Page 1
Quick Start Thank you for purchasing the MSI® B550M PRO-VDH WIFI motherboard. This Quick Start section provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. Please link to the URL to watch it with the web browser on your phone or tablet. You may have even link to the URL by scanning the QR code.
Page 3
⚠ Important If you are installing the screw-type CPU heatsink, please follow the figure below to remove the retention module first and then install the heatsink. スクリュータイプのCPUクーラーを取り付ける場合は 、 下記の図のように 、 まずリテンション モジュールを外してからCPUクーラーを取り付けて下さい 。 나사타입의 CPU 히트싱크를 장착 할 경우, 아래 그림과 같이 쿨러 지지대를 제거 후 히트싱크를...
Page 5
Connecting the Front Panel Header/ フロントパネルヘッダーの接続/ 전면 패널 커넥터 연결하기/ 連接前置面板針腳/ 连接前置面板接头 Youtube 优酷 ⚽ ⚽ http://v.youku.com/v_show/id_XNjcyMTczMzM2.html http://youtu.be/DPELIdVNZUI Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch JFP1...
Page 7
Connecting the Power Connectors/ 電源コネクターの接続/ 전원 커넥터 연결하기/ 插上電源接頭/ 连接电源接头 Youtube 优酷 ⚽ ⚽ http://youtu.be/gkDYyR_83I4 http://v.youku.com/v_show/id_XNDkzODU0MDQw.html ATX_PWR1 CPU_PWR1 Quick Start...
Page 8
Installing SATA Drives/ SATAドライブの取り付け/ SATA 드라이브 설치하기/ 安裝 SATA 磁碟機/ 安装 SATA 设备 Youtube ⚽ http://youtu.be/RZsMpqxythc 优酷 ⚽ http://v.youku.com/v_show/ id_XNDkzODU5MTky.html VIII Quick Start...
Page 9
Installing a Graphics Card/ グラフィックスカードの取り付け/ 그래픽 카드 설치하기 / 安裝顯示卡/ 安装显卡 Youtube ⚽ http://youtu.be/mG0GZpr9w_A 优酷 ⚽ http://v.youku.com/v_show/ id_XNDkyOTc3MzQ4.html Quick Start...
Page 10
Connecting Peripheral Devices/ 周辺機器の接続/ 주변 장치 연결하기/ 連接周邊設備/ 连接外围设备 Quick Start...
Page 11
Power On/ 通電/ 전원 켜기/ 啟動電源/ 开机 Quick Start...
Safety Information ∙ The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly. ∙ Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start.
∙ Supports non-ECC UDIMM memory ∙ Supports ECC UDIMM memory ∙ Supports un-buffered memory * Please refer www.msi.com for more information on compatible memory. ∙ 1x PCIe 3.0/ 4.0 x16 slot (PCI_E1)* Expansion Slot ∙ 2x PCIe 3.0 x1 slots * The supported specification depends on installed processor.
Page 16
Continued from previous page AMD B550 Chipset ∙ 4x SATA 6Gb/s ports ∙ 2x M.2 slots (Key M) ▪ M2_1 slot (from processor) ▫ Supports PCIe 4.0/ 3.0 x4 * Storage ▫ Supports SATA 6Gb/s ▫ Supports 2242/ 2260/ 2280 storage devices ▪...
Page 17
Continued from previous page ∙ 1x 24-pin ATX main power connector ∙ 1x 8-pin ATX 12V power connector ∙ 4x SATA 6Gb/s connectors ∙ 2x M.2 slots (M-Key) ∙ 1x USB 3.2 Gen 1 5Gbps Type-C port ∙ 1x USB 3.2 Gen 1 5Gbps connector (supports additional 2 USB 3.2 Gen 1 5Gbps ports) ∙...
Page 18
BIOS Features ∙ ACPI 6.0, SMBIOS 2.8 ∙ Multi-language ∙ Drivers ∙ DRAGON CENTER Software ∙ CPU-Z MSI GAMING ∙ Google Chrome™, Google Toolbar, Google Drive ∙ Norton™ Internet Security Solution ∙ Mystic Light ∙ User Scenario ∙ Hardware Monitor ∙...
