Advertisement

MEX-GS810BH/N6000BH
SERVICE MANUAL
Ver. 1.0 2014.06
The service manual of the mechanism deck, used in
this model, has been issued in a separate volume.
Please refer to the service manual of the MG-101
series for the mechanism deck information.
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS
CEA2006 Standard
Power Output: 17 Watts RMS × 4 at 4
Ohms < 1% THD+N
SN Ratio: 80 dBA
(reference: 1 Watt into 4 Ohms)
Tuner section
FM
Tuning range: 87.5 – 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio (stereo):
79 dB (Conventional broadcast)
80 dB (HD Radio broadcast)
Separation at 1 kHz:
50 dB (Conventional broadcast)
80 dB (HD Radio broadcast)
Frequency response:
20 - 15,000 Hz (Conventional broadcast)
20 - 20,000 Hz (HD Radio broadcast)
AM
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
9,115 kHz or 9,125 kHz/5 kHz
Sensitivity: 26 μV
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and flutter: Below measurable limit
Corresponding codec: MP3 (.mp3) and WMA (.wma)
9-896-020-01
Sony Corporation
2014F33-1
©
2014.06
Published by Sony Techno Create Corporation
Photo: MEX-GS810BH
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
USB Player section
Interface: USB (High-speed)
Maximum current:
MEX-N6000BH: 1 A
MEX-GS810BH: 1 A (front), 2.1 A (rear)
The maximum number of recognizable tracks:
10,000
Corresponding codec:
MP3 (.mp3), WMA (.wma) and WAV (.wav)
Wireless Communication
Communication System:
BLUETOOTH Standard version 3.0
Output:
BLUETOOTH Standard Power Class 2
(Max. +4 dBm)
Maximum communication range:
Line of sight approx. 10 m (33 ft)*
1
Frequency band:
2.4 GHz band (2.4000 – 2.4835 GHz)
Modulation method: FHSS
Compatible BLUETOOTH Profiles*
2
:
A2DP (Advanced Audio Distribution Profile) 1.3
AVRCP (Audio Video Remote Control Profile) 1.5
HFP (Handsfree Profile) 1.6
PBAP (Phone Book Access Profile)
SPP (Serial Port Profile)
MAP (Message Access Profile)
HID (Human Interface Device Profile)
*1 The actual range will vary depending on factors such
as obstacles between devices, magnetic fields
around a microwave oven, static electricity,
reception sensitivity, antenna (aerial)'s performance,
operating system, software application, etc.
*2 BLUETOOTH standard profiles indicate the purpose
of BLUETOOTH communication between devices.
US Model
MEX-GS610BT
MG-101CF-188
DAX-25A
Power amplifier section
Output: Speaker outputs
Speaker impedance: 4 – 8 ohms
Maximum power output: 55 W × 4 (at 4 ohms)
General
Outputs:
Audio outputs terminal (front, rear, sub)
Power antenna (aerial)/Power amplifier control
terminal (REM OUT)
Inputs:
SiriusXM input terminal
Remote controller input terminal
Antenna (aerial) input terminal
MIC input terminal
AUX input jack (stereo mini jack)
USB port:
MEX-N6000BH: front
MEX-GS810BH: front, rear
Power requirements: 12 V DC car battery (negative
ground (earth))
Dimensions:
Approx. 178 mm × 50 mm × 177 mm
(7
1
/
in × 2 in × 7 in) (w/h/d)
8
Mounting dimensions:
Approx. 182 mm × 53 mm × 160 mm
(7
1
/
in × 2
1
/
in × 6
5
/
in) (w/h/d)
4
8
16
Mass: Approx. 1.2 kg (2 lb 11 oz)
Package contents:
Remote commander (1): RM-X231
Microphone (1)
Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.
AUDIO SYSTEM

