Voxx Electronics PRESTIGE APSSECRS Quick Installation Manual page 2

APSSECRS
Security and Remote Start
Quick Installation Guide
For Complete Installation Guide and Technical Support
Please Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
REV. B 2020 Voxx Electronics. All Rights Reserved.
Notifications
Alarm
When the alarm is triggered the system will provide feedback to the user. Upon disarm,
the system will beep 4x and flash the LED to indicate the Alarm Trigger Zone.
1 Shock
2 Trunk / Hood
3 Door
Remote Start
If the remote start fails to start the vehicle, the system will flash the vehicle parking
lights to indicate the cause.
1 Run�me Expired
2 Remote Shutdown
3 Brake On
4 Manual Mode
5 Hood Open
6 Low / No Tach
7 Tach Programming
8 High Tach
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature
Bank programming.
1. Turn the ignition key ON/OFF.
2. Press and release the valet button three (3) times.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This
feature will not affect alarm trigger or programming.
User Programmable LED
System LED notifications can be turned ON or OFF without entering Feature Bank
programming.
1. Turn the ignition key ON/OFF, ON/OFF.
2. Press and hold valet button for five (5) seconds.
The LED will flash one (1) time for ON, two (2) times for OFF. This feature will not affect
LED flash during programming.
Remote Programming
The APSSECRS does not include an RF remote kit. The RF remote kit Includes two (2)
remotes, one (1) antenna, and one (1) cable. When added, remotes must be programmed
to the system. Remote Programming is located in Feature Bank 1. To enter Remote Auto
Programming:
1. Turn the ignition key to ON.
2. Press and release the valet button three (3) times. System will beep and flash the
parking lights one (1) time.
Press the lock button on each remote. The system will beep one (1) time to indicate the
remote has been programmed. If programming one (1) button remotes, press the Start
button. Only primary remote functions are auto programmed. This Includes Lock, Unlock,
and Trunk/Start.
If using AUX output control, you must manually program the AUX output channels to
the remote. Please see the complete installation guide for manual remote programming
instruction.
Note: If programming 2-Way remotes, wait for the remote to beep before programming
additional remotes. This beep is confirmation that a 2-Way response has been received
from the main module.
Feature Programming
The APSSECRS Feature Banks can be programmed by using the valet button and remote.
To enter Feature Bank programming:
1. Turn the ignition key to ON.
2. Press and release the valet button three (3) times. System will beep and flash lights
one (1) time for Feature Bank 1, Remote Programming.
3. Cycle ignition key OFF/ON. System will beep and flash lights two (2) times for
Feature Bank 2.
4. Press valet button to cycle features. LED will flash to display feature number.
5. Press lock button to cycle options. System will beep to indicate option number.
6. Cycle ignition key OFF/ON. System will beep and flash lights three (3) times for
Feature Bank 3.
7. Press valet button to cycle features. LED will flash to display feature number.
8. Press lock to cycle options. System will beep to indicate option Number.
Tach Programming
The installer must manually configure the Engine Confirmation method in Feature Bank
3, Feature 5. The default method is "Tach". When using the default "Tach" method, the
vehicle tach rate must be programmed. To enter tach rate programming:
1. Turn the ignition key ON.
2. Press and release the valet button three (3) times.
3. Turn the ignition key OFF.
4. Press and hold valet button.
5. While holding valet button, start the engine using the key.
6. Hold the valet button for approximately ten (10) seconds. If connected to the vehicle
Tach source, the system will flash the parking lights one (1) time every second.
7. Release the valet button. The system will turn on the parking lights for two (2)
seconds to indicate the tach rate is programmed.
The tach rate can also be programmed without the use of a valet button. This is helpful
when using the OEM remote of CarLink system to control this module. To program the tach
rate without a valet button:
1. Turn the ignition key to the ON position and start the vehicle's engine.
2. Wait for Engine RPM to lower to a normal idle.
3. Press and hold the vehicle's brake pedal.
4. Press the LOCK button on the OEM remote or the Carlink App.
Note: Programming tach signal via OEM or Telematics control is only available on Firmware
v1.47 or Higher.
Data Protocol Selection
The default data port protocol of this model is ADS (iDatalink 2-Way). This model is capable
of detecting the correct data port protocol (ADS or DBI) and automatically configuring
Feature Bank 2; Feature 18. To initialize the detection procedure:
1. Press and hold the valet button.
2. Cycle the vehicle's Ignition ON/OFF two (2) times.
3. Release the valet button.
The system will automatically detect and set the correct data port protocol, ADS or DBI.
Note: This feature is only available on module firmware v2.0 or higher.
The Feature Banks below can also be programmed using the FlashLogic Weblink or Weblink Mobile.
