3M 9000PD Operator's Manual
  1. Manuals
  2. Brands
  3. 3M Manuals
  4. Projector
  5. Digiral Walldisplay 9000PD
  6. Operator's manual
3M 9000PD Operator's Manual

3M 9000PD Operator's Manual

3m digital wall display operator's guide
Hide thumbs Also See for 9000PD:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Quick Reference Manual
Operator's Guide
...for projection
9000PD
February 2005
78-6970-9380-1 Rev. B
Copyright © 2004, 3M.
All Rights Reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9000PD and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for 3M 9000PD

Summary of Contents for 3M 9000PD

  • Page 1 Operator’s Guide …for projection 9000PD February 2005 78-6970-9380-1 Rev. B Copyright © 2004, 3M. All Rights Reserved.
  • Page 2 (This page intentionally left blank for printed version)

  • Page 3: Table Of Contents

    3M™ Digital WallDisplay Contents Introduction Thank You for Choosing 3M ...5 Safety Information ...5 Intended Use ...5 Product Safety Label ...9 Save These Instructions ...9 Trademarks ...9 Patents ...10 3M Digital WallDisplay Technical Support...10 FCC Statement—Class A ...10 EEC Statement—Class A ...10 Model Identification and Differences...11...
  • Page 4 Common Problems and Solutions ...41 Onscreen Messages...42 Service Information Replacement Parts ...43 Optional Accessories ...43 Ordering Parts or Getting Information ...43 Appendix 3M™ Digital WallDisplay Specifications ...44 Input/Output Signal Specifications...45 Computer Compatibility ...45 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved.

  • Page 5: Thank You For Choosing 3M

    Before operating this machine, please read the entire manual thoroughly. The 3M Digital WallDisplay Systems are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.
  • Page 6 • Do not attempt to service the Wall Display other than performing routine lamp replacement. Service should only be performed by a 3M authorized service provider. Aside from the projection lamp assembly, there are no serviceable parts inside the unit.
  • Page 7 To reduce the risks associated with impact from the projection arm and tripping over the legs of the portable cart: • Do not use this Wall Display around unsupervised children. • Do not allow children to hang onto the projection arm. © 3M 2005. All Rights Reserved.  WARNING  CAUTION Introduction...

  • Page 8: Important Notes

    • Do not manually open or close the projection arm while the 3M Digital Wall Display is in operation. • Save the shipping box and packing materials in the event the 3M Digital WallDisplay should ever need to be moved.

  • Page 9: Product Safety Label

    3M™ Digital WallDisplay Product Safety Label The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention. Wall Display Save These Instructions The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay.

  • Page 10: Patents

    Communications Corporation and may be registered outside the U.S. All other products are trademarks or registered trademarks of their respective companies. Patents 3M Digital WallDisplay is protected by Utility Patent 6,179,426 and Design Patent D442,205. Other patents pending. 3M Digital WallDisplay Technical Support •...

  • Page 11: Model Identification And Differences

    9200IW 9200IC *The Copyboard feature allows you to print notes written on the 3M Digital WallDisplay to an attached printer. (PCL3 compatible printer required. See list in Appendix.) **The Digital Whiteboard feature allows you to capture notes written on the 3M Digital WallDisplay with an attached computer or use the 3M Digital WallDisplay as an interactive display for a computer.

  • Page 12: Contents

    What’s Next? After the 3M Digital WallDisplay has been installed in your meeting room, you are ready to set it up. Please read this guide thoroughly before operating your new 3M Digital WallDisplay. Be sure to check our web site (www.3M.com/walldisplay) regularly for updates and supplemental information.

  • Page 13: Part Identification

    3M™ Digital WallDisplay Part Identification © 3M 2005. All Rights Reserved. Wall Display AUDIO VIDEO COMPUTER AUDIO MOUSE S-VIDEO 2 (THIS ROW FOR DIGITAL WHITEBOARD OPTION ONLY) PRINTER COMPUTER Introduction fro m 3 M SERIAL RS-232 DVI-D MOUSE MENU KEYPAD...

  • Page 14: 3M Digital Walldisplay Features

    Introduction 3M Digital WallDisplay Features The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package. • Full connectivity for computer or video presentations • Large 60˝ diagonal screen • 4:3 screen aspect ratio matches business applications and viewing data •...

