Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Impresind UVL100
Summary of Contents for Impresind UVL100
- Page 1 Air Sanitizer and Mixer Manual for Installation, Use and Maintenance...
-
Page 2: Table Of Contents
6.3 Putting the appliance “at rest” ....................12 7 - Maintenance ......................... 13 8 - Disposal ..........................14 8.1 Decommissioning ........................14 IMPRESIND SRL Production site: Via Primo Maggio 24, Gorgonzola (Milan) - ITALY ℡ +39 02 95741932 +39 02 73960191 ... -
Page 3: Eliturbo Uv-Light - Product Introduction
® ELITURBO UV-LIGHT - Product Introduction ® ELITURBO UV-LIGHT is designed to perform the double function of air sanitizer and air mixer. The sanitization process involves a germicidal activity for the reduction of bacterial and viral loads in the air. Sanitization takes place in a special chamber where ultraviolet light (UV-C) lamps are housed and where the contaminated air taken from the environment goes through. -
Page 4: General Information
Eliturbo UV-LIGHT produced by Impresind s.r.l. The measurements were performed at the Impresind by the FRIEST company with the certified instrumentation JETI GMBH & Delta Ohm, of their mobile laboratory, standardized with the USL legislation. - Page 5 WARNING: The installation position of the Eliturbo UV-LIGHT must ensure that the distance from the people staying in the room are respected as indicated in the image below, in any case at height of not less than 2,5 m from the ground. SAFETY WARNING: •...
-
Page 6: Receiving The Equipment
1.3 Storing - During transport and storage the temperature must be between -10°C and +50°C. -
Page 7: Product Specifications
2 - Product Specifications 2.1 Technical specifications MODEL CODE UVL100 Technical data Absorbed power Power supply 220-240 Frequency 50 / 60 Fan type axial Airflow Sound Level (Lp) db(A) Ingress Protection level Dimensions Diameter Height Weight Surface treatment powder coating... -
Page 8: Installation
3 - Installation 3.1 General instructions for the installation Before the installation, the qualified and trained personnel must read this manual and wear personal protective equipment (PPE) such as safety glasses (scale number 2, 2C or 3 according EN166), gloves, etc… Before proceeding with the installation, make sure that all the components are unpacked and not damaged. -
Page 9: Connection To Power Supply Network
3.3 Connection to power supply network The connection to power supply network must be carried out by qualified and trained personnel, after reading this Installation, Use and Maintenance Manual. Before carrying out the power supply and/or control connections it always necessary to check that the power supply is disconnected. -
Page 10: Operation Checks
3.4 Operation checks Before switching-on the appliance, make sure that all the staff involved have been properly informed about risks and dangers of the appliance itself, as reported in the present manual. Before switching-on the appliance, check that all the supporting elements (chains, cables, etc.) are firmly fixed, that the appliance is perfectly horizontal, that the power supply cables do not interfere with any object and that the appliance is properly powered. -
Page 11: Residual Risks
IMPRESIND’s Technical Dept. IT IS ABSOLUTELY FORBIDDEN TO USE WATER TO EXTINGUISH FIRES IST STP101.147 GB-23-12-20... -
Page 12: Use
6 - Use 6.1 Switching on / Switching off Switch on and off of the appliance is carried out by using the appropriate devices set up during the installation phase: eg. omnipolar switch and/or timer. 6.2 Recommendations to Users In order to better counteract the natural proliferation of microorganisms, EITURBO UV-LIGHT® must work continuously. -
Page 13: Maintenance
7 - Maintenance ATTENTION : All maintenance operations must be carried out exclusively by qualified and informed personnel. WARNING : before proceeding with any ordinary and extraordinary maintenance operation, check that the appliance is not electrically powered. Check the proper functioning of the appliance yearly, so that it is possible to carry out any needed maintenance and/or repair in due time. -
Page 14: Disposal
8 - Disposal 8.1 Decommissioning Disposal of the appliance must be carried out by specialized personnel provided with suitable tools and Personal Protection Equipment (PPE). INFORMATION ABOUT END OF LIFE DISPOSAL Attention: This product is within the scope of Directive 2012/19 / EU concerning the management of waste electrical and electronic equipment (WEEE). - Page 15 IST STP101.147 GB-23-12-20...
-
Page 16: Impresind Srl
IMPRESIND SRL Via Primo Maggio 24, 20064 Gorgonzola (Milano) ITALY ℡ +39 02 9574.1932 +39 02 7396.0191 info@impresind.com www.impresind.com IST STP101.147 GB-23-12-20...