Feature Bank 2
1 Chirp 2 Chirp
1 Lock / Unlock Func�on 500ms 3.5sec
2 Igni�on Lock OFF ON
3 Igni�on Unlock OFF Unlock All
OFF
4 Exterior Illumina�on With Arm
5 Auto Relock OFF Auto Lock Only
6 Auto Arming / Locking OFF Auto Arm Only
7 No�fica�on Sound Both Siren
8 Horn Timing 16ms 30ms
9 Valet Override Method Valet Custom Code
10 Driver Priority Unlock OFF ON
OFF
11 Silent Choice From Transmi�er
12 Security Profile All On Doors off
13 Door Trigger Input Negative Posi�ve
14 Park Light / Trunk Swap OFF ON
15 Data Port Protocol ADS DBI
16 Dome Light Delay Timer OFF / Program 15sec
17 Alarm Trigger Legnth 30sec 45sec
Feature Bank 3
1 Chirp 2 Chirp
1 Defrost Output Pulsed 10min
2 RS Start No�fica�on ON OFF
3 RS Run�me 15min 20min
4 RS Parking Lights Steady Flashing
5 Engine Confirma�on Tach Voltage
>0.5v B4 Start
6 Voltage Level <0.5v B4 Start
7 Igni�on 2 Output Ignition Accessory
8 Igni�on 3 Output Ignition Accessory
9 Accessory Output Accessory Igni�on
10 Transmission Auto Manual
11 Max Crank Time 0.8sec 1.0sec
12 Diesel Delay OFF Diesel 5
OFF
13 Temperature Start 14F
14 Crank Dura�on Averaging Preset
15 RS Shock Override Shunt until Clear Shunt RS Cycle
16 Turbo Timer OFF 3min
17 Start Ac�va�on Two Press One Press
18 RS Lock Func�on No Change UL Before L A�er
19 Factory Disarm Output Single Pulse Double Pulse
20 Addi�onal Unlock Pulse No Pulse IGN, ACC, GWR
Dome Delay Programming
This system can be programmed to ignore the vehicle's theater dimming dome light. This
feature will be used when connecting the door trigger input to the dome light circuit for
alarm trigger.
Start with all doors closed and the vehicle dome light off.
1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light solid.
2. Open and close the driver door.
The system will monitor the dome light circuit. When the dome light turns off the system
will set the delay time and add an additional two (2) seconds.
Dome Delay Reset
1. Key ON/OFF, ON/OFF, ON/OFF.
2. Press and hold valet button for five (5) seconds.
The system will beep one (1) time to indicate reset is complete.
Programmable Input Control
Programmable Input Control allows any PIC be configured to one of the options listed
below. This feature is accessible via FlashLogic Weblink or Weblink Mobile.
Door Trigger Full Shock Trigger
Trunk Trigger Parking Brake
Hood Trigger Brake
N.C. Door Trigger External Start Ac�va�on
Pre-Warn Shock Trigger Diesel Glow Plug
Op�ons
3 Chirp 4 Chirp 5 Chirp
500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL
Unlock Driver
With Disarm With Arm & Disarm
Auto Lock & Arm
Auto Lock & Arm
Horn
40ms 50ms 10ms
Stand Alone Valet
OEM Style
Hood / trunk Off All Off All On w/ OEM RS
30sec 45sec 60sec
60sec 90sec 120sec
Op�ons
3 Chirp 4 chirp 5 Chirp
RS Run�me
45min 60min 5min
Data Hybrid
Start
Start
Start
1.5sec 2.0sec 3.0sec
Diesel 10 Diesel 15 Diesel 20
5F 0F -4F
Shunt From TX
5min 10min
Three Press
UL Before Start Lock A�er Start
350ms 500ms 800ms
IGN,ACC,GWR,PASD
Negative Output Control (NOC)
Negative output control allows any NOC to be programmed for any one of the options
below. This feature is accessible via FlashLogic Weblink or Weblink Mobile.
Lock Ground While Armed
Unlock Ground While Disarmed
2nd Unlock Domelight
Trunk Headlight
Remote Start Status Defrost
Igni�on LED
Accessory Ch. 4 AUX
Pulse During Crank Ch. 5 AUX
Pulse A�er Shutdown Ch. 6 AUX
Factory Arm Ch. 7 AUX
Factory Disarm
AUX Output Control
Any AUX output can be configured using the AUX Control Menu. This feature is only
accessible via FlashLogic Weblink or Weblink Mobile.
1 Second Pulse 30 Second Pulse
5 Second Pulse Push & Hold
10 Second Pulse Latch ON/OFF
15 Second Pulse Latch 10min w/ RS
20 Second Pulse Latch Run�me
6 Chirp
500ms L, 350ms UL
120sec
6 Chirp
10min
4.0sec
Diesel 30
-14F
Same As Bank 2, F1