Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cognex DSMax
Summary of Contents for Cognex DSMax
- Page 1 ™ DSMax 32T-CXP Basic Safety and Usage 2020 April09 Revision: 9.6.0.SR1.2...
- Page 3 (ESD), power surges, or other irregularities in the power supply. Do not install Cognex products where they are exposed to environmental hazards such as excessive heat, dust, moisture, humidity, impact, vibration, corrosive substances, flammable substances, or static electricity.
-
Page 4: Sensor Layout
Sensor Layout... -
Page 5: Specifications
Specifications Refer to the following table for DSMax sensor head specifications: Specification DSMAX Sensor Head Dimensions 133.4 mm (H) x 65 mm (W) x 142.7 mm (L) Weight 843 g Voltage:+24 VDC (11-30 VDC) Ratings Current: 300 mA max Power: 8W Environmental Operating Operating Conditions: 0ºC to 50ºC... -
Page 6: Installation
Installation Install your DSMax sensor head by performing the following steps: Mount the DSMax sensor head using three socket head cap screws: Screw height: 70mm Screw thread: M4 Dimension A 82 mm* Dimension B 121 mm* Dimension C 26 mm* Hole Diameter 5.2 mm... - Page 7 Vertically position the sensor where objects to be scanned appear within the field of view (FOV). Specification Distance (mm) Near Field of View 30.2 Far Field of View 33.3 Clearance Distance 51.4 Measurement Range 10.9 Launch your VisionPro vision application and configure the sensor as an image source.
-
Page 8: Indicator Lights
Indicator Lights The DSMax sensor head supports indicator lights to represent that status of the laser and the CoaXPress transmission status: The Laser Indicator Light represents one of the two operating states: Color Operating State Power Provided to Laser Green... - Page 9 Show pulse orange Device / Host connected, waiting for event (e.g. trigger, exposure pulse) Fast flash green Device / Host connected, data being transferred 500ms red pulse in case of multiple errors. At least two Error during data transfer (e.g. CRC error, single bit green fast flash pulses before the next error is indicated error detected) Fast flash red...
-
Page 10: Laser Compliance
CLASS 2M LASER PRODUCT FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE SERIOUS INJURY Cognex Corporation places the following labels on every DSMax Sensor Head: Compliant with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. Certified to Class 2M according to IEC 60825-1:2007 and IEC 60825-1:2014-5. -
Page 11: Laser Safety Warnings
Do not view directly with optical instruments (magnifying or telescopic) or direct laser beam into an area where such instruments are likely to be used. Cognex recommends the usage of protective eyewear with specs equivalent to Newport Laser Safety Glasses (P/N: G30103). -
Page 12: Important Product Information
Important Product Information Under no circumstance should you modify the DSMAX Sensor Head in any way. There is no scheduled maintenance necessary to keep the product in compliance. When moving the unit from a warm environment to a cold environment, allow the unit to equalize in a room temperature environment for 24 hours. -
Page 13: Product Service
Rotate the tissue or swab during cleaning so dirt is not dragged across the surface If the DSMAX Sensor Head is soiled such that full liquid immersion is required, fasten TNC caps to I/O connectors and rinse the unit with appropriate cleaning fluid. Failure to fasten TNC caps before immersion will result in IRREPARABLE DAMAGE to the DSMAX Sensor Head. - Page 16 Copyright @2018 Cognex Corporation. All rights reserved. Printed in the USA Part Number: 4000000544...
Need help?
Do you have a question about the DSMax and is the answer not in the manual?
Questions and answers