 again.
(Displayed characters/values in the above fi gure are example)
Sony CONFIDENTIAL
For Authorized Servicer
0 D 4 4 2
Initial Setting screen
1:00 AM
Initial Setting
Language
Demo
Set Date/Time
Touch the [OK]
Source off (HOME screen)
AM
Tuner BT Audio Phone USB Rear Camera
CPU Version 1242
MCU Version 1243
DSP Version 3730
OSD Version 1806011349
Destination Code 0 0 D 4 4 2
BD ADDRESS 12:34:56:78:90:AB
check
– Continued on next page –
English
ON
01/01/2018
OK
SYS SET