W E L C O M E T O T H E E N V O FA M I LY Thank you for choosing an ENVO Electric Bike. As a leader in electric bike design and distribution in Canada, we are passionate about our customers riding their bikes more and driving their cars less.
If you have an impairment or disability such as visual impairment, hearing impairment, physical impairment, cognitive impairment, and/or a seizure disorder, consult your physician before riding any ENVO Drive Systems product • Before going on your first ebike adventure, take time to get familiar with your ebike •...
Always be gentle when pulling the charging pin out. Rough use of the pins can cause irreversible damage to the pins and battery • Do not use any other chargers to charge the ENVO battery other than ones provided by ENVO for the specific product you purchased •...
Do not use the ENVO battery charger for any purpose other than charging your ebike. Do not use the ENVO battery as a power source for any other devices than your ENVO ebike. If you do so the warranty will not be applicable, and ENVO Drive Systems will not be liable for any damage to the system or injury to the persons.
2 . 5 . B AT T E R Y R E M O VA L & I N S TA L L AT I O N The battery is located inside the seat post stem and can be removed if you wish to charge your battery separately.
70% of its capacity for about 500 full discharge/recharge cycles. As capacity diminishes, you will notice a gradual drop off in max range capability. When range falls to an unacceptable level, contact your local ENVO dealer to purchase a new battery.
Please make sure you are gentle when inserting or removing the charging cable from the charging port. Failure to do so can result in damaged pins and poor connections. 2 . 7 . B AT T E R Y T R A N S P O R T •...
2 . 1 0 . G E N E R A L R I D I N G T I P S Read, understand, and follow all of the instructions and safety precautions in this manual. Electric Bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property, arising out of or as a result of using the bicycle.
Page 12
• Do not operate if you are sleepy, sedated or while under the influence of drugs and/or alcohol • If motor speed is noticeably dropping while climbing a hill, assist the motor by pedaling • Do not pedal around a corner as you may gain to much speed and lose control •...
2 .11. 2 . W E I G H T C A PA C I T Y • The ENVO Lynx-20 is designed with a maximum weight capacity of 120 kg or 265 lbs. The rear rack maximum weight capacity of a is 20 kg or 44 lbs. Exceeding the maximum weight capacity can result in damage to the bike, which can lead to serious injury or death 2 .11.
3. PRODUCT DESCRIPTION 3 . 1 C O M P O N E N T S Saddle Folding Pedal Reflector Downtube Seat Post (Battery) Front Wheel Rear Rack Front Disc Brake Tail Light Front Fork Seat Post Clamp Front Rack Rear Wheel Headlight Rear Disc Brake...
3 . 2 . S P E C I F I C AT I O N S Model: ENVO Lynx-20 Folding eBike Wheel Base: 1067mm Size: 1680×590×1120mm Battery Capacity: 460Wh Folded Size: 930 × 480 × 700mm Ride System: 5 level PAS + Throttle...
500W with a 60 N m max torque making hills virtually effortless • The stylish and removable, A-grade lithium ion battery pack is the key feature of ENVO Lynx-20. Although the battery is hidden in the seat post making the design clean and minimal, it is easily accessible for replacement, transport and repairs.
It is highly recommended to get help from an experienced mechanic, refer to your local ENVO dealer (a list of ENVO dealers can be found on our website). If you choose to do it yourself, please make sure you refer to the online guides on envodrive.com for your own safety.
While cutting zip ties be careful not to scratch or damage your bike, be extra cautious while cutting zip ties around wire connections and cable housings. The battery is mounted on the bike frame. Do not damage the battery when removing it the frame from the box. 4 .
Never adjust the seat height beyond the maximum sign on seat post Figure 4D 4 . 4 . 2 . F O L D I N G • While holding the seat post, loosen the clamp. Slowly push the seat post all the way down and tighten the clamp to secure in place Figure 4D •...
4 . 5 . F E N D E R & R A C K M O U N T I N G • The fenders are unattached and located in the box • The rear rack is located on the bike Note: Allen Key Set is required 4 .
4 . 5 . 2 . R A C K S Front Rack • Max payload 22 lb / 10 kg • Front rack is secured onto the front of the head tube headtube with 2 screws • Make sure the screws are securely fastened and the rack is not loose Rear Rack •...
4 . 6 . P E D A L I N S TA L L AT I O N • Take the pedals out of the small box • Apply a small amount of grease to the screw portion of the pedal Figure 4N •...