Page 19
Continued from previous page ∙ Audio ▪ Audio Boost ∙ Network ▪ Intel WiFi ∙ Cooling ▪ Pump Fan ▪ Smart Fan Control ∙ LED ▪ Mystic Light Extension (RAINBOW/RGB) ▪ EZ LED Control Special Features ▪ EZ DEBUG LED ∙...
M.2 screws (3 pcs./pack) Accessories Case badge Product registration card Application Driver DVD Quick installation guide Documentation MSI components compatibility & reward program card ⚠ Important If any of the above items are damaged or missing, please contact your retailer. Package contents...
Rear I/O Panel Wi-Fi Antenna PS/2 Combo connectors Line-In USB 3.2 Gen 1 1 Gbps LAN (5Gbps) Type-A Mic-In USB 2.0 Flash BIOS Button Type-A Line-Out DisplayPort Flash BIOS USB 3.2 Gen 1 Port (5Gbps) Type-A ∙ Flash BIOS Port/ Button - Please refer to page 32 for Updating BIOS with Flash BIOS Button.
Page 22
∙ Device Selection - allows you to select a audio output source to change the related options. The check sign indicates the devices as default. ∙ Application Enhancement - the array of options will provide you a complete guidance of anticipated sound effect for both output and input device. ∙...
Page 23
Installing antennas 1. Screw the antennas tight to the antenna connectors as shown below. 2. Orient the antennas. Rear I/O Panel...
This motherboard is designed to support overclocking. Before attempting to ∙ overclock, please make sure that all other system components can tolerate overclocking. Any attempt to operate beyond product specifications is not recommended. MSI does not guarantee the damages or risks caused by inadequate ® operation beyond product specifications.
It is recommended to use a more efficient memory cooling system for full DIMMs installation or overclocking. The stability and compatibility of installed memory module depend on installed CPU ∙ and devices when overclocking. Please refer www.msi.com for more information on compatible memory. ∙ Overview of Components...
PCI_E3: PCIe 3.0 x1 (PCH) ⚠ Important If you install a large and heavy graphics card, you need to use a tool such as MSI ∙ Gaming Series Graphics Card Bolster to support its weight to prevent deformation of the slot.
M2_1~2: M.2 Slots (Key M) ⚽ Video Demonstration Watch the video to learn how to Install M.2 module. http://youtu.be/JCTFABytrYA M2_1 M2_2 M2_1 slot installation 1. Loosen the screws of M.2 SHIELD FROZR heatsink. 2. Remove the M.2 SHIELD FROZR and remove the protective films from the thermal pads.
Page 29
3. Move and fasten the M.2 standoff to the appropriate position for your M.2 SSD, or remove the M.2 standoff if your M.2 SSD length is same as the length of M.2 heatsink to avoid damage to the M.2 SSD. 4.
JFP1, JFP2: Front Panel Connectors These connectors connect to the switches and LEDs on the front panel. Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch...
JUSB1: USB 3.2 Gen 1 5Gbps Type-C Connector This connector allows you to connect USB 3.2 Gen 1 5Gbps Type-C connector on the front panel. The connector possesses a foolproof design. When you connect the cable, be sure to connect it with the corresponding orientation. USB Type-C Cable JUSB1 USB Type-C port on...
JUSB3~4: USB 2.0 Connectors These connectors allow you to connect USB 2.0 ports on the front panel. USB0- USB1- USB0+ USB1+ Ground Ground No Pin ⚠ Important ∙ Note that the VCC and Ground pins must be connected correctly to avoid possible damage.
CPU_FAN1, PUMP_FAN1, SYS_FAN1~3: Fan Connectors Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with speed control signal. DC Mode fan connectors control fan speed by changing voltage. The auto mode fan connectors can automatically detect PWM and DC mode.
JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable. Normal Trigger the chassis (default) intrusion event Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis. 2.
