Related Manuals for Sol*Aire EXO 1000W
Summary of Contents for Sol*Aire EXO 1000W
- Page 1 Instruction Manual Ceramic Electric Radiator PLEASE READ AND SAVE THESE INSTRUCTIONS...
-
Page 2: Table Of Contents
Contents Safety Instructions Page 3 Installation Instructions Page 4-6 Operation Page 7-16 Manual Control Page 8-11 Setting time and Date Page 9 Setting the Timer Page 10 Additional Functions Page 11 Connecting to WiFi Page 12-13 Using the App Page 14-15 Factory Reset, High and Low Alarm, Maintenance Page 16 Power Consumption and Disposal... -
Page 3: Safety Instructions
Safety Instructions CAUTION - Some parts of this product can become very hot which could cause burns. Particular attention has to be given where children and vulnerable people are present. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person. The heater must not be located immediately below an electrical socket-outlet. - Page 4 Mounting the heater Make sure clearances shown below (on Fig1) are adhered to. Use the screws, dowels and brackets supplied by the manufacturer. 2. For drilling dimensions, see the drilling template. 3. Read the instructions for the steps on the installation as shown on the next page. Caution: Before switching on make sure the radiator is correctly fixed to the wall.
- Page 6 II / Technical specifications Power supply: 230V~ 50Hz Power: 1000W, 1500W, 2000W Power supply: 230V~ 50Hz - Temperature is ajustable by +/- 0.5°C - Temperature range setting: 7°C to 30°C...
-
Page 7: Operation
Operation Power on/off button Mode button Increase temperature / time Decrease temperature / time Icon Description Icon Description Time Sensor Mode Week (1 to 7) Low Surface Temperature Program (P1 to P7) Pilot Wire Mode Temperature Display Open Window Comfort Mode Child lock (Except Mechanical power switch on the back ) Eco Mode... -
Page 8: Manual Control
Manual Control (Without WiFi) When using, ensure the Radiator is switched on. Press ON / OFF (on control panel) button to turn the radiator on or off. To select a mode, Press the button, Comfort mode • The default Eco temperature is 19C . •... - Page 9 Setting the Time and Day Press + or - to set the hour. Press until the timer icon continue to setting the minute. (After 30 appears. Then hold seconds without input it automaticity 5 seconds. The hour digits will proceeds to the minute. ) flicker.
-
Page 10: Setting The Timer
Setting the Timer Follow the steps for setting the time until you see the below display. P1 Indicates which day is The 00 is the hour that is being programmed. being programmed. The heater starts at 00 for P1= Monday midnight, 01 for 1 o’clock P2=Tuesday and so forth. -
Page 11: Additional Functions
Additional Functions • Sensor Mode This mode will activate the radiator’s presence detection system. If the room is unoccupied, the radiator will automatically shift to Anti Frost mode. The time needed to activate the presence detection can be set to “0”, “15”, “30”, “45”... -
Page 12: Connecting To Wifi
Connecting to WiFi Before connecting ensure that the heater’s WiFi is turned on. • Press to put the radiator into standby mode. Then hold down for 5 seconds to enter the settings menu. • Press to skip through the settings until F4 appears on the screen, followed by the current setting. Default is “oF”... - Page 13 • The app will demonstrate that it has found the radiator. Press Next • 6. The app will ask you to enter and confirm your WiFi password. • The radiator will begin connecting. When it is successfully added, you can change the name of the radiator or press “Done”...
-
Page 14: Using The App
Using the App Home Overview You can use the Smart Life app to control multiple devices. All devices are displayed on the home screen with their status. Possible statuses: Online: Heater will respond to app commands. Offline: The heater cannot be controlled by the app. Either the heater is switched off or not communicating with the WiFi. - Page 15 Choose Mode Tap the mode icon on the control interface (No 4 on the previous page) to choose mode. The five options correspond to the five modes on the control panel. Setting the Timer Tap the program icon on the control interface to programme the timer.
- Page 16 Reset to Factory Settings To reset the Radiator, Press the button for for 10 seconds. This will restore factory settings. High and Low Temperature Alarm Error Code Problem Err 1 Ambient temperature sensor is disconnected or the ambient temperature is too low Err2 Ambient temperature sensor is short-circuited or the ambient temperature is too high...
- Page 17 Item Unit Type of heat input, for electric storage local space heaters only Manual heat charge control, with integrated thermostat Manual heat charge control with room and/or outdoor temperature feedback Electronic heat charge control with room and/or outdoor temperature feedback Fan assisted heat output Type of heat output/room temperature control (select one) single stage heat output and no room temperature control...
Need help?
Do you have a question about the EXO 1000W and is the answer not in the manual?
Questions and answers