Means Embedded PC or Panel PC Means Embedded PC without Case Means Panel PC with Case Means Touch Type Means Resistive Touch Means Capacitive Touch Means LCD Brightness Means Common Brightness Means High Brightness PCB Version Baseboard PCB Version Number...
Page 6
2 x USB 2.0 Host,1 USB OTG 1 Channel 1000M LAN, Support POE(Optional). 2nd Channel 100M Optional 3.5mm Audio In/Out Connector,2W Speaker Audio Internal Buzzer RS232 2 Channels RS485 3 Channels * 2 Channels GPIO 8 Channels WiFi/BT On Board WIFI/BT...
Page 7
* This product has 5 channels of UART in total. The Bluetooth used one channel UART by default, the default setting is 2*RS232+2*RS485+Bluetooth.The UART can be changed between RS232 and RS485 easily. If you want different RS232 and RS485 setting, please contact us.
Page 8
Figure 1 Top View (Android) www.chipsee.com...
Page 9
Figure 2 Back View CS10768F097P- www.chipsee.com...
Page 10
C111 Figure 3 Top View (Android) www.chipsee.com...
Figure 4 Back View Power Input Connector The product CS10768F097E/CS10768F097P uses a wide range power input: 12~36V. The total power consumption is normally about 7W. The Power Input Connector is 3 Pin 3.81mm Screw www.chipsee.com...
Page 12
Terminal Connector, as Figure 5 shows. The Character “+” means power Positive input, The Character “–” means power Negative input. The Character “G” means system Ground. Table 1 has detailed descriptions about the connector definition. Figure 3 Power Input Connector...
Page 13
Capacitive Touch ATTENTION: Capacitive touch is very sensitive to power noise. Ripple voltage/current from the power adapter will cause the LCD ripples, and will also cause the capacitive touch malfunction: If you use the APK Multi-Touch under Android to test, you can find the touch point float.
Page 14
The CAN+RS485+RS232 connector is a 16 Pin 3.81mm Screw Terminal Connector, as Figure 6 shows. As for the definition of every pin, please refer to Table 2.This product has 5 channels of UART in total, they can be configured as RS232 or RS485 freely.
Page 15
Pin 1 CAN2_H CPU CAN Channel 2 H signal Pin 2 CAN2_L CPU CAN Channel 2 L signal Pin 3 CAN1_H CPU CAN Channel 1 H signal Pin 4 CAN1_L CPU CAN Channel 1 L signal Pin 5 RS485_2-...
USB HOST Connector The product CS10768F097E/CS10768F097P has two USB connectors as Figure 7 shows. These two USB can provide 500mA current each. Figure 7 USB HOST Connector USB OTG Connector product CS10768F097E/CS10768F097P connector as Figure 8 shows. It works as slave by default.
Figure 8 USB OTG Connector LAN Connector The product CS10768F097E/CS10768F097P has one channel 1000Mbit Ethernet Connector (LAN1), as Figure 9 shows. And this port supports POE (Power-On-Ethernet, optional, not supported by default). The other one channel 100Mbit Ethernet Connector is optional.
The product CS10768F097E/CS10768F097P has one TF (uSD) card connector as Figure 10 shows. This device supports TF (uSD) card up to 32GB. Figure 10 TF Card Connector ATTENTION: The TF card slot is NOT mounted with any TF card by default.
Page 19
Figure 11mini-PCIe Connector&4G Module Figure 12 SIM Card Holder Figure 13 4G Antenna ATTENTION: This product is not mounted on any 4G module by default. The Ubuntu driver for the 4G module is not available right now. www.chipsee.com...
Audio Connector The product CS10768F097E/CS10768F097P has one Audio Input (“Line-in”) and one Audio (“Line-out”) output, as Figure 14 shows. And the product has an internal 2W speaker. Figure 14 Audio Connector WiFi+BT The product CS10768F097E/CS10768F097P has one WiFi+BT. It uses Realtech RTL8723 which integrates WiFi and BT.
Figure 15 WiFi+BT Module Figure 16 WiFi+BT Antenna HDMI Connector The product CS10768F097E/CS10768F097P has one HDMI connector as Figure 17 shows. The HDMI output resolution can be configured by software. www.chipsee.com...
Figure 17 HDMI Connector Boot Switch The product CS10768F097E/CS10768F097P has a boot switch which can be used to change boot sequence, as Figure 18 shows. It is defined as SW2 on the PCB. As for the details of the boot switch, please refer to Table 3.
Download GPIO Connector The product CS10768F097P-R141 has one GPIO Connector, as Figure 19 shows. This connector is labelled as P28 on the PCB. As for the definition of every Pin, please refer to Table 4. Figure 19 GPIO Connector...
Page 24
Pin Number Definition Pin 1 VCC, Isolated Power 5VInput Pin 2 Pin 3 OUT1 Pin 4 OUT2 Pin 5 OUT3 Pin 6 OUT4 Pin 7 Pin 8 Pin 9 Pin 10 Measurements and Mounting Measurements of CS10768F097E The measurement of CS10768F097E-C111 is 226*172*26mm.
Page 25
This product CS10768F097E-C111 can be mounted using the 4 screw holes on the PCB. Please make sure the display is not exposed to high pressure when mounting into an enclosure. Measurements of CS10768F097P The measurement of CS10768F097P-C111 is 256*207*29mm.
When the product is out of power, please also take anti-static measures before touching the circuit board. How to Get Support Chipsee assumes no responsibility for any errors, which may appear in this manual. Furthermore, Chipsee reserves the right www.chipsee.com...
Page 29
Chipsee products are not authorized for use as critical components in life support devices or systems. www.chipsee.com...
Need help?
Do you have a question about the PPC-A9-97-C and is the answer not in the manual?
Questions and answers