Advertisement

Table of Contents
loading

Summary of Contents for Sony MEX-GS810BH

  • Page 1 Ohms < 1% THD+N MEX-N6000BH: 1 A Maximum power output: 55 W × 4 (at 4 ohms) SN Ratio: 80 dBA MEX-GS810BH: 1 A (front), 2.1 A (rear) (reference: 1 Watt into 4 Ohms) General The maximum number of recognizable tracks:...
  • Page 2 Digital Corp. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. The N-Mark is a trademark or registered trademark of NFC Forum, Inc.
  • Page 3: Table Of Contents

    MEX-GS810BH/N6000BH SECTION 1 SERVICING NOTES TABLE OF CONTENTS NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT SERVICING NOTES ..........The laser diode in the optical pick-up block may suffer electro- GENERAL static break-down because of the potential difference generated by ..............
  • Page 4 MEX-GS810BH/N6000BH DESTINATION SETTING METHOD 1-3. Entering the Destination Code When the complete MAIN board or IC502 on the MAIN board is • Method of operation by main unit replaced, the destination setting is necessary. 1. Destination Setting Set destination according to the procedure below.
  • Page 5 MEX-GS810BH/N6000BH 2. Confi rmation After Destination Setting REPLACING THE LITHIUM BATTERY OF THE REMOTE Execute the following operation after completing the destination COMMANDER setting, and confi rm a correct destination was set. When the battery becomes weak, the range of the remote commander becomes shorter.
  • Page 6 MEX-GS810BH/N6000BH IMPORTANT NOTE OF “INITIALIZING” OPERATION CHECK OF THE NFC AFTER COMPLET- The purpose of “Bluetooth Initialize” is to initialize the Bluetooth ING THE REPAIRS connection history (HF/Audio Streaming). (To delete the device After completing the repairs of this unit, follow the procedure below information for the devices that you connected to when searching, to check normal operation of the NFC.
  • Page 7 1. Search for this unit from the Bluetooth device (cellular phone), • Speaker connection (at least Front L/R ch) and confi rm whether this unit (“Sony Car Audio”) is displayed. • DC power supply (12 V) 2. Search for the distance of this unit and the Bluetooth device (cellular phone) about 5 m apart.
  • Page 8 MEX-GS810BH/N6000BH BLUETOOTH INFORMATION WRITING METHOD 2. Writing the NFC Tag Data When the complete MAIN board, knob (VOL) (SV) assy or front Write the NFC tag data (Bluetooth information) to the NFC mod- panel (SV) (assy) is replaced, the writing of Bluetooth information ule in the knob (VOL) (SV) assy.
  • Page 9 MEX-GS810BH/N6000BH 5. Input the Bluetooth address (BD_ADDR). 10. Check the operation of connecting with the smartphone by one (Input the Bluetooth address (BD_ADDR) that written on the touch (NFC). BT module label with the keyboard on the smartphone, or Tap “OPERATION CHECK OF THE NFC AFTER...
  • Page 10 MEX-GS810BH/N6000BH 16. Tap the “Read” on the screen of the smartphone. 4. Check Method of the NFC Tag Data Check the NFC tag data according to the procedure below. Procedure: 1. Set the unit to the state where the BT module (Ref. No. IC1002 on the MAIN board) can be seen.
  • Page 11 MEX-GS810BH/N6000BH 5. The Factor that One Touch Connection is Impossible The four following factors are considered as the factor that one touch connection is impossible. Guess and check the defective factor by each checking result. Note: The four following factors are examples.
  • Page 12 MEX-GS810BH/N6000BH AFFIXING OF LABEL (SERIAL NUMBER) When the front panel (SV) (assy) is replaced, it is necessary to affi x the label (serial number). 2 labels (serial number) are included with a new front panel (SV) (assy). Affi x 1 label to the rear side of the front panel (SV) (assy). Affi x the other one to the bottom side of main unit.
  • Page 13 MEX-GS810BH/N6000BH • Please cut out along the dotted line and use it. Notice about the serial number change on the back side of Notice about the serial number change on the back side of the front panel: the front panel:...
  • Page 14 MEX-GS810BH/N6000BH MEMO...
  • Page 15 MEX-GS810BH/N6000BH SERVICE POSITION CD mechanism deck CD mechanism deck insulating sheet insulating sheet stand stand cable flexible flat (27 core) cable flexible flat (27 core) main unit main unit Note: Do not cable flexible flat (27 core) is Note: Do not cable flexible flat (27 core) is damaged by the edge of the chassis.
  • Page 16: General

