Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for inelo TachoReader Basic
Summary of Contents for inelo TachoReader Basic
- Page 1 TachoReader Basic Tutorial Version: 1.0...
- Page 2 TachoReader Basic Tutorial © 2002 - 2017 INELO All rights reserved All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher.
-
Page 3: Table Of Contents
Table of Contents Table of Contents 1. Introduction ..............................4 2. Installation ..............................4 3. Operating modes ..............................4 4. Configuration ..............................5 5. Download from tachograph ..............................7 6. Download from driver card .............................. -
Page 4: Introduction
2. Installation The device is not supported by Windows® 2000 and earlier operating systems. To install TachoReader Basic on a computer, simply connect it to the USB port and wait until Windows® installs it automatically. When it detects a new device, Windows® automatically installs it as a new mass storage disk. -
Page 5: Configuration
Power supply: from the computer. Operation in USB mode - the possibility to configure the device (run the "TachoReaderConfigurator.exe" file placed in the TachoReader Basic memory), possibility to read/write data from/to the device and work with 4Trans and TachoScan. Driver card download via tachograph option - does not affect this mode of ·... - Page 6 Configuration 2. Using 4Trans or TachoScan - program menu. When you first start configuration, Windows® may prompt for installing . We recommend .NET Framework that you accept - otherwise you will not be able to start the configurator. will be automatically downloaded and installed by the operating system. .NET Framework Fig.
-
Page 7: Download From Tachograph
To confirm the configuration changes, click 5. Download from tachograph Operations after connecting to a computer 1. Open the TachoReader Basic configuration window, and then, for any selected configuration of: button, choose the type and scope of activities to... - Page 8 After reading the company card some tachographs may request "unlocking" confirmation. In this case, "unlock" the tachograph, or "Technical data" and "Activities" will not be downloaded. 3. As soon as you connect TachoReader Basic to the tachograph, select the type of configuration you have set on your computer.
-
Page 9: Download From Driver Card
TACHO folder in the device memory. 6. Download from driver card TachoReader Basic can download simultaneously or individually the data from a driver card inserted in the tachograph and the tachograph data. This depends on the settings described below. - Page 10 4. Use the button to select the appropriate configuration: If, after you inserting the device into the tachograph slot, you do not switch the configuration immediately, after approximately 5 seconds TachoReader Basic will start the download automatically with configuration. after approx. 5 seconds the device will automatically start downloading data. The download will be indicated with the LED blinking green-red, or green only (there may be times when the LED will be off).
-
Page 11: Transferring Data Files Into Pc
4Trans / TachoScan software. To do this, use windows or other file explorer to copy the files and move them to the desired location (TachoReader Basic is installed on your computer as a separate drive named "... -
Page 12: Error Codes
Error codes 8. Error codes Errors are indicated by a specific number of red LED blinks. To identify the type of error, count the number of red LED blinks. The LED blinks red twice, then there is a pause and the whole cycle is repeated. This means that the key is signaling the error by blinking red twice. - Page 13 Error codes Solution 1. Transfer the source files to another media (such as a computer disk) 2. Repeat reading from tachograph. Minimum available storage space in the device memory is 10 MB. Four red LED blinks Cause Invalid file system. Solution 1.
- Page 14 Repeat reading from tachograph. Seven red LED blinks Cause Incorrect data in the configuration file or other unrecogni z ed error. Solution 1. Connect TachoReader Basic to the computer. 2. In the device configuration window click on (see: "Configuration " topic for more), 3.
-
Page 15: Additional Information
9.1. The company ul. Karpacka 24/U2b 43-300 Bielsko - Biała POLAND e-mail: biuro @ inelo.pl tel.: + 4 8 33 4 9 6 5 8 7 1 fax.: + 4 8 33 4 9 6 5 8 7 1 (111) www.inelo.pl 9.2. Support...