Subscribe to Our Youtube Channel
Related Manuals for CORNING Stripettor
Summary of Contents for CORNING Stripettor
- Page 1 Corning Stripettor Ultra ® ™ Pipet Controller Instruction Manual Catalog Number: 4099 This manual is available in additional languages at www.corning.com/lifesciences.
- Page 2 H – Membrane filter – PP/PTFE PTFE: Polytetrafluoroethylene J – Connector gasket – SI SI: Silicone K – Battery cover – PP L – Battery – NiMH, AAA, 1.2V Casing – PP M – Wall mount – PP 2 – Corning Stripettor Ultra Pipet Controller...
- Page 3 Instruction Manual – 3...
-
Page 4: Table Of Contents
12. Spare Parts for Corning Cat. No. 4099 ....... . . -
Page 5: Introduction
1. Introduction The pipet controller is a device intended for pipetting liquids with the use of measuring pipets. It can work with all types of glass or plastic pipets in the volume range from 0.5 mL to 100 mL. Two dispense modes permit selection of dispensing intensity depend- ing on the user’s needs. -
Page 6: Limitations Of Use
CAUTION: Do not put aside the pipet controller if there is liquid in the pipet. 6 – Corning Stripettor Ultra Pipet Controller... - Page 7 Filling the pipet Before aspirating is started, set the speed by pressing the SPEED switch (Figure 1C) until the display shows the correct speed (Figure 1E). • HIGH speed - fast aspirating (Figure 2.1), • LOW speed - slow aspirating (Figure 2.2). It is recommended to set the LOW speed when working with pipets of volumes up to 5 mL, and the HIGH speed for pipets of volumes greater than 5 mL.
-
Page 8: Troubleshooting
• Remove the pipet. • Unscrew the nose piece (Figure 4.1). • Remove the membrane filter (Figure 4.1) and the pipet holder (Figure 4.2). • Rinse the holder using a wash bottle (Figure 4.3). 8 – Corning Stripettor Ultra Pipet Controller... -
Page 9: Charging The Batteries
• Blow liquid out of the holder and set it aside until it is completely dry. • Install new membrane filter (Figure 4.4) and assemble the device in reverse order. 8. Charging the Batteries CAUTION: The pipet controller may be charged only with the original charger. The mains voltage shall conform with the specification on the charger (Input: 100-240V, 50/60Hz, 0.2A;... -
Page 10: Components
During breaks in the work the pipet controller can be stored on the wall hanger or charging Stand. The Corning® Stripettor™ Ultra charging stand is a device intended to conveniently charge and store a pipet controller when not in use. Three positions (Figure 9) to store the pipet controller, depending on user needs, are also visible as icons printed on the stand. -
Page 11: Spare Parts For Corning Cat. No. 4099
ING DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof that proves defective in material or workmanship within the warranty period, provided the purchaser notifies Corning of any such defect. -
Page 12: Equipment Disposal
No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend the period of this warranty. For your reference, make a note of the serial and model number, date of purchase, and supplier here. - Page 13 Instruction Manual – 13...
- Page 14 Outside the United States, call +1.978.442.2200 or contact your local Corning sales office. © 2015, 2020 Corning Incorporated. All rights reserved. 3/20 CLS-EQ-113 REV4/H-STR-IM REV2 Corning Incorporated, Daniszewska 4, 03-230 Warsaw www.corning.com/lifesciences Made in Poland For a listing of trademarks, visit www.corning.com/clstrademarks. All other trademarks are the property of their respective owners.
Need help?
Do you have a question about the Stripettor and is the answer not in the manual?
Questions and answers