  • Page 15: Installation And System Setup

    Recommendation and Things to Consider Before Installing Location of Unit • Place near AC outlet. The AC power connection is located on the lower-left corner of the 3M Digital WallDisplay (the unit). The AC power cord supplied with the unit is 6 feet (2 m) long.

  • Page 16: Installing The Wall Bracket

    Note: For other types of wall material (e.g. wood, concrete, concrete block) use mounting hardware that is properly rated for the weight of the unit and is intended for specific wall material. 3M™ Digital WallDisplay To Floor © 3M 2005. All Rights Reserved.

  • Page 17: Hanging The 3M Digital Walldisplay

    3. Remove the accessory box(es) from the top support. 4. Remove the top support. 5. Remove the plastic bag from the 3M Digital WallDisplay by lifting the top of the unit and pushing the bag towards the bottom of the unit.
  • Page 18 Installation and System Setup Hanging on the Wall 1. If possible, position the 3M Digital WallDisplay and shipping tray in front of the wall where the bracket is located. Position the unit so that the projection arm is closest to the wall.

  • Page 19: System Setup

    3M™ Digital WallDisplay System Setup It only takes a few minutes to connect the 3M Digital WallDisplay to your computer, VCR, DVD player, video conference unit, or other devices. The connection panel is located underneath the bottom right corner of the 3M Digital WallDisplay, under the Connection Panel Door.

  • Page 20: Operation

    2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the 3M label. This should stay on at all times. Now the 3M Digital WallDisplay is in standby mode. The large oval On/Off Button will be backlit amber after several seconds.

  • Page 21: Shutdown

    On/Off Button will flash red. The fan will continue to run for approximately five minutes to cool the unit. Note: If the 3M Digital WallDisplay will not be moved or disconnected, leave the Master Power Switch on for your convenience.

  • Page 22: Remote Control Unit

    Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover.

  • Page 23: Forward Keypad

    3M™ Digital WallDisplay Forward Keypad Power Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn off the sound. Press again or press the Volume + or - buttons to restore sound.

  • Page 24: Rear Keypad

    Trigger Button On the underside of the remote control unit, beneath the IR sensor, press button for left-mouse-button functions. 3M™ Digital WallDisplay POWER MOUSE MENU MUTE BLANK INPUT POINTER VOLUME FREEZE REVEAL TIMER © 3M 2005. All Rights Reserved.

  • Page 25: Installing Or Replacing Batteries

    2. Install two AAA batteries as indicated by the diagram inside the compartment. 3. Snap the battery compartment cover back on. Note: Avoid excessive heat and humidity. Do not mix old and new batteries or different types of batteries. © 3M 2005. All Rights Reserved. Remote Control Unit...

  • Page 26: Menu System

    Menu Navigation Most adjustments and settings are available in the main menu and sub-menus. To navigate and make adjustments, use the 3M Digital WallDisplay’s Menu Keypad button or the remote control’s Menu and Disk Pad buttons. Colorful—Bright Slider The Colorful—Bright slider adjusts the brightness, contrast, and color saturation levels simultaneously. Move the slider toward Colorful to achieve maximum color saturation and contrast.

  • Page 27: Warm-Cool Slider

    3. Move the slider by pressing the left or right arrow of the Disk Pad or Menu Keypad. 4. Close the menu system by pressing the Menu button or scrolling to Exit and selecting it with the right arrow of the Menu Keypad. © 3M 2005. All Rights Reserved. Menu System...

  • Page 28: Mute Menu Function

    4. Close the menu system by pressing the Menu button or scrolling to Exit and selecting it with the right arrow of the Menu Keypad. Mute function ON Mute function OFF © 3M 2005. All Rights Reserved. 3M™ Digital WallDisplay...

  • Page 29: Input Select Menu

    The Input options are: Computer (VGA Input), DVI-D, S-Video, Comp. Video (RCA Video Input), and No Signal. An Input option is available to select when an active video source is connected to the 3M Digital WallDisplay input connection. To set the Input Select menu: 1.

  • Page 30: Image Adj Sub-Menu

    5. Close the menu system by pressing the Menu button or scrolling to Exit and selecting it with the left or right arrow of the Menu Keypad. To return to the main menu, select Main and press the left or right arrow of the Disk Pad or Menu Keypad. 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved.