JBAT1: Clear CMOS (Reset BIOS) Jumper There is CMOS memory onboard that is external powered from a battery located on the motherboard to save system configuration data. If you want to clear the system configuration, set the jumpers to clear the CMOS memory. Keep Data Clear CMOS/ (default)
(12V/G/R/B) with the maximum power rating of 3A (12V). Always turn off the power supply and unplug the power cord from the power outlet ∙ before installing or removing the RGB LED strip. ∙ Please use MSI’s software to control the extended LED strip. Overview of Components...
(5V). In the case of 20% brightness, the connector supports up to 200 LEDs. ∙ Always turn off the power supply and unplug the power cord from the power outlet before installing or removing the RGB LED strip. Please use MSI’s software to control the extended LED strip. ∙ Overview of Components...
EZ Debug LED These LEDs indicate the debug status of the motherboard. CPU - indicates CPU is not detected or fail. DRAM - indicates DRAM is not detected or fail. VGA - indicates GPU/ PCIE/ M.2 device is not detected or fail.
Installing OS, Drivers & Utilities Please download and update the latest utilities and drivers at www.msi.com Installing Windows® 10 1. Power on the computer. 2. Insert the Windows® 10 installation disc/USB into your computer. 3. Press the Restart button on the computer case.
UEFI has many new functions and advantages that traditional BIOS cannot achieve, and it will completely replace BIOS in the future. The MSI UEFI BIOS uses UEFI as the default boot mode to take full advantage of the new chipset’s capabilities.
BIOS Setup The default settings offer the optimal performance for system stability in normal conditions. You should always keep the default settings to avoid possible system damage or failure booting unless you are familiar with BIOS. ⚠ Important BIOS items are continuously update for better system performance. Therefore, the ∙...
Updating BIOS Updating BIOS with M-FLASH Before updating: Please download the latest BIOS file that matches your motherboard model from MSI website. And then save the BIOS file into the USB flash drive. Updating BIOS: 1. Insert the USB flash drive that contains the update file into the USB port.
Page 44
1. Please download the latest BIOS file that matches your motherboard model from the MSI® website. 2. Rename the BIOS file to MSI.ROM, and save it to the root of your USB flash drive. 3. Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU and memory.)
EZ Mode At EZ mode, it provides the basic system information and allows you to configure the basic setting. To configure the advanced BIOS settings, please enter the Advanced Mode by pressing the Setup Mode switch or F7 function key. Screenshot A-XMP Profile Setup Mode switch...
Page 46
∙ System information - shows the CPU/ DDR speed, CPU/ MB temperature, MB/ CPU type, memory size, CPU/ DDR voltage, BIOS version and build date. ∙ Boot device priority bar - you can move the device icons to change the boot priority. The boot priority from high to low is left to right.
Page 47
▪ To add a BIOS item to a favorite menu 1. Select a BIOS item not only on BIOS menu but also on search page. 2. Right-click or press F2 key. 3. Choose a favorite page and click on OK. ▪...
Advanced Mode Press Setup Mode switch or F7 function key can switch between EZ Mode and Advanced Mode in BIOS setup. BIOS menu BIOS menu selection selection Menu display ∙ BIOS menu selection - the following options are available: ▪ SETTINGS - allows you to specify the parameters for chipset and boot devices. ▪...
OC Menu This menu allows you to configure the frequencies and voltages for overclocking. Please note that, higher frequency and voltage may benefit overclocking capability but cause system un-stability. ⚠ Important Overclocking your PC manually is only recommended for advanced users. ∙...
Page 50
▶ Memory Try It ! [Disabled] It can improve memory compatibility or performance by choosing optimized memory preset. This item will be available when the installed processor supports this function. ▶ Memory Failure Retry [Enabled] Enables or disables the system reboot function when the memory OC retry fails. ▶...
JFP1 、 JFP2: フロントパネルコネクター これらのコネクターにはフロン トパネルのスイッチとLEDを接続します 。 Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch Reserved No Pin Buzzer Speaker - Buzzer +...
