Related Manuals for ELSYS.se ERS Eye
Summary of Contents for ELSYS.se ERS Eye
- Page 1 Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se Specifications in this document are subject to change without notice. ©Elektroniksystem i Umeå AB 2020...
-
Page 2: Important Safety Information
For additional information and how to carry out disposal, please contact the certified disposal service providers. The sensors contain a lithium battery, which must be disposed of separately. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 3: Table Of Contents
Contents Important safety information ...................2 Description .........................4 Main features of ERS Eye ......................5 Installation ..........................6 Service and maintenance ....................7 Sensor configuration ......................8 NFC Configuration ........................8 Over the air configuration ......................9 Application parameters....................... 9 Sensor behavior .........................9 NFC Read / Write ........................9 Sensor startup ........................... -
Page 4: Description
Description ERS Eye is an advanced room occupancy and indoor climate sensor for LoRaWAN® wireless network. The sensor measures temperature, humidity, light intensity, and detects occupancy. It can detect occupancy based on body heat, not only by movement. ERS Eye is a battery-powered device and is designed to be mounted on the ceiling. -
Page 5: Main Features Of Ers Eye
Main features of ERS Eye • Compatible with LoRaWAN® specification 1.0.3 • Measures ambient temperature • Measures ambient humidity • Measures light intensity • Detects motion using a passive IR sensor • Detects occupancy using a Grid-Eye infra-red sensor •... -
Page 6: Installation
2. Mount the back panel securely to the wall with at least 2 appropriate screws, using some of the six mounting holes. Note: ERS Eye will calculate its first background picture 15s after inserting the batteries. It is preferable if the room is unoccupied at this time. Otherwise, it will take maximum 24h to recalibrate the background if the first background picture is inaccurate. -
Page 7: Service And Maintenance
3. Install the batteries. The ERS Eye requires one or two AA batteries. The battery type is 3.6V Lithium Battery (ER14505). You can use one battery, but it’s recommended that you use two for best performance and battery life. Use battery slot A if only one battery is used. -
Page 8: Sensor Configuration
7. Wait for the sensor to reboot (5 sec), indicated by the LED flashing. Sensor settings have been updated. See the section “Help” in the application for more information. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 9: Over The Air Configuration
When you have written data to the sensor, let the sensor reboot and restart before trying to write again. You should always validate your settings by reading the NFC data after the sensor has restarted. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 10: Sensor Startup
After successful connection to a network, the sensor sends a settings packet and enters sampling mode. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 11: Sampling Mode / Periodic Measurement
Note: The configured sending interval can be overridden by network limitations. Due to this, the spreading factor and sending interval settings might result in longer intervals than intended. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 12: Motion Detection Range
Note: The PIR Lens has a blanking time of 20 seconds right after motion event and transmission. Any movements during this time will be ignored PIR Lens detection pattern Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 13: Grid-Eye
The Grid-Eye heat map image will be postponed 5 minutes after every PIR motion detection. Room occupancy is set to 1 as long as motion is detected. Whenever occupancy value is changed, the ERS Eye will schedule transmission and go into sleep-mode. No triggered transmission will be done as long as occupancy value remains unchanged. - Page 14 Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
-
Page 15: Specifications
Up to 5 years** *Measured with settings: SF10, 868 Mhz. The range can be greater or less, depending on terrain and building structure. **Depending on settings and environmental factors. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se... -
Page 16: Regulations
Declaration of conformity å Hereby, Elektroniksystem i Ume AB declares that ERS Eye complies with the essential requirements and other relevant provisions of Directive 2014/30/EU and 2014/53/EU. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se...
Need help?
Do you have a question about the ERS Eye and is the answer not in the manual?
Questions and answers