    USB device Tuner* Sintonizador para vehículo Teléfono inteligente* iPod/iPhone* , dispositivo USB SiriusXM Connect * MEX-GS810BH only Solo MEX-GS810BH Ferrite sleeve Manguito de ferrita Fuse (10 A) Fusible (10 A) RCA pin c ord (not supplied). Depending on the type of c...
  • Page 17 You may not be able to install this unit in some makes Keep the microphone away from extremely high automóvil japonés ( ) of Japanese cars. In such a case, consult your Sony temperatures and humidity. Para capturar la voz durante llamadas con manos dealer.
  • Page 18: Disassembly

    MEX-GS810BH/N6000BH SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW FRONT PANEL SECTION Note: Illustration of disassembly is omitted. 3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), COVER (Page 18) 3-3. SUB PANEL ASSY (Page 19) 3-4.
  • Page 19: Sub Panel Assy

    MEX-GS810BH/N6000BH 3-3. SUB PANEL ASSY 2 two claws 3 sub panel assy Note: When installing the sub panel assy, align two ribs and two holes. hole hole 2 two claws 1 two screws (PTT2.6 3-4. CD MECHANISM DECK (MG-101CF-188) Note 1: The service manual of the mechanism deck, used in this model has been issued in a separate volume.
  • Page 20: Connection Cable (Automobile) ( ) (Cnc1) (Gs810Bh)

    MEX-GS810BH/N6000BH 3-5. CONNECTION CABLE (AUTOMOBILE) ( ) (CNC1) (GS810BH) 5 connection cable (automobile) ( (CNC1) 4 screw (PTT2.6 2 Remove the cable 1 filament from two lead pins. tape 3 connector (CN1300) lead pin lead pin 2 Remove the cable from lead pin.
  • Page 21: Main Board

    MEX-GS810BH/N6000BH 3-6. MAIN BOARD Note 1: When the complete MAIN board is replaced, it is necessary to re- place knob (VOL) (SV) assy simultaneously. Also, the destination setting, Bluetooth operation check and Bluetooth information writ- ing are necessary. Refer to “DESTINATION SETTING METHOD”...
  • Page 22: Antenna Bt (Bt1) (Gs810Bh)

    MEX-GS810BH/N6000BH 3-7. ANTENNA BT (BT1) (GS810BH) 3 lead wire with connector (CN1002) lead wire from antenna BT MAIN connector connector board 2 connector (CN1002) (CN1300) (CN1300) antenna BT Note: Connection cable lead pin (automobile) do not front side ride on connector.
  • Page 23: Test Mode

    MEX-GS810BH/N6000BH SECTION 4 TEST MODE SETTING THE TEST MODE Setting method: 1. In the state of source off (the clock is displayed on the liquid crystal display), enter the test mode by pressing the buttons in order of the [ 4] t [MIC 5] t [V ALBUM 1] (press only the [V ALBUM 1] button for two seconds).
  • Page 24: Diagrams

    MEX-GS810BH/N6000BH SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - SERVO/BT/USB Section - CD MECHANISM DECK BLOCK (MG-101CF-188) FL, RL, SUB FPI1 RFRP 27 RFZI DAO3 (F_L-CH) (Page 17 FPI2 DAO2 (F_R-CH) R-CH 16 FNI1 DAO4 (R_L-CH) 15 FNI2 DAO1 (R_R-CH) R-CH...
  • Page 25: Block Diagram - Main Section

    MEX-GS810BH/N6000BH 5-2. BLOCK DIAGRAM - MAIN Section - INPUT SELECTOR, ELECTRICAL VOLUME IC402 J401 FL, RL, SUB 33 AU_IN_FL AU_OUT_FL FRONT (Page R-CH 31 AU_IN_RL AU_OUT_RL REAR AUDIO OUT R-CH 30 AU_IN_SUB AU_OUT_SL KEY BOARD (2/3) AU_OUT_SR AUX_L 8 AUX_LCH...
  • Page 26: Block Diagram - Panel/Power Supply Section