6. Press any key to boot from CD or DVD... というメッセージが表示されたら、 任意のキ ーを押します。 (スペースキーやEnterキーが無難です。 ) 7. 画面に表示される説明に従ってWindows® 10をインス トールします。 ドライバーのインストール 1. Windows® 10を起動させます。 2. MSI®ドライバーディ スクを光学ドライブに挿入します。 3. 「Select to choose what happens with this disc」ポップアップ通知をクリック し、それからRun DVDSetup.exeを選択してインストーラーを開きます。Windows コントロールパネルからの自動再生機能をオフにすると、ユーザーはまだMSIド ライバーディスクのルートパスからDVDSetup.exeを手動で実行します。 4. インス トーラーが自動的に起動し、 必要なドライバー/ ソフトウェアを全部リス トアップ...
Page 89
목차 안전 지침 ........................ 2 사양 ......................... 3 제품 내용물......................8 후면 I/O 패널 ......................9 LAN 포트 LED 상태 표시 ..................9 Realtek 오디오 콘솔 ....................9 구성품 개요......................12 프로세서 소켓 ......................13 DIMM 슬롯 ......................14 PCI_E1~3: PCIe 확장 슬롯 ..................15 SATA1~4: SATA 6Gb/s 커넥터...
안전 지침 ∙ 이 패키지에 포함된 부품은 정전기 방전(ESD)에 의해 파손될 우려가 있으므로 다음의 설명에 따라 컴퓨터를 조립하십시오. ∙ 모든 부품이 제대로 연결되었는지 확인하십시오. 제대로 연결되지 않을 경우, 컴퓨터가 부품을 인식하지 못하거나 컴퓨터를 켤 수가 없게 됩니다. ∙ 부품의 예리한 부분에 손을 다칠 수 있으므로 메인보드 취급시 가장자리 부분을 잡으십시오. ∙...
Page 91
∙ 듀얼 채널 메모리 구성 ∙ non-ECC UDIMM 메모리 지원 ∙ ECC UDIMM 메모리 ∙ un-buffered 메모리 지원 * 호환 가능한 메모리에 대한 최신 정보는 http://www.msi.com을 방문하여 알아보시기 바랍니다. ∙ PCIe 3.0/ 4.0 x16 슬롯 1개 (PCI_E1)* 확장 슬롯 ∙ PCIe 3.0 x1 슬롯 2개...
Page 92
이전 페이지로부터 계속 AMD B550 칩셋 ∙ SATA 6Gb/s 4포트 ∙ M.2 슬롯 2개 (Key M) ▪ M2_1 슬롯 (프로세서) ▫ PCIe 4.0/ 3.0 x4* 지원 스토리지 ▫ SATA 6Gb/s 지원 ▫ 2242/ 2260/ 2280 저장 장치 지원 ▪ M2_2 슬롯 (B550 칩셋) ▫...
Page 93
이전 페이지로부터 계속 ∙ 24핀 ATX 메인 전원 커넥터 1개 ∙ 8핀 ATX 12V 전원 커넥터 1개 ∙ SATA 6Gb/s 커넥터 4개 ∙ M.2 슬롯 2개 (M-Key) ∙ USB 3.2 Gen 1 5Gbps C타입 1포트 ∙ USB 3.2 Gen 1 5Gbps 커넥터 1개 (외 USB 3.2 Gen 1 5Gbps 2 포트...
Page 94
BIOS 기능 ∙ ACPI 6.0, SMBIOS 2.8 ∙ 다국어 ∙ 드라이버 ∙ 드래곤 센터 소프트웨어 ∙ CPU-Z MSI 게이밍 ∙ 구글 유틸리티 : 크롬, 툴바, 드라이브 ∙ 노턴™ 인터넷 시큐리티 솔루션 ∙ 미스틱 라이트 ∙ 사용자 시나리오 ∙ 하드웨어 모니터...
Page 95
이전 페이지로부터 계속 ∙ 오디오 ▪ 오디오 부스트 ∙ 네트워크 ▪ 인텔 WiFi ∙ 쿨링 ▪ 펌프 팬 ▪ 스마트 팬 컨트롤 ∙ LED ▪ 미스틱 라이트 익스텐션 (RAINBOW/RGB) ▪ EZ LED 컨트롤 특수 기능 ▪ EZ 디버그 LED ∙ 성능 ▪...
