TachoReader Basic uses tachograph power supply while retrieving data, so no external power source is required. It is small, easy and convenient to use. Fig. TachoReader Basic. 2. Installation The device is not supported by Windows® 2000 and earlier operating systems.
Operating modes 3. Operating modes TachoReader Basic works in different modes. They depend on: connection type - whether the device operates standalone, is connected to a computer or · tachograph; Driver card download via tachograph option in the device configuration window.
Configuration 4. Configuration Device configuration window can be launched in two different ways: TachoReaderConfigurator.exe Directly from the device memory - file; Using 4Trans or TachoScan - program menu. When you first start configuration, Windows® may prompt for installing . We recommend .NET Framework that you accept - otherwise you will not be able to start the configurator.
Page 7
Configuration For example, you can set up data retrieval from the digital tachograph as and downloading data from the driver card as Description of data download options: Overview - basic information about the tachograph; · Events and faults - reading events (e.g. driving without card) and failures (e.g. power ·...
To confirm the configuration changes, click 5. Download from tachograph Operations after connecting to a computer: TachoReader Basic Open the configuration window, and then, for any selected configuration button, choose the type and scope of activities to be downloaded (see: "Configuration...
Page 9
After reading the company card some tachographs may request "unlocking" confirmation. In this case, "unlock" the tachograph, or "Technical data" and "Activities" will not be downloaded. As soon as TachoReader Basic you connect to the tachograph, select the type of configuration you have set on your computer.
" topic for more). When the download is finished, the device will play a short tune and a the LED will blink steadily green. TachoReader Basic Disconnect from the tachograph and remove the company card. The data is saved to a file (Vehicle reg.no._Date and time of data download.DDD), which is placed in the TACHO folder in the device memory.
Page 11
( The special data is always downloaded in full, regardless of the selected period of time. Fig. Device configuration window: TachoReader Basic. – Downloading data begins after selecting the configuration:...
Download from driver card 6. Download from driver card TachoReader Basic can download simultaneously or individually the data from a driver card inserted in the tachograph and the tachograph data. This depends on the settings described below. Operations after connecting to a computer: Open the device configuration window (see: "Configuration...
If, after you inserting the device into the tachograph slot, you do not switch the configuration immediately, after approximately 5 seconds TachoReader Basic will start the download automatically with configuration. after approx. 5 seconds the device will automatically start downloading data. The download will be indicated with the LED blinking green-red, or green only (there may be times when the LED will be off).
4Trans / TachoScan software. To do this, use windows or other file explorer to copy the files and move them to the desired location (TachoReader Basic is installed on your computer as a separate drive named "...
Page 15
Error codes Description of error types: One red LED blink Cause o data transmission. Solution Insert the company card. Wait until the company card is read by the tachograph. Repeat reading from tachograph. Two red LED blinks Cause Too little data downloaded. Solution Repeat reading from tachograph.
Page 16
Error codes Three red LED blink Cause There is not enough free memory. Solution Transfer the source files to another media (such as a computer disk) Repeat reading from tachograph. Minimum available storage space in the device memory is 10 MB. Four red LED blinks Cause Invalid file system.
Page 17
Repeat reading from tachograph. Seven red LED blinks Cause Incorrect data in the configuration file or other unrecogni ed error. Solution TachoReader Basic Connect to the computer. In the device configuration window click on (see: "Configuration " topic for more),...
Page 18
Error codes The LED is off Cause o power. Solution ake sure the tachograph is switched on. Repeat reading from tachograph.
Error codes 9. Additional information 9.1. The company INELO Polska sp. z o.o. ul. Karpacka 24/U2b 00 Bie o - Bi ł POLAND o@ine 33 4 96 58 71 33 4 96 58 71 (111)