First Time Installation - Walker WPS818C SAORVIEW Operating Instructions Manual

Some stream packets may not be recorded because
of signal problems, as a result sometimes videos may
freeze during playback.
Record, Play, Pause, Display (for PlayListDialog) keys
can not be used when teletext is on. If a recording
starts from timer when teletext is on, teletext is
automatically turned off. Also teletext usage is
disabled when there is an ongoing recording or
playback.
If "USB disk writing speed too slow to record" message
is displayed on the screen while starting a recording,
try restarting the recording. If you still get the same
error, it is possible that your USB disk does not meet
the speed requirements. Try connecting another
USB disk.
For more information on recording programmes, see
Instant Recording, Timeshift Recording, Watching
Recorded Programmes and Recording Settings
sections on the following pages.

First Time Installation

When turned on for the first time, the language
selection screen is displayed. Select the desired
language and press OK.
On the next screen, set your preferences using the
directional buttons.
Note: Depending on the Country selection you may be asked
to set and con rm a IN at this point. he selected IN cannot
be 0000. You have to enter it if you are asked to enter a PIN
for any menu operation later.
About Selecting Broadcast Type
Terrestrial Search: If Terrestrial Search broadcast
search option is turned on, the box will search for
digital terrestrial broadcasts after other initial settings
are completed.
Satellite: If Satellite broadcast search option is turned
on, the box will search for digital satellite broadcasts
after other initial settings are completed.
Press OK button to continue. Privacy Settings menu
wil be displayed at this point. Using this menu you can
set your privacy privileges. Highlight a feature and
use Left and Right directional buttons to enable or
disable. Read the related explanations displayed on
the screen for each highlighted feature before making
any changes. You can use Programme +/- buttons to
scroll up and down to read the entire text. You will be
able to change your preferences at any time later from
the Settings>Privacy Settings menu. If the Internet
Connection option is disabled Network/Internet
Settings screen will be skipped and not displayed.
If you have any questions, complaints or comments
regarding this privacy policy or its enforcement, please
contact by email at smarttvsecurity@vosshub.com.
Press OK button on the remote control to continue
and the Network/Internet Settings menu will be
displayed, if you confirm the previously displayed
message asking whether you want to do the network
settings. Please refer to Connectivity section to
configure a network connection. After the settings
are completed press OK button to continue. To skip
to the next step without doing anything select No and
press the OK button when the message is displayed
asking whether you want to do the network settings.
After the initial settings are completed set-top box will
start to search for available broadcasts.
Before satellite search is performed some settings
should be made. Antenna Type menu will be
displayed first. You can select Antenna Type as
Direct, Single Satellite Cable or DiSEqC switch by
using Left or Right directional buttons.
Direct: If you have a single receiver and a direct
satellite dish, select this antenna type. Press OK to
continue. Select an available satellite on the next
screen and press OK to scan for services.
Single Satellite Cable: If you have multiple
receivers and a single satellite cable system, select
this antenna type. Press OK to continue. Configure
settings by following instructions on the next screen.
Press OK to scan for services.
DiSEqC switch: If you have multiple satellite dishes
and a DiSEqC switch, select this antenna type.
Press OK to continue. You can set four DiSEqC
options (if available) on the next screen. Press OK
button to scan the first satellite in the list.
A dialogue will appear next asking whether you want
to load the preset list. If you select Yes and press
OK a warning message may appear, if a satellite
with preset list support is not selected. In this case
the preset list can not be loaded and a message will
be displayed. Press OK to return to satellite selection
screen and set a satellite with preset list support. If
the settings are made correctly the preset list will
be loaded. If you want to perform a normal satellite
scan select No and press OK when the dialogue is
displayed on the screen.
After all the available stations are stored, scan results
will be displayed. Press OK to continue. The Edit
Channel List menu will be displayed next. You can
edit the channel list according to your preferences or
press the Menu button to quit.
While the search continues a message may appear,
asking whether you want to sort channels according
to the LCN(*). Select Yes and press OK to confirm.
(*) LCN is the Logical Channel Number system that organizes
available broadcasts in accordance with a recognizable
channel number sequence (if available).
Note: Do not turn off the bo while initializing rst time
installation. Note that, some options may not be available
depending on the country selection.
English - 9 -