(2 케이블/팩) Wi-Fi 안테나 M.2 나사 (3 pcs./팩) 악세사리 케이스 배지 제품 등록 카드 애플리케이션 드라이브 DVD 빠른 설치 설명서 서류 MSI 컴포넌트 호환성 & 리워드 프로그램 카드 ⚠ 중요사항 위 항목 중 하나라도 손상되었거나 누락되었다면 대리점에 문의하십시오. 제품 내용물...
후면 I/O 패널 Wi-Fi 안테나 PS/2 콤보 커넥터 라인 입력 USB 3.2 Gen 1 1 Gbps LAN (5Gbps) A타입 마이크 입력 USB 2.0 플래쉬 BIOS 버튼 A타입 라인 출력 디스플레이포트 플래쉬 BIOS USB 3.2 Gen 1 포트 (5Gbps) A타입 ∙ 플래쉬 BIOS 포트/ 버튼 - 32 페이지의 내용을 참조하여 플래쉬 BIOS 버튼으로 BIOS를 업데이트하는...
Page 98
∙ 장치 선택 - 오디오 출력 소스를 선택하여 관련 옵션을 변경합니다. 체크 표시된 장치가 기본 장치입니다. ∙ 애플리케이션 강화 - 출력 및 입력 장치의 예상 음향 효과에 대한 가이드를 전부 제공합니다. ∙ 메인 볼륨 - 바를 조정하여 볼륨을 조정하거나 전면 또는 후면 패널에 연결된 스피커의 오른쪽/왼쪽...
Page 99
안테나 설치하기 1. 아래 그림과 같이 안테나를 안테나 커넥터에 단단히 나사로 고정합니다. 2. 안테나의 방향을 정합니다. 후면 I/O 패널...
프로세서 소켓 CPU 중심에서 가장 가까운 DIMM 슬롯까지의 거리 53.8 mm AM4 CPU 소개 메인보드에 CPU를 정확하게 배치하기 위하여 AM4 CPU표면에 노란색 삼각형이 있습니다. 노란색 삼각형은 1 번 핀을 나타냅니다. ⚠ 중요사항 프로세서를 변경할 때, AM4 프로세서 구성 특성으로 인해 시스템 구성을 지우고 BIOS를 ∙...
풀 DIMM 설치 또는 오버클로킹을 위해 보다 효율적으로 메모리 냉각 시스템을 사용할 것을 ∙ 권장합니다. ∙ 오버클로킹시의 안정성과 설치된 메모리 모듈의 호환성은 설치된 CPU 및 장치에 따라 달라집니다. 호환 가능한 메모리에 대한 자세한 정보는 www.msi.com을 방문하여 알아보시기 바랍니다. ∙ 구성품 개요...
중요사항 크고 무거운 그래픽 카드를 설치할 경우, 그래픽 카드를 안전하게 지지하여 슬롯의 변형을 ∙ 방지하기 위해 MSI 게이밍 시리즈 그래픽 카드 지지대와 같은 장치를 사용하시면 더욱 안전합니다. ∙ 확장 카드를 추가하거나 제거할 때 먼저 전원을 끄거나 전원 코드를 콘센트에서 뽑으세요.
JFP1, JFP2: 전면 패널 커넥터 이 커넥터를 사용하여 전면 패널에 있는 스위치 및 LED를 연결할 수 있습니다. 전원 LED 전원 스위치 JFP1 Reserved HDD LED 리셋 스위치 HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch...
CPU_PWR1, ATX_PWR1: 전원 커넥터 이 커넥터를 사용하여 ATX 전원 공급 장치를 연결할 수 있습니다. CPU_PWR1 Ground +12V Ground +12V Ground +12V Ground +12V +3.3V +3.3V +3.3V -12V Ground Ground PS-ON# Ground Ground Ground ATX_PWR1 Ground Ground PWR OK 5VSB +12V +12V +3.3V Ground...