5. OPERATING YOUR PRODUCT 5 . 1 . O P E R AT I O N 1. Press and hold the power button for 1 seconds to turn on your ebike (do the same to turn off). Data on screen: single riding distance, PAS (pedal assist system) class, single-speed range. 2.
Page 24
Pedal Assist Mode will be operative if the assist level is 1 or higher • ENVO ebikes are equipped with a Pedal Assist Sensor, which is installed on the bottom bracket, and senses pedal crank rotation electronically •...
5 . 5 . H A N D T H R OT T L E C O N T R O L • The ENVO Lynx-20 is equipped with a thumb throttle, which is located on the right side of the handlebar •...
• ENVO ebike brakes are equipped with microswitches which cut-off the motor power whenever either of the brake levers are squeezed. Please check the operation of your brake disconnect switch before every ride. While riding slowly in a controlled environment (like your driveway), engage the motor then squeeze each brake separately.
• To bed-in brakes simply roll down a hill or pedal to about 15 km/h and apply brakes until the ebike slows down and repeat about 15 times per lever. DO NOT let the bike come to a complete stop or let the wheels lock up •...
5 . 9 . R I D I N G Y O U R E B I K E I N R A I N O R S N O W • The ENVO Lynx-20 LCD system is rain proof and is safe to use in wet or snowy weather; however, power washing your ebike or parking/storing it in rain or snow will result in water penetrating the electronic components and cause damage •...
6. ACCESSORIES 6 . 1 . PA N N I E R S • To effectively balance the weight on your bike, it is recommended that you use 2 panniers. This ensures weight is evenly distributed on both sides of the bike •...
7. MAINTENANCE & REPAIR 7 . 1 . M A I N TA I N I N G PA R T S • Electric bikes like normal bikes need regular maintenance. The drivetrain needs cleaning and lubrication, the brake pads need to be changed periodically, and levers need to be bled if hydraulic or cables are changed •...
5. Realign the components if necessary and carefully tighten the bolts to ensure reliable clamping of the components. The maximum torque values are printed directly on the components and/or specified in the enclosed operating instructions. If neither are available, contact ENVO support for assistance 6.
Page 32
16. At no time should you make any modifications to your ebikes electrical systems, unless they are explicitly approved by the manufacturer in writing 17. Contact your dealer or ENVO support for repairs and replacement parts in case of damage EN VO LYN X-20 FO LDIN G EB IKE M ANUAL...
7 . 4 . Q U I C K T R O U B L E S H O OT I N G If your ENVO ebike is not working, check the Quick Disconnect Fittings to make sure it did not come loose, unplugged or have any wear and tear.
7 . 4 . T R O U B L E S H O OT I N G TA B L E C O MP ONENT ISS U E C AUS E S OLU T IO N Charger Charger gets hot This is normal Give the charger plenty of space in a well ventilated...
Page 35
Check arrows alignment be stretched then push the connector back in firmly Motor cable is scratched or Contact ENVO support torn Water penetrated inside the Dry motor by putting it in motor casing a hot and dry place for 48...
Page 36
For any additional troubleshooting help, refer to support.envodrive.com or contact your local ENVO Electric Bike dealer. EN VO LYN X-20 FO LDIN G EB IKE M ANUAL V ER S ION 1 .1...
8. TRANSPORTATION & STORAGE 8 . 1 . T R A N S P O R TAT I O N • Please be careful when loading your ebike onto a vehicle rack • Be aware of battery cables and other wires when loading and unloading •...
I M P O R TA N T N O T E : You must register your electric bike with ENVO Drive Systems within 30 days of purchase for warranty to be valid. EN VO LYN X-20 FO LDIN G EB IKE M ANUAL...
• In case the issue is not diagnosed by standard ways; for our hub motor kits, ENVO ebikes, and other house brand products, since the electrical system is modular and has easy access. We would be able to easily send you replacement parts such as a controller to swap and test and return the defective one.
CONTACT L O C AT I O N ENVO Drive Systems Inc. 1685 Ingleton Avenue Burnaby, BC V5C 3V6 Canada B U S I N E S S H O U R S Monday – Friday: 10am – 5pm PST Saturday: 11am –...
Need help?
Do you have a question about the LYNX-20 and is the answer not in the manual?
Questions and answers