  • Page 31: Tools Sub-Menu

    Selects which language to use for onscreen commands. (Default language is English.) It cycles between English, German, Spanish, Italian, and French. Auto Shutoff Will automatically turn off the 3M Digital WallDisplay within the time desired. (Default time is 0 minutes.) Auto Switch When an input source is lost or disconnected, Auto Switch automatically detects and switches to the next available input source.

  • Page 32: Maintenance

    Maintenance General Maintenance For general cleaning of the screen and exterior of the 3M Digital WallDisplay, use a damp cloth or dry cleaning cloth such as the 3M High Performance Cleaning Cloth. Standard dry-erase cleaners may be used on the dry-eraseable screens, such as Sanford...

  • Page 33: Lamp Replacement

    5. Two black wires connect to the lamp cartridge by a black plastic receptacle on the right side of the lamp cartridge. © 3M 2005. All Rights Reserved. Maintenance Facade Lamp...
  • Page 34 8. Holding the latch open, slide the new lamp cartridge into place. 9. Reconnect black wires to the receptacle. 10. Close the lamp housing door and tighten the screw. 3M™ Digital WallDisplay Lever © 3M 2005. All Rights Reserved.
  • Page 35 Note: You must hear or feel a distinctive snap to ensure facade is securely attached. Whenever the lamp is replaced, please reset the total lamp operating time. (Refer to next page.) © 3M 2005. All Rights Reserved. Maintenance...

  • Page 36: Resetting Lamp Hours

    For disposal information in the US, contact the Electronic Industries Alliance at www.lamprecycle.org. In Canada contact the Electronic Product Stewardship Canada at www.wpsc.ca. 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved.

  • Page 37: Replacing Projectionscreen

    Replacing the 3M Digital WallDisplay screen is very simple. 1. Turn off the 3M Digital WallDisplay and disconnect the power cord from the wall outlet. 2. Remove the right and left side bezels. There are two ways to remove it. Either snap it off or insert a screwdriver into the notch located on the sides of each bezel, near the top.

  • Page 38: Optical Engine Adjustment

    3. Locate adjustment screw for side to side screen adjustment. Locate locking screw for side to side adjustment. 3M™ Digital WallDisplay ������������ ������������ ������� ����� ���������� ����� ���� © 3M 2005. All Rights Reserved.
  • Page 39 Locate locking screw for right side adjustment. 6. Loosen locking screw. Then use blade screwdriver on adjustment screw to move right side screen image up and down if required. Tighten locking screw. © 3M 2005. All Rights Reserved. Maintenance ���������� ���������� ���������� ����� ������� �����...
  • Page 40 Note: After making adjustments it may be necessary to perform the side to side adjustment to center the image properly. 9. Replace the optical adjustment door. 3M™ Digital WallDisplay ��������� ��������� ������� ����� ���������� ����� ���� © 3M 2005. All Rights Reserved.

  • Page 41: Troubleshooting

    The projection arm opens, then closes. Sound is heard with no picture. Picture is displayed with no sound Picture is dark. © 3M 2005. All Rights Reserved. Cause The power cord is disconnected. The Master Power Switch is not turned on.

  • Page 42: Onscreen Messages

    The menu system will not display without an input source displayed. Meaning 3M Digital WallDisplay is not receiving a signal from an external source. Check the cable connections and verify power is on and external source is working. The lamp has 1400–1499 hours on it and needs to be changed.

  • Page 43: Service Information

    The contents of this manual are subject to change without prior notice. 3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.

  • Page 44: M™ Digital Walldisplay Specifications

    Digital RGB: DVD-D (digital only) Audio: 3.5 mm stereo mini-jack S-Video: Mini DIN 4-pin RCA jacks 9-pin D-Sub 9-pin D-Sub 20 Watts per channel 40 Watts Max., 8 ohms 100~240 VAC, 50/60 Hz, 400 Watts Max. © 3M 2005. All Rights Reserved.

  • Page 45: Input/Output Signal Specifications

    Input/Output Signal Specifications Computer Video Computer Compatibility Resolution Refresh Rate 640x400 800x600 1024x768 1280x1024 © 3M 2005. All Rights Reserved. Video Signal Horizontal Sync Signal Vertical Sync Signal Audio Input Signal Audio Output Signal Luminance Signal S-Video Chrominance Signal Video Signal...
  • Page 46 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.

Table of Contents