    MEX-GS810BH/N6000BH 5-3. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section - RESET SYSTEM CONTROLLER IC503 (3/3) (Page RESET SIGNAL 120 RC_IN1 GENERATOR J801 IC501 81 RC_IN0 (REMOTE IN) KEY_ACK0 +1.2V -COM_1.2V REGULATOR IC03 KEY BOARD (3/3) LCD_DATA 40 LCD_DO REGULATOR +1.5V LCD_CLK...
  • Page 27 MEX-GS810BH/N6000BH THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Waveforms (In addition to this, the necessary note is printed in each block.) – MAIN Board – For Printed Wiring Boards. For Schematic Diagrams. Note: Note: IC705 rk (LRCK_OUT) IC503 ua (XTAL) •...
  • Page 28: Printed Wiring Boards - Main Section (1/2)

    MEX-GS810BH/N6000BH 5-4. PRINTED WIRING BOARDS - MAIN Section (1/2) - • : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) C329 C310 C332 R834 D808 IC801 C315 C307 R303 C807 D805 C811 D807 R831 C816 C825 R439 C305 R821 C312 R323...
  • Page 29: Printed Wiring Boards - Main Section (2/2)

    MEX-GS810BH/N6000BH 5-5. PRINTED WIRING BOARDS - MAIN Section (2/2) - • : Uses unleaded solder. MAIN BOARD (CONDUCTOR SIDE) (FRONT VIEW) J401 CN301 AUDIO OUT J1001 J801 REAR FRONT (REMOTE IN) J001 R302 CL301 (ANTENNA IN) CN801 REAR LCH (+)
  • Page 30: Schematic Diagram - Main Section (1/5)

    MEX-GS810BH/N6000BH 5-6. SCHEMATIC DIAGRAM - MAIN Section (1/5) - • See page 27 for Waveforms. • See page 35 for IC Block Diagrams. • See page 38 for IC Pin Function Description. MAIN BOARD (1/5) JL725 R728 C767 C764 C770...
  • Page 31: Schematic Diagram - Main Section (2/5)

    MEX-GS810BH/N6000BH 5-7. SCHEMATIC DIAGRAM - MAIN Section (2/5) - • See page 27 for Waveforms. • See page 35 for IC Block Diagrams. • See page 38 for IC Pin Function Description. MAIN BOARD (2/5) (N6000BH) (GS810BH) R1054 R1173 MAIN...
  • Page 32: Schematic Diagram - Main Section (3/5)

    MEX-GS810BH/N6000BH 5-8. SCHEMATIC DIAGRAM - MAIN Section (3/5) - • See page 35 for IC Block Diagrams. J401 MAIN BOARD (3/5) IC B/D FRONT IC301 Q403 - 408 AUDIO OUT LTC914TUBFS8TL (GS810BH) POWER AMP LTC014TUBFS8TL (N6000BH) (N6000BH) IC301 PURE5001H-4WX REAR...
  • Page 33: Schematic Diagram - Main Section (4/5)

    MEX-GS810BH/N6000BH 5-9. SCHEMATIC DIAGRAM - MAIN Section (4/5) - • See page 27 for Waveforms. • See page 35 for IC Block Diagrams. MAIN BOARD (4/5) FB801 J801 (REMOTE IN) FB802 L1310 4.7uH FB803 D817 D816 DZ2J07500L RSX051VA-30 JL806 FB805...
  • Page 34: Schematic Diagram - Main Section (5/5)

