Operation - Toolson PRO-ABH 2000 Original Operating Instructions

without the additional handle (10).
The additional handle (10) is secured to the
impact drill by a clamp. Turning the handle anti-
clockwise (viewed from the handle) will release
the clamp. Turning the handle clockwise tightens
the clamp.
Release the clamp of the additional handle fi rst.
Then you can swivel the additional handle (10)
into the most comfortable working position for
yourself. Now turn the additional handle (10) in
the opposite direction again until the additional
handle (10) is secure.
5.2 Fitting and adjusting the depth stop (Fig.
3/Item 11)
The depth stop (11) is held in position by the
locking screw (a).
•
Release the locking screw (a) and push the
depth stop (11) into the guide.
•
Set the depth stop (11) to the same level as
the drill bit.
•
Pull the depth stop back by the required dril-
ling depth.
•
Retighten the locking screw (a).
•
Now drill the hole until the depth stop (11)
touches the workpiece.
5.3. Inserting a tool (Fig. 4)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the equipment.
•
Clean the tool before fitting it and apply a thin
coating of bit grease to the tool shaft.
•
Turn and push the dust-free tool into the tool
mounting (b) as far as it will go. The tool will
lock automatically.
•
Check that the bit is locked in placed by
pulling on it.
5.4. Removing a tool (Fig. 5)
Pull back and hold the locking sleeve (1) and
remove the tool.
Anl_PRO_ABH_2000_SPK7.indb 20 Anl_PRO_ABH_2000_SPK7.indb 20
GB

6. Operation

6.1 Charging the LI battery pack (Fig. 6/7)
1. Pull the battery pack (5) out of the handle,
pressing the pushlock buttons (6) as you do
so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(8) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery
charger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that the Li battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the power of the cordless
impact drill drops.
6.2 Drill / Impact drill / Chisel selector switch
(Fig. 8)
•
For drilling, turn the rotary switch (2) to posi-
tion A.
•
For impact drilling, turn the rotary switch (2) to
position B.
•
To align the chisel for chiseling work, turn the
rotary switch (2) to position C.
•
In this position the chisel is not locked. Turn
the chisel into the required position by hand.
•
For chiseling work, turn the rotary switch (2)
to position D.
•
The chisel is locked in position D.
Important!
Switch position C is only intended to be used for
aligning the chisel.
For chiseling work you must therefore only use
switch position D, because in this position the
chisel is locked.
- 20 -
23.05.2018 14:12:42 23.05.2018 14:12:42