Related Manuals for ELSYS.se ERS CO2 Lite
Summary of Contents for ELSYS.se ERS CO2 Lite
- Page 1 Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se Specifications in this document are subject to change without notice. ©Elektroniksystem i Umeå AB 2020...
-
Page 2: Important Safety Information
For additional information and how to carry out disposal, please contact the certified disposal service providers. The sensors contain a lithium battery, which must be disposed of separately. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 3: Table Of Contents
Sampling mode / Periodic measurement .............. 12 Schedule Transmission ..................... 12 Specifications ........................13 Sensor payload format ....................13 Regulations ........................14 Legal Notices ......................14 Declaration of conformity ..................14 Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 4: Description
NFC (Near Field Communication) and can easily be configured from a smartphone. The barcode contains DevEUI and sensor type. This label is located at the back of your device, Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 5: Main Features Of Ers Co Lite
After approximately 24 days the sensor will be self-calibrated. Forced calibration is not required in normal environments. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 6: How To Calibrate
For these applications, the ABC function must be turned off. Without ABC operating, the sensor should be calibrated manually every two or three years. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 7: Installation
Caution: Using batteries other than the ones provided may result in loss of performance and battery life, and also damage to the device. Dispose of properly, observing environmental protection rules. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 8: Service And Maintenance
5. Attach the sensor part to the back panel. Service and maintenance No serviceable parts inside. If service is needed other than battery replacement, please contact your distributor. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 9: Sensor Configuration
7. Wait for the sensor to reboot (5 sec), indicated by the LED flashing. Sensor settings have been updated. See the section “Help” in the application for more information. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 10: Over The Air Configuration
When you have written data to the sensor, let the sensor reboot and restart before trying to write again. You should always validate your settings by reading the NFC data after the sensor has restarted. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 11: Sensor Startup
After successful connection to a network, the sensor sends a settings packet and enters sampling mode. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 12: Sampling Mode / Periodic Measurement
Note: The configured sending interval can be overridden by network limitations. Due to this, the spreading factor and sending interval settings might result in longer intervals than intended. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 13: Specifications
**Accuracy is met at 10 – 40°C, 0 – 60%RH, after minimum three (3) performed Automatic Baseline Corrections, preferably spanning eight (8) days in-between, or a successful zero-calibration ***Depending on settings and environmental factors. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 14: Regulations
Declaration of conformity å Hereby, Elektroniksystem i Ume AB declares that ERS CO Lite complies with the essential requirements and other relevant provisions of Directive 2014/30/EU and 2014/53/EU. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
Need help?
Do you have a question about the ERS CO2 Lite and is the answer not in the manual?
Questions and answers