JUSB1: USB 3.2 Gen 1 5Gbps C타입 커넥터 이 커넥터를 사용하여 전면 패널의 USB 3.2 Gen 1 5Gbps C타입 커넥터를 연결할 수 있습니다. 이 커넥터는 풀 프루프(foolproof )로 작동하도록 디자인되었으며 케이블 연결시 정확한 방향으로 연결하시기 바랍니다. USB C타입 케이블 JUSB1 전면...
⚠ 중요사항 ∙ VCC 및 그라운드 핀을 정확히 연결하여야 손상을 방지할 수 있습니다. ∙ USB 포트를 통하여 iPad,iPhone 및 iPod를 충전하려면 MSI 드래곤 센터 유틸리티를 ® 설치하시기 바랍니다. JTPM1: TPM 모듈 커넥터 이 커넥터는 TPM (Trusted Platform Module) 모듈에 연결됩니다. 자세한 내용과 사용방법은...
CPU_FAN1, PUMP_FAN1, SYS_FAN1~3: 팬 커넥터 팬 커넥터는 PWM (Pulse Width Modulation) 모드와 DC 모드로 분류될 수 있습니다. PWM 모드 팬 커넥터는 12V의 일정한 출력을 제공하고 속도 제어 신호에 따라 팬의 회전 속도를 조정합니다. DC 모드 팬 커넥터는 전압의 변화에 따라 팬의 회전 속도를 제어합니다. 자동 모드...
JBAT1: CMOS (Reset BIOS) 클리어 점퍼 메인보드에 시스템 구성 데이터를 유지하기 위해 외부 배터리로부터 전원을 공급 받는 CMOS 메모리가 있습니다. 시스템 구성을 지우려면 점퍼를 아래와 같이 설정하여 CMOS 메모리를 지우세요. 데이터 유지 CMOS 클리어/ (기본 설정) BIOS 리셋 기본 값으로 BIOS 리셋하기 1.
JRGB 커넥터는 최대 3A (12V) 정격 전력에서 최대 2미터 연속 5050 RGB LED 스트립 ∙ (12V/G/R/B)을 지원합니다. RGB LED 스트립을 설치 또는 제거하기 전에 항상 전원 공급 장치의 전원을 끄고 전원 ∙ 코드를 콘센트에서 뽑아주세요. ∙ MSI 소프트웨어를 사용하여 확장된 LED 스트립을 조정하세요. 구성품 개요...
RGB LED 스트립(5V/Data/Ground)을 지원합니다. 밝기 20%의 경우에 커넥터는 최대 200 개의 LED를 지원합니다. RGB LED 스트립을 설치 또는 제거하기 전에 항상 전원 공급 장치의 전원을 끄고 전원 ∙ 코드를 콘센트에서 뽑아주세요. ∙ MSI 소프트웨어를 사용하여 확장된 LED 스트립을 조정하세요. 구성품 개요...
EZ 디버그 LED 이 LED는 메인보드의 디버그 상태를 나타냅니다. CPU - CPU가 감지되지 않거나 고장났음을 나타냅니다. DRAM -DRAM이 감지되지 않거나 고장났음을 나타냅니다. VGA - GPU/ PCIE/ M.2 장치가 감지되지 않거나 고장났음을 나타냅니다. BOOT - 부팅 장치가 감지되지 않거나 고장났음을 나타냅니다. LED_SW1: EZ LED 컨트롤...
OS, 드라이브 & 유틸리티 설치하기 공식 웹사이트 www.msi.com 을 방문하여 최신 버전의 유틸리티와 드라이버를 다운로드 및 업데이트하세요 . Windows 10 설치하기 ® 1. 컴퓨터의 전원을 켭니다 . 2. Windows® 10 설치 디스크 /USB 를 컴퓨터에 삽입합니다 . 3. 컴퓨터 케이스의 Restart 버튼을 누릅니다 .
