Advertisement
Quick Links
Form No. 3365-747 Rev A
Vinyl Enclosure #07337
FOR
Toro Workman MD series only
PARTS LIST – ASSEMBLY INSTRUCTIONS
IMPORTANT
READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE
CAUTION !
REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER
WARNING !
THIS CAB WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY COLLISION, OR OTHER
ACCIDENTS
1
60276109
Advertisement
Related Manuals for Toro 07337
Summary of Contents for Toro 07337
- Page 1 Form No. 3365-747 Rev A Vinyl Enclosure #07337 Toro Workman MD series only PARTS LIST – ASSEMBLY INSTRUCTIONS IMPORTANT READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE CAUTION ! REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER...
- Page 2 WARNING 1. This cab is designed to provide foul weather protection only. It does not provide protection from noise, exhaust fumes, chemicals or injury from collision, or other accidents. 2. Do not operate the machine in confined areas without proper ventilation. 3.
- Page 3 CARTON CONTENTS #07337 Vinyl Enclosure for Workman MD series Key # Part # Description 60046 Rear Post, RH (tagged) 60047 Rear Post, LH 60277 Front Post, RH (tagged) 60278 Front Post, LH 60048 Top Frame, RH (tagged) 60049 Top Frame, LH...
- Page 4 Step 1: Identify the frame parts using the parts list and the above illustration.
- Page 5 WARNING ! The following procedure to vent the fuel tank is required to prevent the build up of gasoline fumes inside the cab. Gasoline fumes can ignite causing serious injury or death. NOTE: Installation of this enclosure on any MDE electric unit and 2010 & up gasoline models does not require Step 2.
- Page 6 Step 3; See Figure 3A & 3B: Install right and left Rear Posts (1 & 2). IMPORTANT ! If a ROPS bar is in place remove the bolts from the ROPS bar and attach the rear posts on top of the ROPS bar using the 3/8” x 1” bolts and 3/8”...
- Page 7 Step 5; See Figure 5: Install the right and left Front Post (3 & 4) A. Place the right Front Post into position as shown. B. Insert a 5/16” x 1” bolt with flat washer inwards through the slotted tab at Reference B, the dash and then the Dash Support Bracket into the clip nut.
- Page 8 Step 7; See Figure 7: Install Door Post right and left (7 & 9), Top Cross Bar (8) and Rear Bow (13). A. Hold the upper left Door Post in place over the two holes at the top. Insert two 1/4” x 2” bolts inwards through the holes.
- Page 9 Step 9; See Figure 9: Install Windshield (11) A. Set the Windshield in place between the Front Posts and Top Frames. Place a 1/4” lock washer over each of four 1/4” x 1 1/2” bolts. Align the holes in the parts and insert the bolts into the tapped holes.
- Page 10 Step 11; See Figure 11A, 11B, & 11C: Install right and left Doors (16 & 18), right and left Door Bottoms (17 & 19), Door Hinges, and Door Latches, A. Bolt two door Hinges to the Door Post using 1/4” x 5/8” bolts and 1/4” lock washers to attach hinges to the out side of the Door Post.
- Page 11 Step 12; See Figure 12A, 12B & 12C: Install Rubber Door Seal. Cab frame / Door alignment. IMPORTANT ! The ‘U’ shaped section of the rubber door seal will be applied to the edge of the door. The ‘tube’ shaped section of the rubber door seal should be between the doorframe and the cab fram e.
- Page 12 Step 13; See Figure 13: ® Install adhesive hook Velcro for Front Panel Vinyl. ® A. Cut a strip of adhesive hook Velcro 45” long and apply to the lower front edge of the Windshield as indicated by the arrows. ®...
- Page 13 Step 15; See Figure 15: ® Install adhesive hook Velcro ® A. Cut two strips of adhesive hook Velcro 17” long and 3” long and apply to the bottom side of both ® Velcro Strips Top Frames as indicated by the arrows. 17”...
- Page 14 IMPORTANT ! Before continuing to STEP 17, check the position of the rear bow with Figure 14B and adjust accordingly. Step 17: Install Top / Rear Curtain ® A. Cut a 40” piece of adhesive hook Velcro (DO NOT remove protective backing strip) Press the ®...