Related Manuals for Flotrol F60
Summary of Contents for Flotrol F60
- Page 1 F60 Downflow Brining Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference.
-
Page 3: Job Specification Sheet
MODEL F60 Job Specification Sheet Job No. Model No. Water Test Capacity Per Unit Mineral Tank Size . DiaMeter Height Brine Tank Size & Salt Setting per Regeneration: Control Valve Specifications 1. Type of Timer (see pages 8-11) A) 7 Day or 12 Day... -
Page 4: General Commercial Pre-Installation Check List
MODEL F60 General Commercial Pre-Installation Check List WATER PRESSURE: A minimum of 25 pounds of water pressure is required for regeneration valve to operate effectively. ELECTRICAL FACILITIES: A continuous 115 volt, 60 Hertz current supply is required. (Other voltages avaiIable. ) Make certain the current supply is always hot and cannot be turned off with another switch. -
Page 5: Timer Setting Procedure
MODEL F60 Timer Setting Procedure Service How To Set Days On Which Water Conditioner Is To Manual 24 HR. Gear Position Regeneration Regenerate: Indicator Knob Rotate the skipper wheel until the number “1” is at the red TO SET TIME OF DAY- pointer. - Page 6 MODEL F60 Regeneration Cycle Program Setting Procedure Conditioner will rapid rinse (2 min. per pin). How To Set Regeneration Cycle Program: To change the length of rapid rinse time, add or The regeneration cycle program on your water condi- remove pins at the higher numbered end of this section tioner has been factory preset, however, portions of the as required.
- Page 7 MODEL F60 Commercial Demand Regeneration Control Timer Settings Typical Programming Procedure 5. In any event, conditioned water may be drawn after rinse water stops flowing from the water condi- Calculate the gallon capacity of the system, subtract the necessary reserve requirement and set the gallons tioner drain Iine.
- Page 8 MODEL F60 Timer Assembly (For Mechanical Clock) Page 8...
- Page 9 MODEL F60 Timer Assembly (For Mechanical Clock) Item No. Quantity Part No. Description 051-00078-00 Timer Housing 069-00180-00 Decal- Instructions 051-00074-00 Cycle Actuator Arm 099-00177-00 24 Hour Gear Assembly 051-00089-00 Knob 066-00002-00 Screw,tchw,NO.6-20x1/2,b,black,Zn,1022 069-00179-00 Button Decal 099-00176-00 Skipper Wheel Assembly 078-00008-00...
- Page 10 MODEL F60 Timer Assembly (For Mechanical Meter) 10 11 Page 10...
- Page 11 MODEL F60 Timer Assembly (For Mechanical Meter) Item No. Quantity Part No. Description 051-00078-00 Timer Housing 069-00188-00 Decal- Instructions2 057-00011-00 Cycle Actuator Gear- SM 051-00089-00 Knob 066-00002-00 Screw,tchw,NO.6-20x1/2,b,black,Zn,1022 069-00179-00 Button Decal 069-00186-00 Gallons Label 066-00008-00 Screw-PSWA 057-00012-00 Progran Skipper Wheel...
- Page 12 MODEL F60 Assembly Drawings and Part Numbers F60 Control Valve Assembly LARG E BRINE SYSTEM ASSEMBLY FILTER PARTS NRWB PISTON ASSEMBLY BLOCK-A BLOCK-B RW B PISTON ASSEMBLY BLOCK-C B LO C K -B Page 12...
- Page 13 MODEL F60 Assembly Drawings and Part Numbers F60 Control Valve Assembly Parts List Item No. Quantity Part No. Description 066-00028-00 Screw M12*35 052-00279-00 FT Valve Body (NPT) 052-00060-00 FT Valve Body (BSP) 060-00042-00 Valve-Tank Adapter Seal 060-00083-00 O-Ring-229 (US) 060-00043-00...
- Page 14 MODEL F60 Control Drive Assembly (For 60 Mechanical) 24 23 26 25 FOR SM 18 19 20-1 20-2 14 15 Page 14...
- Page 15 099-00750-00...
- Page 16 MODEL F60 Assembly Drawings and Part Numbers F60 Control Valve Assembly Page 16...
- Page 17 MODEL F60 Assembly Drawings and Part Numbers Large Brining System Assembly Parts List Item No. Quantity Part No. Description 052-00081-00 Stem Guide Assembly 068-00011-00 Retaining Ring 058-00006-00 Spring 066-00005-00 Screw 052-00280-00 Brine Valve Body (NPT) 052-00064-00 Brine Valve Body (BSP)
- Page 18 MODEL F60 Assembly Drawings and Part Numbers 2" Flow Meter Assembly & Parts List MECHANICAL METER COVER ASS'Y ELECTRONIC METER COVER ASS'Y Item No. Quantity Part No. Description 052-00086-00 Impeller Shaft Retainer 051-00195-00 Impeller 052-00085-00 Impeller Shaft 060-00026-00 O-Ring 099-00734-00...
- Page 20 MODEL F60 F60 Downflow Service Instructions PROBL EM CAUSE CORRECTION 7. Excessive water in brine tank Plugged drain line flow control. Check flow control. Clean injector and screen. Plugged injector system. Timer not cycling. Replace timer. D. Replace brine valve seat and clean valve.
-
Page 21: Dimensional Drawing
MODEL F60 Dimensional Drawing 179mm (7.0") 410mm (16.2") 1" 2" 225mm (8.8") 207mm (8.2") Assembly Drawings and Part Numbers Page 21... - Page 22 099-01670-00 #8 Injector Assembly 100-00017-00 Piston Kits-NRWB 099-01671-00 #10 Injector Assembly Seals & Spacers Large 1” Brine Valve 100-00044-00 F60 Spacers & Seals 100-00058-00 Brine Valve Assembly Meter(2" Electronic Flow Meter) Meter(2" Extended Mechanical Flow Meter) 100-00038-00 99.5" Cable 100-00042-00 100-00041-00 300"...
- Page 23 MODEL F60 Notes Page 23...
- Page 24 AAHK076-00006-00V1.0...