MSI UEFI BIOS는 UEFI(Unified Extensible Firmware Interface) 구성과 호환 가능합니다. UEFI는 기존 BIOS에서 이루지 못한 많은 새로운 기능과 이점을 가지고 있으며, 향후 BIOS 를 완전히 대체할 것입니다. MSI UEFI BIOS는 UEFI를 기본 부팅 모드로 사용하여 새 칩셋의 기능을 최대한 활용합니다. 그러나 CSM(Compatibility Support Module) 모드는 이전 장치와...
BIOS (바이오스) 설정 기본 설정은 일반적인 조건에서 시스템의 안정성을 위해 최적의 성능을 제공합니다. BIOS에 익숙하지 않을 경우, 시스템 손상 또는 부팅 실패를 방지하기 위해 항상 기본 설정을 유지하기 바랍니다. ⚠ 중요사항 BIOS 항목은 시스템 성능 향상을 위해 지속적으로 업데이트됩니다. 따라서 여기에 제공된 ∙...
재설정하려면 CMOS 클리어 점퍼 섹션을 참조하세요. BIOS(바이오스) 업데이트 M-FLASH로 BIOS 업데이트 업데이트 하기전: 구입한 모듈에 맞는 최신 BIOS 파일을 MSI 웹사이트에서 다운로드한 후 BIOS 파일을 USB 플래시 드라이브에 저장합니다. BIOS 업데이트: 1. 업데이트 파일이 들어있는 USB 플래시 드라이브를 컴퓨터에 삽입합니다.
Page 120
저장합니다. 3. CPU_PWR1 및 ATX_PWR1에 전원 공급 장치를 연결합니다. (CPU와 메모리 설치할 필요없음) 4. MSI.ROM 파일이 저장된 USB플래시 드라이브를 후면 I/O 패널의 플래쉬 BIOS 포트에 연결합니다. 5. 플래쉬 BIOS 버튼을 눌러 BIOS를 플래쉬하면 LED 표시등이 깜빡이기 시작합니다. 6. 100%로 완료되면 LED 표시등이 꺼집니다.
EZ 모드 EZ 모드는 시스템의 기본 정보를 제공하고 시스템의 기본 설정을 구성할 수 있습니다. 고급 BIOS 설정을 구성하려면 설정 모드 스위치 또는 F7 기능 키를 눌러 고급 모드로 이동하십시오. 스크린샷 A-XMP 프로필 설정 모드 스위치 검색 언어 시스템 정보 크리에이터 지니...
Page 122
∙ 시스템 정보 - CPU/ DDR 속도, CPU/ MB 온도, MB/ CPU 타입, 메모리 용량, CPU/ DDR 전압, BIOS 버전 및 시스템 구축 날짜 등 정보를 표시합니다. ∙ 부팅 장치 우선순위 바 - 장치 아이콘을 이동하여 부팅 순위를 변경합니다. 왼쪽에서부터 오른쪽으로...
Page 123
▪ 즐겨찾기 메뉴에 BIOS 항목을 추가하기 1. BIOS 메뉴 및 검색 페이지에서도 BIOS 항목을 선택합니다. 2. 마우스의 오른쪽 버튼 또는 F2 키를 클릭합니다. 3. 즐겨찾기 페이지를 선택한 후 OK를 클릭합니다. ▪ 즐겨찾기 페이지에서 BIOS 항목 삭제하기 1. 즐겨찾기 페이지에서 BIOS 항목을 선택합니다. 2.
고급 모드 설정 모드 스위치 또는 F7 기능 키를 누르면 EZ 모드와 고급 모드 사이에서 전환할 수 있습니다. BIOS 메뉴 선택 BIOS 메뉴 선택 메뉴 디스플레이 ∙ BIOS 선택 메뉴 - 다음과 같은 옵션이 제공됩니다. ▪ SETTINGS(설정) - 이 메뉴를 사용하여 칩셋 및 부팅 장치에 대한 설정을 지정할 수 있습니다.