    MEX-GS810BH/N6000BH 5-10. SCHEMATIC DIAGRAM - MAIN Section (5/5) - • See page 27 for Waveforms. • See page 35 for IC Block Diagrams. • See page 38 for IC Pin Function Description. MAIN BOARD (5/5) IC B/D IC501 RESET SIGNAL GENERATOR...
  • Page 35 MEX-GS810BH/N6000BH • IC Block Diagrams – MAIN Board – IC01, 03 S-13A1A12-E6T1U3 IC02 NJM2884U1-33 (TE2) VOUT 1 OVERCURRENT PROTECTION THERMAL THERMAL SHUTDOWN PROTECTION BANDGAP REFERENCE ON/OFF CONTROL – REFERENCE VOLTAGE VSS 2 ON/OFF 3 INRUSH CURRENT LIMITING IC301 PURE5001H-4WX HIGH SIDE...
  • Page 36 MEX-GS810BH/N6000BH IC402 BD3468FV-E2 FADER FADER BOOST LEVEL OUTC SHIFT SELECTION FADER FADER BOOST LEVEL OUTS SHIFT A1 1 A2 2 LEVEL FADER FADER OUTR1 SHIFT BOOST BP1 3 REAR SELECTION FADER FADER LEVEL OUTR2 BOOST SHIFT BP2 4 CP1 5...
  • Page 37 MEX-GS810BH/N6000BH IC803 BD49100RFS-E2 IC804 BD60HC0WEFJ-E2 LDO5 ADJ5 1 44 GATE5 (CONTROLLER) INTERNAL REGULATOR EN 2 BU_SW OVER CURRENT LD4EN 3 43 VIN0 PRORECITON UVLO BU_CONT L_DET ECO 4 42 BCAP SOFT – – START ERR1 5 41 VINSW ERR2 6 THERMAL 40 N.C.
  • Page 38 Serial data output to the front panel block MEC_EJECT Loading motor drive signal (eject direction) output terminal “H”: motor on Frequency control signal output to the regulator and DC/DC converter (MEX-GS810BH) SYNC_OUT Frequency control signal output to the regulator (MEX-N6000BH) DEBUG_TX...
  • Page 39 PVcc Power supply terminal (+3.3V) (for I/O) USB power on/off control signal output to the DC/DC converter “H”: power on USB_ON2 (MEX-GS810BH only) USB over current detection signal input from the DC/DC converter “L”: over current USB_OVR2 (MEX-GS810BH only) BT_PWR Power on/off control signal output terminal for the Bluetooth section “H”: power on...
  • Page 40 Power supply terminal (+3.3V) (for USB digital) USBDPVss Ground terminal (for USB digital) Two-way USB data (–) bus with the USB controller (MEX-GS810BH) Two-way USB data (–) bus with the USB connector (MEX-N6000BH) Two-way USB data (+) bus with the USB controller (MEX-GS810BH)
  • Page 41 MEX-GS810BH/N6000BH MAIN BOARD IC705 TC94A99FG-003 (SYCH (RF AMP, DIGITAL SERVO PROCESSOR, AUDIO DSP) Pin No. Pin Name Description LPFO PLL circuit low-pass fi lter amplifi er output terminal PVREF PLL circuit reference voltage (+1.65V) terminal VCOF VCO fi lter terminal...
  • Page 42 MEX-GS810BH/N6000BH Pin No. Pin Name Description DVSS5 Ground terminal VDD1-3 Power supply terminal (+1.5V) VSS-2 Ground terminal XVSS3 Ground terminal System clock input terminal (16.9344 MHz) System clock output terminal (16.9344 MHz) XVDD3 Power supply terminal (+3.3V) ADVDD3 Power supply terminal (+3.3V)
  • Page 43 MEX-GS810BH/N6000BH MAIN BOARD IC1301 PD720114GA-YEU-A-SAK (USB CONTROLLER) Pin No. Pin Name Description VDD25OUT Internal regulator power supply voltage (+2.5V) output terminal VSSREG Ground terminal (for internal regulator) 3 to 6 LED4 to LED1 LED drive signal output terminal Not used...
  • Page 44: Exploded Views

    MEX-GS810BH/N6000BH SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference they may have some difference from the number in the exploded views are not sup- original one. plied. • Items marked “*” are not stocked since •...
  • Page 45: Chassis Section

    MEX-GS810BH/N6000BH 6-2. CHASSIS SECTION (GS810BH) CNC1 not supplied not supplied MAIN board not supplied TU01 not supplied not supplied not supplied (N6000BH) Note: When the complete MAIN board is replaced, it is necessary to replace knob (VOL) (SV) assy simultaneously. Also, the destination setting, Bluetooth operation check and Bluetooth information writing are necessary.
  • Page 46: Electrical Parts List

    MEX-GS810BH/N6000BH SECTION 7 MAIN ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- uF: μF the parts list may be different from the ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 47 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C410 1-124-779-00 ELECT CHIP 10uF C541 1-116-737-11 CERAMIC CHIP 1uF C411 1-162-923-11 CERAMIC CHIP 47PF C543 1-118-386-11 CERAMIC CHIP 0.1uF C412 1-100-966-91 CERAMIC CHIP 10uF C544 1-118-386-11 CERAMIC CHIP 0.1uF...
  • Page 48 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C750 1-128-996-11 ELECT CHIP 4.7uF * C817 1-118-035-11 CERAMIC CHIP 0.1uF C751 1-116-728-11 CERAMIC CHIP 2.2uF (N6000BH) C754 1-118-386-11 CERAMIC CHIP 0.1uF C817 1-118-386-11 CERAMIC CHIP 0.1uF...
  • Page 49 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C865 1-116-705-11 CERAMIC CHIP 47uF C1321 1-118-386-11 CERAMIC CHIP 0.1uF (N6000BH) (GS810BH) C865 1-118-929-11 CERAMIC CHIP 47uF C1322 1-118-386-11 CERAMIC CHIP 0.1uF (GS810BH) (GS810BH) C866 1-116-705-11...
  • Page 50 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D401 6-502-961-01 DIODE DA2J10100L IC502 6-721-746-01 IC MX25L3235EM2I-10G-A03 (for SERVICE) D501 6-503-759-01 DIODE RB751V40, 115 (See Note 1) D502 6-503-759-01 DIODE RB751V40, 115 IC503 6-721-341-01 IC R7S7200032CFP...
  • Page 51 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q701 6-551-120-01 TRANSISTOR 2SA2119K R320 1-216-833-11 METAL CHIP 1/10W (GS810BH) Q801 6-552-936-01 TRANSISTOR LTC014EUBFS8TL Q802 6-552-922-01 TRANSISTOR LTA014EUBFS8TL R320 1-216-864-11 SHORT CHIP 0 (N6000BH) Q803 6-553-498-01...
  • Page 52 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R510 1-218-953-11 METAL CHIP 1/16W R579 1-250-553-11 METAL CHIP 270K 1/16W R511 1-218-953-11 METAL CHIP 1/16W R582 1-218-977-11 METAL CHIP 100K 1/16W R512 1-218-941-81 METAL CHIP...
  • Page 53 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R649 1-218-941-81 METAL CHIP 1/16W R748 1-218-983-11 METAL CHIP 330K 1/16W R650 1-218-941-81 METAL CHIP 1/16W R749 1-218-977-11 METAL CHIP 100K 1/16W R651 1-218-941-81 METAL CHIP...
  • Page 54 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R839 1-250-563-11 METAL CHIP 680K 1/16W R1030 1-218-941-81 METAL CHIP 1/16W * R840 1-250-545-11 METAL CHIP 120K 1/16W R1031 1-218-957-11 METAL CHIP 2.2K 1/16W R1032 1-218-965-11...
  • Page 55 MEX-GS810BH/N6000BH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1369 1-216-864-11 SHORT CHIP PARTS FOR INSTALLATION AND CONNECTIONS R1370 1-218-965-11 METAL CHIP 1/16W ************************************** R1372 1-216-864-11 SHORT CHIP X-2583-962-1 FRAME ASSY, FITTING < TUNER UNIT >...
  • Page 56 MEX-GS810BH/N6000BH REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2014.06...

This manual is also suitable for:

Mex-n6000bh

Table of Contents