OC 메뉴 이 메뉴를 사용하여 오버클로킹에 대한 주파수 및 전압을 구성할 수 있습니다. 높은 주파수와 전압은 오버클로킹 기능에 도움이 될수 있지만 시스템이 불안정해질 수 있습니다. ⚠ 중요사항 이 항목은 고급 사용자만을 위한 항목입니다. ∙ 오버클로킹은 보증하지 않습니다. 부적절하게 작동하였을 경우 보증이 무효화 되며 컴퓨터 ∙...
Page 126
▶ Memory Try It ! [Disabled] 이 기능은 최적의 메모리 프리셋을 선택하여 메모리 호환성 또는 성능을 향상시켜 줍니다. 이 항목은 프로세서가 이 기능을 지원하는 경우에만 변경됩니다. ▶ Memory Failure Retry [Enabled] 메모리 OC가 실패할 때 시스템 재시도 기능을 활성화하거나 비활성화 합니다. ▶...
JFP1, JFP2: 系統面板接頭 這些接頭用於連接前面板的開關和 LED 指示燈 。 Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch Reserved No Pin Buzzer Speaker - Buzzer +...
JUSB1: USB 3.2 Gen 1 5Gbps Type-C 接頭 這個接頭可供連接前面板上的 USB 3.2 Gen 1 5Gbps Type-C 接頭 , 這個接頭具有防呆設 計 。 請務必以相應的方向連接線纜 。 USB Type-C 線纜 JUSB1 前面板上的 USB Type-C 連接埠 JUSB2: USB 3.2 Gen 1 5Gbps 接頭 這些接頭用於連接前面板的 USB 3.2 Gen 1 5Gbps 連接埠 。 Power USB2.0+ USB3_RX_DN...
EZ 偵錯 LED 指示燈 這些 LED 指示燈會表示主機板的偵錯狀態 。 CPU - 表示未偵測到 CPU 或已故障 。 DRAM - 表示未偵測到記憶體或已故障 。 VGA - 表示未偵測到 GPU/ PCIE/ M.2 裝置或已故障 。 BOOT - 表示未偵測到開機裝置或已故障 。 LED_SW1: EZ LED 指示燈控制 此開關用於打開/ 關閉主機板上的所有 LED 指示燈 。 LED_OFF LED_ON (預設值) 元件總覽...
JFP1, JFP2: 前置面板接口 这些接口连接至前置面板上的开关和 LED 灯。 Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch Reserved No Pin Buzzer Speaker - Buzzer + JFP2...
JUSB1: USB 3.2 Gen 1 5Gbps Type-C 接口 此接口允许您在前置面板上来连接 USB 3.2 Gen 1 5Gbps Type-C 接口。 该接口具有防呆 设计。 当您连接电缆时, 请务必将其与相应的方向连接。 USB Type-C 电缆 JUSB1 前置面板上的 USB Type-C 端口 JUSB2: USB 3.2 Gen 1 5Gbps 接口 此接口允许您在前置面板上来连接 USB 3.2 Gen 1 5Gbps 端口。 Power USB2.0+ USB3_RX_DN...
简易侦错 LED 灯 LED 指示灯在主板中的侦错状态。 CPU - 表示 CPU 无法检测或故障。 DRAM - 表示 DRAM 无法检测或故障。 VGA - 表示 GPU/ PCIE/ M.2 设备无法检测或故障。 BOOT - 表示启动设备无法检测或故障。 LED_SW1: 简易 LED 灯控制 此开关用于打开/关闭主板上的所有 LED 灯。 LED_OFF LED_ON (默认) 组件概述...
Page 203
European Harmonized Standards. for recycling and disposing of their end-of-life products. The point of contact for regulatory matters is MSI, MSI-NL Eindhoven 5706 5692 ER Son. · Visit the MSI website and locate a nearby distributor for further recycling information.
Page 204
Unión Europea al final de su periodo de vida. Usted their useful life. MSI will comply with the product take debe depositar estos productos en el punto limpio...
Page 205
Products designed to be operated del suo ciclo di vita. MSI si adeguerà a tale Direttiva at closer proximities, such as tablet computers, comply with applicable EU requirements in typical ritirando tutti i prodotti marchiati MSI che sono stati venduti all’interno dell’Unione Europea alla fine del...